Elite Screens Elite Home Series User manual

Electric Projection Screen
Elite Home Series
USER’S GUIDE
Matte White Screen
Rev. 1.1

INSTALLATION GUIDE
 Please read this guide prior to installation.
 Make sure the current rating is equal to the appliance rating when an extension cord is
used.
 Do not use any accessories not provided by the manufacturer. We will not be responsible
for any risks of fire, electric shock, or injuries resulting from the use of other accessories
not supplied by the manufacturer.
 Make sure the screen is mounted in a horizontal level. We suggest consulting with a
professional such as a carpenter, or using a laser leveler.
MOUNTING INSTALLATION
Wall Mounting Ceiling Mounting
I. Masonry Anchor is applied on concrete wall / ceiling; Plastic Plug is applied on wooden
wall / Ceiling.
II. Plastic Plug & wooden screw are applied to the wooden wall / ceiling for screen sizes
equal to or less than120”(diagonal). Masonry anchor is for concrete wall / ceiling
installations and for screen sizes greater than 120”(diagonal).
III.Install the Alum Extruded Hanger Set onto the slide channel and move to the desired
position before it is screwed on tightly.
Rev. 1.1
MOUNTING ACCESSORIES
1. ScrewNut(M10)x4 5. AlumExtrudedHangerx2
2. Boltx2 6. MasonryAnchorx2
3. ScrewNut(M6)x4 7 PlasticPlugx2
4. Washer x 4 8. Wooden Screw x 2

SETTING THE LIMIT POSITIONS
Every Home Series electric screen is designed to use a Limit Switch Adjusting Handle (in
yellow) to make the adjustment for lower/upper limit switch positions in lieu of traditional
adjustments by a screwdriver or allen wrench. The upper/lower limit
positions of the screen should already be properly adjusted by default. However you can set
more or less picture drop by following the instructions below.
1. Setting the “LOWER“ Limit Switch Position of Screen
Press the “DOWN” key on the transmitter/switch, and then pull the Adjusting Handle in
the DOWN Direction afterwards. Release the handle until the screen is down to the
desired position. The lower limit switch position has been reset.
2. Setting the “UPPER“ Limit Switch Position of Screen
Repeat the above “1“ procedure to set the upper limit position but use the “UP“ Key
instead.
(Yellow)
MORE PRECISE LIMIT SWITCH ADJUSTMENT
A. Setting precise lower limit switch position
1. Press the “DOWN“ key on the transmitter/switch and pull the Adjusting Handle in a
DOWN direction afterwards.
2. Release the Adjusting Handle when the screen reaches to 15 cm before the desired
position.
3. Press the “STOP“ key on the transmitter/switch and pull the Adjusting Handle in a
DOWN direction again.
4. Press the “DOWN“ key on the transmitter/switch again; the screen will rotate down in
a small step (about 3 cm), called “Step-Adjustment“.
5. Repeat procedures “3“ and “4“ continuously 2 more times so the screen can be
closely fitted to the desired position.
B. Repeat above steps 1-5 to set precise upper limit position.
Rev. 1.1

IR CONTROL DIAGRAMS
IR Remote Control kit Includes:
 1 Hand-held Transmitter
 1 Wall-mounted Receiver (built-in sensor)
 1 Sensor
There are two optional installations as illustrated in diagrams (A) & (B)
Transmitte
r
Connection pins
inside of case
Transmitter
Connection pins
inside of case
(A) (B)
1. Plug the wall-mounted receiver into the
pins of the case end as shown in diagram.
1. Insert the sensor into the pins of the
case end as shown in diagram.
2. Press the receiver’s up or down buttons
to control the screen. 2. Use the hand-held remote to control the screen and aim it directly at the sensor.
3. Or, use the hand-held remote but make
sure to aim it directly at the receiver. * Remote control can be used from a distance
up to 35 feet.
Infra-red codes
Up : B1 4E 90 6F
Stop : B1 4E 8A75
Down : B1 4E CA 35
Contact info:
15012 Red Hill Ave, Suite D
Tustin, CA 92780
Tel: [phone]
Fax: [phone]
www..elitescreens.com
[email protected]
Rev. 1.1