Elite Screens EDGE FREE Aeon Series User manual

Rev.070216-MZ
EDGE FREE
Applies to all available screen materials:
Product Description: The Aeon
Series is a fixed frame projection
The EDGE FREE® des
ign resembles a giant size flat
installation option to further enhance the frame appearance and
backlighting kit is available
for added visual appearance
Hardware and Parts List
Please make sure all parts listed below a
re included
A. Elbow joint x 4 pcs
B. Top/Bottom horizontal
fame x 4 pcs
E. Center Support bar x 1-2
pc
F. Wall brackets x
I. M6x12 screw x 2-12pcs J
. M5x50 screws and anchor x
M. Black Tape x 1 bag N. B
ezel trim
www.elitescreens.com
Aeon Series
EDGE FREE
®
Fixed Frame Projection Screen
User’s Guide
CineGrey 3D EDGE FREE® and
CineWhite
Series is a fixed frame projection
screen that
uses Elite’s EDGE FREE
ign resembles a giant size flat
panel TV display. The Aeo
n includes a
installation option to further enhance the frame appearance and
absorb projector overshoot
for added visual appearance
.
re included
before installation.
B. Top/Bottom horizontal
fame x 4 pcs
C. Left/Right vertical
frame x 2 pcs
F. Wall brackets x
2-3 pcs G. M6 screw x 2-12 pcs
H. M5x15 screw x
. M5x50 screws and anchor x
6 pcs
K. Rubber hammer x 1 pc
ezel trim
x 6 pcs O. Corner Support Bar
(180”-200”) x 4 pcs
1
Fixed Frame Projection Screen
CineWhite
™ EDGE FREE®
uses Elite’s EDGE FREE
™ technology.
n includes a
n ultra-thin trim as an
absorb projector overshoot
. An optional LED
D. Center joints x 2 pcs
H. M5x15 screw x
24 pcs
L. Screwdriver x 1 pc
O. Corner sleeve x 4 pcs

Rev.070216-MZ www.elitescreens.com 2
Frame Assembly
1. Insert the center joint into one of the ½ horizontal frames (B) and fasten it with the two M5x15 screws (H).
2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws.
3. Repeat steps 1 and 2 for assembling the second horizontal frame.
Push
4. Insert and slide in oneM6 screws (G) through the channel located on the back each horizontal frame.
5. Insert the elbow joint (A) into each end of the horizontal frames (B)as shown below.
Horizontal long frame (B)
ElbowJoint
(A)
ElbowJoint
(A)
Horizontal long frame
Place one M6 hex screw (G) in the center for attaching the center support bar (E)
Face up
M6 hex screws (G)
Horizontal frame
Center Joints
Top right Frame Top left Frame
Note: For models 180” and above, insert and slide in four M6 screws
(two on each frame) through the channel located on the back of each
horizontal frame section (top/bottom). Insert two M6 screws on each
vertical frame section (left/right).
Push

Rev.070216-MZ www.elitescreens.com 3
6. Insert the two vertical short frames(C) into the elbow joint (A).
7. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown below.
Horizontal long frame (B)
Vertical short frame (C)
Horizontal Long frame (B)
push
push
push
push
Note: For models 180” and above,
ensure two M6 screws (G) are
inserted on each vertical frame
before proceeding to step 7.
Face up

Rev.070216-MZ www.elitescreens.com 4
8. Make sure all four corners are properly in place to form a perfect square. Then fasten the four angles with the
M5x15 Screws (H).
Screen Material Installation
1. Lay the screen material completely flat with the front facing down on a clean surface in a horizontal position. The
back side of the screen material should be placed upwards.
Note: The back side of the material has the velcro borders all around the edges.
2. Carefully and gently place the assembled frame on top the screen material as shown below. Make sure to not allow
the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.
Four corners join correctly to form a perfect
square. Use the included screwdriver (L) to
fasten the Mx15 screws (H) into each corner
by aligning the frame screw holes to the
holes in the elbow joint (A).
Screen material back facing up
Screen material comer

Rev.070216-MZ www.elitescreens.com 5
3. After all of the corners of the frame have been properly aligned, attach the material to the frame in the following
order A→B→C→D (see instructions below for details).
Attach the screen material to the corners as shown below.
4. After all four corners have been attached; please check whether the frame corners are wrapped by the screen
material. If not, please loosen the velcro connection and repeat the above steps so the frame is not exposed.
Note: The black shaded part represents the velcro on the frame. That Velcro
end will ultimately attach with the other velcro end on the screen material.
Note:
Represents the
screen material
2) Fold over and attach
material to the velcro
strip of the frame.
3) Fold over second side
and attach to frame
4) Repeat until all four
sides are done in the
order A, B, C, D
1) Stretch the screen
material in the direction
of the arrowhead.
A
C A
B D

Rev.070216-MZ
5.
Proceed to attach the rest of the material to the frame as described in the illustrations below.
Grasp the middle
of the
material and attach it to the velcro
strip on the frame
Attach in the following sequence
C
www.elitescreens.com
Proceed to attach the rest of the material to the frame as described in the illustrations below.
Lay the Velcro end on the screen
material over the Velcro
frame and keep it within the edge.
Proceed
in the following sequence
below ①
②
The key is to attach within the
middle sections of 1 and 2. Then
continue attaching the remaining
unattached areas.
Repeat
the
remaining three sides in the
sequence A, B, C,
show below.
of the
screen
material and attach it to the velcro
Attach in the following sequence
: a-b-c-d
B
A
6
Proceed to attach the rest of the material to the frame as described in the illustrations below.
Lay the Velcro end on the screen
material over the Velcro
end of the
frame and keep it within the edge.
in the following sequence
②
The key is to attach within the
middle sections of 1 and 2. Then
continue attaching the remaining
unattached areas.
the
same steps on
remaining three sides in the
sequence A, B, C,
and then D as
D

Rev.070216-MZ www.elitescreens.com 7
6. If the material is too loose or tight after adjusting all four corner sides, then you will need to reattach the material.
Please follow the steps below to properly remove the screen material from the frame. This procedure will ensure
prolonging the life of the screen material.
Screen Material Removal
1. Detach the velcro from the frame.
2. Gently pull back the material to release it from the velcro connections on the corners
Support bar installation (for models under 180”):
1. Position the center support bar (E) in the middle of the frame and align the hole on each end of the support bar
with the M6 hex screws (G) on the top and bottom frames. Then fasten with the M6x12 screws (I).
Move the M6 hex screw (G) to the middle area of the frames.
Align the M6 screws
with the two holes.
Pull back the screen material from
the velcro connection along the
edges of the frame to detach it.
Center Support bar

Rev.070216-MZ
Support bar installation
(for models
1. Position the
center support bar (E)
hole on each end of the support bar with the
Then fasten with the
M6x12 screws (I).
2. Position the
Corner support bars (
below in fig 2. Align the holes on each end of the corner support bars with the M6 hex screws located
on the vertical and horizontal frame sections. Then fasten with the
Move the
M6 hex screw (
Corner Support Bar
Figure 1
Center Support bar
Align the M6
screws with the
two holes on the
Corner Support
Bars.
www.elitescreens.com
(for models
180” and above):
center support bar (E)
and M6 hex screws (G)
in the areas of the frame shown in fig 1. Align the
hole on each end of the support bar with the
M6 hex screws (G) loca
ted at the top and bottom frame
M6x12 screws (I).
Corner support bars (
O) and M6 Hex screws (G)
in the areas of the frame as shown
below in fig 2. Align the holes on each end of the corner support bars with the M6 hex screws located
on the vertical and horizontal frame sections. Then fasten with the
M6x12 screws (I
M6 hex screw (
G) to these areas of the frame.
Align the M6 Screws
with the two holes
located on the Center
Support Bar.
Corner Support Bar
8
in the areas of the frame shown in fig 1. Align the
ted at the top and bottom frame
sections.
in the areas of the frame as shown
below in fig 2. Align the holes on each end of the corner support bars with the M6 hex screws located
M6x12 screws (I
).

Rev.070216-MZ www.elitescreens.com 9
Notice to Installer:
Please use the following installation instructions to obtain superior optical performance from the CineGrey 3D Angular
Reflective ALR (Ambient Light Rejecting) Screen.
Make sure to follow these instructions in order for the CineGrey 3D to perform correctly.
•Angular-Reflective material is not compatible with ultra/short-throw projectors
•Minimum lens throw ratio 1.5x image width
•Ambient light must not come from the same direction as the projector
Since angular-reflective means that the projected image will reflect at the mirror-opposite angle, it is important to position
the projector so that the viewer will get the best possible image.
Step 1: Establish the general “eye level” of the viewers
Step 2: Set the appropriate projection level
Step 3: Adjust the screen height level and projection angle
Input Angle (A) = Output Angle (B) aligns with the viewer’s angle

Rev.070216-MZ www.elitescreens.com 10
Edge trim Installation
Included is an ultra-thin black edge trim that provides an elegant bezel finish
1. Place the assembled frame on a flat and clean surface. The projection screen surface should be facing up. Align the
tape with the edge of the screen, as shown in Figure 1. Once properly aligned, apply the black tape to the center of
the top and bottom of the screen material.
Figure 1
2. Without removing the adhesive tape, place all the trim pieces along the edge of screen material. Adjust the trim
pieces so that the four corners are evenly aligned. (Note: The Elite logo should be positioned on the bottom right).
Refer to Figure 2 below for a visual reference.
Figure 2
NOTE: Make sure the bottom edge trim with the Elite Screens logo is installed on the correct side. The back of the
material should be labeled with a DOWN sticker to indicate the material is facing in the down position. The Elite
Screens logo should be installed on the DOWN side
3. After properly aligning all trim pieces, carefully remove trim piece A (see Figure 3 below). Remove the inside
backing of the tape and place the trim piece in its original position on the frame. Repeat this step for the remaining
trim pieces in the following order: B-C-D-E-F.
Figure 3 The front side of the frame with trim pieces attached
Edge trim x 6 PCS
Black tape x1pcs
Trim
strip
Screen Material
The black tape
Front Side
Back Side
Plastic corner sleeve x4pcs
x4pcs
A
B
F
C
D
E
The black tape