Elite Screens GolfSim Portable Series User manual

Rev.V05262023DT (DS0232) 1 www.elitescreens.com
GolfSim Portable Series
Sports Simulation Impact/Projector Screen
User’s Guide –E/H Type
V1
__________________________________________________________________________________________________________________________________
Thank you for choosing the GolfSim Portable projection screen! Please read through this user guide
before utilizing the screen. Correct usage and maintenance will ensure a long product life.
Care & Use Instructions
◆Elite Screens highly recommends two people to assemble the GolfSim Portable screen.
◆Make sure to distinguish the front and back of the impact/projection screen when setting it up. The backside
has the Velcro. Follow the instructions in the screen assembly section to assure the front side of is set up
properly.
◆Be sure to use the screen only during a light breeze (up to wind speeds of 7 mph); it is not meant to withstand
heavy winds. *Elite Screens is not responsible for damages due to negligence resulting from misuse under
weather conditions and will void your warranty.
◆Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points
below to prevent that from occurring:
1. Do not touch the projection surface with your hands.
2. Do not write or draw on the projection surface.
3. Do not point at the projection surface with your fingers or sharp objects; this will damage the screen
material.
4. Use a soft bristle brush or dry microfiber cloth to remove dust from the screen surface.
5. Do NOT use any solutions, chemical cleaning agents, alcohol, or abrasive to clean the screen surface.
6. When cleaning the projection surface, use a soft cloth dampened with warm water to remove any traces.
7. Do NOT rub or apply pressure when cleaning the surface.
8. Use a fabric steamer no higher than Polyester setting to remove any wrinkles or folds in the material.
◆After using the screen, disassemble it and store it in the carrying bag provided.
◆To avoid damage and injury, the screen should only be operated by adults.
Product Description
Design: The aluminum frame is designed to be light weight and easily operated making it easy to carry,
assemble and disassemble.
Screen Fabric: The screen fabric is attached to the rectangular frame and held in place by Velcro
strips, which ensure an evenly stretched and flat surface. The ImpactWhite™screen material is
durable and can be folded many times without causing damage or distortion to the surface.
Installation Tips and Precautions
We consider our impact screens a wearable item and the life of them will vary according to their use.
1. Make sure to allow proper distance for swing range to protect children, pets, ceilings, walls, windows, or any other
property.
2. Avoid using golf balls with scuffs or markings to maximize the life of your ImpactWhite™360 screen. If possible,
use new golf balls.
3. Never place the screen over a window or under constant sun exposure. Solar radiation from direct sunlight destroys
the synthetic fibers of the screen.

Rev.V05262023DT (DS0232) 2 www.elitescreens.com
Hardware and Parts list
Note: Before assembling the screen, make sure all the above components are included.
A: Top Folding frame x 1
B: Bottom Folding frame x 1
C: Left Folding frame x 1
D: Right Folding frame x 1
E: M8 Knob screws x 8
F: Impact golf screen material x 1
G: Top Enclosure Cover x 1
H: Left Enclosure Cover x 1
I: Right Enclosure Cover x 1
J: Ball Bungees x 6
K: Velcro Strips x 12
L: Protection sheet x 1
※ 2pcs with shorter cord
M. Gloves x 2

Rev.V05262023DT (DS0232) 3 www.elitescreens.com
Assembly diagram
F: Impact Golf Screen Material
G. Top Enclosure Cover
I.
Right Enclosure Cover
H: Left Enclosure Cover
K: Velcro Strips
J: Ball Bungees
E: M8 Knob Screws
E: M8 Knob Screws
D: Right Folding Frame
A: Top Folding Frame
C: Left Folding Frame
B: Bottom Folding Frame

Rev.V05262023DT (DS0232) 4 www.elitescreens.com
Frame assembly
1. Take the frames out of the carrying bag, unfold and place them on the protection sheet (L) as shown below.
2. Fasten the frame pieces together at all four locations as shown above using the knob screws (D)
LOCK CENTER JOINTS AND CORNER HINGES
•Center Joints: Unfold the frame until the latch on the hinge “clicks” into place.
TIP: Gently lift the frame to ensure the hinge is locked (button pops up).
•Corner Hinges: Unfold the frame’s corner hinges until they “click” into place.
Push the hinge bar in until it
is straight and not bending.
Popped up button
indicates the hinge
is locked.
Pushed in button
indicates the hinge
is not locked.
CAUTION: BE AWARE OF PINCH POINTS.
Align the frame’s screw
holes to fasten them with
the knob screws (C)
Align the frame’s
screw holes to fasten
them with the knob
screws (D)
Note: The button's direction
here can distinguish the
position of the left/right
frame
(Please note that the button
must be on the inside when
installing)
Right frame (D)
Bottom frame (B)
Left frame (C)
Top frame (A)

Rev.V05262023DT (DS0232) 5 www.elitescreens.com
Impact Screen, Left/Right/Top Enclosure Cover Assembly
1. Please follow below instructions to place the screen material before assembly, and make sure the screen
material back side facing up.
Note: The impact screen has Velcro (soft fuzzy side) on Top edge. This is the back side of the impact screen.
2. Attach the Impact golf screen material (F) on the frame with Velcro with Gloves (M).
Align and fasten the material on the
lower edge of the frame with the velcro.
Press and smoothen to keep material flat.
Insert the loop end of the
bungee
(J) through
the grommet on the impact screen (F), wrap
it under the frame, and hook it over the ball.
Repeat on other side.
Note: Use bungee with a
shorter length for top side
Place the impact screen with the velcro side up.
The left side of the material is roughly aligned
with the edge of the frame corner.
(
Note: Attach velcro on the side which with
green sticker marked.)
Green color
Right side of screen material
(With Velcro of hook side)
Unfold the impact screen with the
back side facing up.
Bottom side of screen
material (Without Velcro)
Left side of screen material
(With Velcro of hook side)

Rev.V05262023DT (DS0232) 6 www.elitescreens.com
1. Left (H) and Right (I) side enclosure cover assembly.
1. Prepare the enclosure
covers for attachment to
the frame by identifying
the front and back.
Note: The black side faces
in, and the silver side
faces out.
2. Aligned velcro the
enclosure cover to the
inside of the small side
frame from bottom to top.
3. Velcro the enclosure
cover and impact
material together after
aligning their edges.
Left enclosure cover (H)
Right enclosure cover (I)

Rev.V05262023DT (DS0232) 7 www.elitescreens.com
3.Top enclosure cover (G) assembly.
(A) Attach Left and Right sides
Align and velcro the enclosure cover to
the outer side of the small side frame
from bottom to top.
Stretch the enclosure cover to
reach the right side.
Pull the enclosure cover tightly
and velcro it to the outer side of
the frame.
(B) Attach Top side
Attach Impact Screen and Top/Right/Left enclosure panels
1. Lift the frame gently with the help of two people.
CAUTION: Make sure all leg hinges are locked before lifting the assembled frame to standing position.
Left side
Right side
Position the top enclosure
cover so the black side faces in,
and the silver side faces out.
Velcro the enclosure cover to the
back of the frame.
Note: Attach velcro on the
side which with red
sticker marked.
Attachment complete.
Red color
Push the hinge bar in until it is
straight and not bending.

Rev.V05262023DT (DS0232) 8 www.elitescreens.com
2. Attach the Left/Right enclosure cover (H / I) to secure on the bottom of the frame legs.
3. Install Ball Bungees (J) and attach the Impact screen (F) to the enclosure covers.
Left leg
view
Left side view
Finish attaching the net part of the
enclosure cover by snapping it to the press
stubs on the legs. Repeat on other side.
Velcro together the
impact screen and
enclosure cover from
top to bottom. Repeat
on left side.
Insert the loop end of the bungee
(J) through
the grommet on the Impact screen
(F), wrap it
under the frame leg, and hook it over the ball.
Repeat on other side.
Right side view
Snap the bottom of the enclosure
cover to the press stud on the
inner side of the frame.
Left enclosure cover (H)
Repeat the same procedure for
the Right enclosure cover (I).

Rev.V05262023DT (DS0232) 9 www.elitescreens.com
Impact screen surface tension and flatness adjustment
Wrap tie six Velcro strips (K) on each vertical side frame evenly as instructed below to pull the impact
screen material to tension it.
Finished!
Wrap one end of the velcro strip on the
vertical frame with the soft fuzzy side
facing in.
Open the edge of the
materials and attach
the other side of the
velcro strip.
Seal the edge tightly
between the enclosure
cover and screen
material to secure the
velcro stip.
Turn in the direction of the arrow to
tighten the velcro strip. Inspect the
impact screen for surface flatness
and adjust as needed.

Rev.V05262023DT (DS0232) 10 www.elitescreens.com
Disassembly and repack into bag
Please follow the installation instruction to disassemble the components.
And refer below instruction to place the components into bag.
For local Elite Screens contact or Technical Support, please visit
www.elitescreens.com