Elite Screens Evanesce Plus Series User manual

Rev.040313-JA www.elitescreens.com 1
Large In-Ceiling Electric Motorized Front Projection Screen
Evanesce Plus Series
User’s Guide
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra
Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.
Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to
this unit are prohibited and will void your warranty. For more information, please contact our Technical
Support Department at [phone] Ext. 604.
Please retain this user’s guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by
the manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
The power outlet supplying power to the unit should be close to the unit and easily accessible.
Do not install the unit on uneven, inclined surfaces;
Do not install in damp places to avoid an electric shock or short circuit.
Do not place any heavy objects over the power cord.
Position the power cord properly to avoid creating a trip obstacle.
To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the
power cord.
The internal & external parts of this unit are not end user serviceable. Do not attempt to
disassemble this unit by yourself. No one except authorized technicians can open and make
repairs to this unit.
Make sure the power source that this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure the cord has an equal rating as the
appliance to avoid over heat.
Do not handle the power plug when your hands are wet or your feet are in contact with water.
Properly dispose of this equipment according to the environmental regulations in your area
when product is no longer of service.

Rev.040313-JA www.elitescreens.com 2
Do not use this unit under the following circumstances.
Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.
Avoid direct sun light, rain shower and moisture.
Keep away from fire sources and high temperature to prevent this device from overheating.
Cut off the power supply first before transportation or maintenance.
To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is
obvious damage or if there are any evident broken parts.
Installation Warning
The instructions provided in this user’s guide are for reference only. Please consult a professional
installation company for further installation and safety advice. The installer must insure that proper
mounting hardware is used to provide adequate strength suitable for the installation. Elite Screens is
not liable for any faulty installations. For limit adjustment instructions, please contact our Technical
Support Department at [phone] Ext. 604
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black
drop in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
Reorient or relocate the receiving antenna of the device which may be casing the interference.
Increase the separation between the screen and the device’s receiver.
Connect the equipment into a different power outlet other than the device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with
foreign particles such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
the fasteners that are used are of adequate strength and suitable for the installation location.

Rev.040313-JA www.elitescreens.com 3
UP
Stop
Down
Accessories for Evanesce Plus Series
Please make sure all accessories listed below are included before proceeding.
Control System for Evanesce Plus Series
5-12 VOLT TRIGGER CABLE
1. 5-12V Trigger: The built-in 5-12V trigger input
allows your screen to synchronize its drop & rise
with the projector’s power cycle. The screen
deploys when the projector powers up and will
retract when the projector powers down. The 5-
12 volt adaptor connects to your projector’s
trigger output via a separate cable that may or
may not be provided by the manufacturer of the
projector. The trigger feature will not work
without an output cable from the projector, but it
can be tested by connecting the Red (+) and
Green (-) cable to a 9-volt battery.
2. 3-Way Wall Switch: The 3-way wall
switch is a wall mount control box with
an up/stop/down button and plugs
directly into the screen’s RJ-45 input.
3. IR “Eye” Receiver: plugs directly into the
screen’s RJ-45 input to present a low profile
line-of-sight control option for your IR remote
control even in a recessed ceiling installation.
4. IR Remote Control: The Infrared
functions by direct line of sight contact
with a beam range of 30 feet.
5. RF Remote Control: The radio waves
eliminate the need for a direct line of
sight with a range of 100 feet.
A. IR Remote
B. RF Remote
D. 3-way
wall switch
E. IR eye
receiver
G. AAA
Batteries x 2
C. Remote
control base
x 2
G. Bubble
leveler
Red + Green -
F. 5-12v trigger cable
RJ45 input

Rev.040313-JA www.elitescreens.com 4
Hardware Parts List for Evanesce Plus Series
Please make sure all parts listed below are included before proceeding with the installation.
A. Hexagonal nut x 4
B. M6x13 hex screw x 8
C. Hanging bracket x 2
D. Washer x 12
E. Turnbuckle x 4
F. Suspension Bar x 4
G. M6 nut x 4
H. End cover flange panel
Power
The Evanesce Plus Series includes a 3-Prong Power Cord for use in a non-concealed power outlet. If your
installation will be entirely concealed (including the power outlet), Elite Screens strongly recommends a
hardwire connection. Please refer to the image below for both 110v & 220v wiring information.
Assembly
1. Insert the M6x13 hex screw (B) through the Hanging Bracket’s (C) screw hole and secure with
the Hexagonal nut (A). Slide the Hanging Bracket (C) through the railing on top of the case.
Repeat the same for the other side.

Rev.040313-JA www.elitescreens.com 5
2. Attach the Turnbuckle (E) to the bottom of the Suspension Bar (F) and secure with the Hex
Screw (B), Washer (D) and Hex Nut (H).
3. Attach the Turnbuckle (G) to the Hanging Bracket (C) as shown in figure below. Install the Suspension
Bars (D) to your ceiling according to their distance.
4. Attach the end flange piece (C) on the long edge of the housing as shown below to complete the
assembly. The screen is now ready for installation.
B
D
D
H
E
C
Rotate the turnbuckle
as needed to adjust
the height level.

Rev.040313-JA www.elitescreens.com 6
Side schematic diagram:
For local Elite Screens contact or Technical Support, please visit
www.elitescreens.com
Leaning the end flange piece and
put the bottom part so it may
insert into the housing groove.
Push the end flange upwards to allow the
top part and housing to come together.
Ceiling
End flange piece location
Attention:
1. The end flange panels can easily warp. Please be
careful when handling them and during installation.
2. Make sure the end flanges are properly installed
and leveled with the housing.
3. As a safety precaution four people are required
for this installation.