Elite Screens Lunette Series User manual

Rev. 042610-JA
www.elitescreens.com [e-mail]
Lunette Series
Home Theater Fixed Frame Curved Projection Screen
User’s Guide

1
Important Safety and Warning Precautions
Please follow these instructions carefully to ensure proper maintenance and safety with your
Lunette Series Fixed Frame Curved Screen
1. When hanging the screen up, please make sure that no other objects such as power switches, outlets,
furniture, ladders, windows, etc. occupy the space designated for your Fixed-Frame screen.
2. Regardless if the screen is hung on or installed into the wall, make sure that the proper mounting anchors
are used and that the weight is supported appropriately by a strong and structurally sound surface just as
any large and heavy picture frame should. (Please consult a home improvement specialist for the best advice
on installation)
3. Frame parts are made of high quality velour-surfaced aluminum and should be handled with care.
4. When not in use, cover over the screen with a furniture sheet to protect it from dirt, grime, paint or any
other impurities.
5. When cleaning, use a damp soft cloth with warm water to remove any marks on the frame or screen
surface.
6. Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.
7. In order to avoid damaging the screen, avoid touching it directly with your fingers, tools or any other
sharp or abrasive objects.
8. Spare Parts should be placed out of reach for small children in accordance with household safety
guidelines.
CAUTION:
The projection screen frame is made of high-quality aluminum alloy and should be handled with
care.
Use a soft cloth with warm water to remove any spots on the screen surface.
To avoid damaging the screen material, never attempt to use any solutions, chemicals or
abrasive cleaners on the screen itself and never attempt to touch screen with your fingers or
sharps/abrasive objects.

2
Parts List
A. Dry-wall anchor B. 1.77”L-Bracket C. 3.54”L-Bracket D. Y-Bracket E. M5 Screw F. Wood screw
G. Fix Plate H. Center Support Bar I. Support Joiner J. Elbow Joint
K. Butterfly Screw L. Tension Rods
M. Vertical Upright Frame
N. Horizontal Curved Frame
O. Screen Material

3
Assembly
1. Insert both Elbow Joints (J) into each Horizontal Curved Frame (N) and join all four frame parts
together as shown below.
2. After making sure that all four corners join at right angles to form a perfect rectangle, fasten the
four angles together by using x8 M5 screws (E).
3. Lay out the Screen Material (O) and Tension Rods (L) on a clean and dry surface. Then, gently
roll out the screen material on the back of the fixed frame.
4. Insert the screen Tension Rods (L) through the sleeves according to their corresponding lengths on
each edge of the screen as seen below.
Vertical Upright Fame
Horizontal Curved Frame
Black Backing of the screen material
Minimal gap is normal here

4
5. Slip the screen tension rods into the grooves running along each side on the back of the frame. Clip
on the Fix Plates (F) to the back of the frame to secure the rods into place forming a tight and flat surface.
See Attaching the Fix Plates section below for details.
Tension Rod
Viewing Surface
Fix Plate

5
Black backing for AcousticPro1080 models
This procedure only applies to AcousticPro1080 models, disregard if your Curved frame is not an
AcousticPro1080 variant. The black backing counters the effects of light penetration that would otherwise
light up all items behind the screen and spoil the picture.
The black backing goes behind the projection surface and are held into position by Velcro-faced fix plates.
Fix plate secures AcousticPro1080 material
and the black backing behind it.
AcousticPro1080 Screen
Material Cover by Black back
Fix Plate
Tension Rod (stretches the
AcousticPro1080 material)
Black backing for
AcoousticPro1080
material
*An alternate way to attach the black backing is to utilize the Velcro tabs attached to the tops of the fix
plate’s tail (Fig. 4). The material will grab and hold tight to the Velcro as it lays over the tails of the fix
plates themselves and stretched from tab to tab around all four sides.
After the material has been installed, the backing will lay over the back of the white (AcousticPro1080)
material and then be held into place by the fix plates as they are added (Fig.1-3). Interval markings reveal
the best likely points of attachment (Fig. 1). The prongs on the fix plates (Fig. 2) straddle a lip on the back
of the frame creating a friction hold that will firmly keep the material and backing in place (Fig. 3-4).
Fig. 1
Fig. 3
Fig. 2
Fig. 4
Black backing

6
Attaching the Fix Plates
1. Make sure that the material and frame are both lying face down on a clean, dry and non-abrasive
surface.
2. Center the material inside the frame.
Please note the material will be noticeably smaller because stretching the material is required to
create a sufficient amount of tension for perfect material flatness.
3. Start attaching the Fix Plates in the center of the Horizontal Curved Frame’s edge and (1) then
alternate with the center short sides (2) as shown in diagram.
Note: Follow these instructions to make sure the material is properly fixed in the center position of the
frame. After attaching the Fix Plates in sequence #2 (the center of the short sides), please remove the
fix plates in sequence #1 (the center of the long horizontal edge) and reattach them again, and
also remove the fix plates on sequence# (2) and reattach them again.
4. Then continue to follow our recommended order numbers 3-8 to properly distribute tension to the
screen material.

7
Center Support Bar
1. Insert the Support Joiner (I) into each side of the Center Support Bar (H) to complete assembly.
Support joiner
Center support bar
2. Insert the Center Support Bar (H) into the upper top groove on the back of the frame (not the one where
the fix plate inserts) with the bottom end near the approximate center point of the frame and place it in at
an angle so that both ends of the bar are in alignment with the groove.
3. Slide the top end of the bar into the top center point location as shown below to complete the center
support bar installation. This will provide added stability to your frame and added tension to the
material.
支
撑
For 125”and above models

8
Installation
*Unit: inch (mm)
Curve235-85w
Curve235-96w
Curve235-103w
Curve235-115w
Curve235-125w
Curve235-138w
Curve235-147w
Curve235-158w
Parts List
(piece)
Horizontal Curved Frame
2
2
2
2
2
2
2
2
Upright Vertical Frame
2
2
2
2
2
2
2
2
Elbow Joint
4
4
4
4
4
4
4
4
M5*15 Assembly Screw
9
9
9
9
9
9
9
9
Screen Material
1
1
1
1
1
1
1
1
Top/Bottom Tension Rod
2
2
2
2
2
2
2
2
Side Tension Rod
2
2
2
2
2
2
2
2
Center Support Bar
1
1
1
1
2
2
2
2
Support Joiner
2
2
2
2
4
4
4
4
Fix Plate
44
52
54
56
62
66
68
72
Dry-wall anchor
7
7
7
7
9
9
9
9
M5*45 Wood Screw
7
7
7
7
9
9
9
9
1.77" L-Bracket
4
4
4
4
2
2
2
2
3.54" L-Bracket
0
0
0
0
2
2
2
2
Y-Bracket
1
1
1
1
1
1
1
1
Butterfly Screw
5
5
5
5
5
5
5
5
Installation
Guide
View Width (A1)
71.19(1986)
88.35(2244)
94.77 (2407)
105.83 (2688)
115.00 (2921)
126.97 (3225)
135.24 (3435)
145.40 (3693)
View Height (A2)
33.28 (845)
37.56 (954)
40.31 (1024)
45.00 (1143)
48.90 (1242)
53.98 (1371)
57.52 (1461)
61.81 (1570)
Overall Width (B1)
85.28 (2166)
95.43 (2424)
101.85 (2587)
112.90 (2868)
122.09 (3101)
134.06 (3405)
142.32 (3615)
152.48 (3873)
Overall Height (B2)
40.35 (1025)
44.65 (1134)
47.40 (1204)
52.09 (1323)
55.98 (1422)
61.06 (1511)
64.6 (1641)
68.90 (1750)
Frame Height ( C )
3.39 (86)
3.86 (98)
4.17 (106)
4.80 (122)
5.35 (136)
6.22 (158)
6.81 (173)
7.56 (192)
Distance (D)
39.96 (1050)
45.28 (1150)
47.24 (1200)
51.18 (1300)
59.06 (1500)
62.99 (1600)
66.93 (1700)
68.90 (1750)
Distance (E)
39.96 (1050)
45.28 (1150)
47.24 (1200)
51.18 (1300)
59.06 (1500)
62.99 (1600)
66.93 (1700)
68.90 (1750)
Model Number
Part Name

9
Midpoint (Y-Bracket)
L-point (L-Bracket)
R-point (L-Bracket)
Wall
Horizontal
Curved
Frame