Elite Screens PowerMax Series User manual

Rev.123011-AS
www.elitescreens.com [email protected] 1
Electric Motorized Projection Screen
PowerMax Series
User’s Guide

Rev.123011-AS
www.elitescreens.com [email protected] 2
Make sure to read this user’s guide and follow the procedure below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black
Top Drop in the roller. Please be aware o this as it will void your warranty with Elite Screens. Unapproved
changes or modi ications (except or cutting the power cord or hardwire installations) to this unit are
prohibited and will void your warranty. For more in ormation, please contact our Technical Support
Department at [phone] Ext. 604.
•Please retain this user’s guide for future reference.
•To avoid damaging the unit, do not use with any unauthorized accessories not
recommended by the manufacturer.
•Handle the unit carefully during transportation to avoid any damages.
•To ensure safe and reliable operation, direct connection to a properly grounded power
source is advised.
•The power outlet supplying power to the unit should be close to the unit and easily
accessible.
•Do not install the unit on uneven or inclined surfaces.
•Do not put heavy objects on the power cord and position it properly to avoid creating a
trip obstacle.
•ever overload the power cord to prevent an electric shock or fire due to a loose contact
or a short circuit.
•There are not user serviceable parts in this unit. Do not attempt to disassemble this unit
by yourself. o one except authorized technicians can open and make repairs to this unit.
•Make sure the power source this unit is connected to has a continuous power flow.
•If there is need to use an extension cord, make sure the cord has an equal rating as the
appliance to avoid overheat.
•Do not handle the power plug when your hands are wet or your feet are in contact with
water.
Do not use this unit under the following circumstances.
•Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
•Avoid direct Sunshine, rain shower and moisture.
•Keep away from fire sources and high temperature to prevent this device from
overheating.
•Cut off the power supply first before transportation or maintenance.
•Fully disconnect from the power supply when the unit is not in use for a long period of
time, as should be done with any other electric household appliance.
•To avoid possible injury and/or an electric shock, do not attempt to use the screen if there
is obvious damage or if there are any evident broken parts.
Important Safety & Warning Precautions

Rev.123011-AS
www.elitescreens.com [email protected] 3
Due to various installation environments, the instructions provided in this user’s guide are for
reference only. Please consult a professional installation company for further installation and
safety advice. The installer must insure that proper mounting hardware is used to provide
adequate strength suitable for the installation. lite Screens is not liable for any faulty
installations.
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black drop
in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the
manufacturer. Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
owever, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures.
Reorient or relocate the receiving antenna of the device which may be casing the interference.
Increase the separation between the screen and the device’s receiver.
onnect the equipment into a different power outlet other than the device.
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
that the fasteners used are of adequate strength and suitable for the installation location.
Installation Warning
Pre
-
Installation
NOTE

Rev.123011-AS
www.elitescreens.com
Hardware Parts List for the Powe
Please make sure all parts listed below are included before proceeding with the installation
a.
d.
Hardware Parts List
a.
Mounting Bracket
b. M4x50 Screw
c. M10 Anchor
d.
Suspended eiling Bracket onnector
e. M5x15 Screw
& Bolt
f. Bubble Level
[email protected]
Hardware Parts List for the Powe
rMax Series
Please make sure all parts listed below are included before proceeding with the installation
b.
c.
e. f
.
QTY
2
4
4
Suspended eiling Bracket onnector
2
4
1
4
rMax Series
00
Please make sure all parts listed below are included before proceeding with the installation
.
c.
.

Rev.123011-AS
www.elitescreens.com [email protected] 5
Please consult a professional Installer. Elite Screens is not liable for faulty installations.
Flush Mount to the Wall
1. Mark the location of where the screen is to be installed, drill your holes, and insert the
M10 Anchors (c).
2. Install the Mounting Brackets (a) to the wall and secure with the M4x50 Screws (b).
Mou Mounting Bracke Mounting Bracket
ix Plate 1
Anchor M4x50 Screw
Mounting Bracket
ix Plate 2
Wall Mounting
Bracket
Installation Instructions

Rev.123011-AS
www.elitescreens.com [email protected] 6
3. Attach the screen to the Mounting Bracket by inserting the top of the case to the first fix plate,
and securing the back of the case to the second Fix Plate. Make sure the case slots are securely
attached to the Mounting Bracket.
Mounting Bracket Mounting Bracket
ix Plate 1 ix Plate 2
Mounting Bracket Case Slot 1
Case Slot 2
Screen Case

Rev.123011-AS
www.elitescreens.com [email protected] 7
Flush Mount to the Ceiling
1. Mark the location of where the screen is to be installed, drill your holes, and insert the M10
Anchors (c).
2. Install the Mounting Brackets (a) to the ceiling and secure with the M4x50 Screws (b).
Ceiling M10 Anchor
3. Attach the screen to the Mounting Bracket by inserting the top of the case to the first Fix Plate,
and securing the back of the case to the second Fix Plate. Make sure the case slots are securely
attached to the anging Bracket.
M4x50 Screw
Mounting Bracket
ix Plate 1
Mounting Bracket
ix Plate 2
ix Plate
1
ix Plate
2

Rev.123011-AS
www.elitescreens.com
Suspended Ceiling using Chains
1.
You can also hang the screen on a ceiling by using chains (not included
2.
onnect the Suspended eiling Bracket onnector (d) to the
the M5x15 Screws & Bolts
(e).
M5x15 Bolt
(e)
Mounting Bracket
(a)
3. Insert chains (n
ot included) through the loop holes of the Suspended eiling Bracket onnector (d).
Sus
pended Ceiling Bracket Connector
Loop Holes
[email protected]
Suspended Ceiling using Chains
(additional hardware required)
You can also hang the screen on a ceiling by using chains (not included
).
onnect the Suspended eiling Bracket onnector (d) to the
Mounting Bracket
(a) and secure with
(e).
M5x15 Bolt
Suspended eiling Bracket
(d)
M5x15 Screw
(e)
ot included) through the loop holes of the Suspended eiling Bracket onnector (d).
pended Ceiling Bracket Connector
8
(a) and secure with
Suspended eiling Bracket
onnector
ot included) through the loop holes of the Suspended eiling Bracket onnector (d).

Rev.123011-AS
www.elitescreens.com
Built in 3 Way Control Switch
1. The PowerMax Series c
omes with a 3 Way ontrol Switch attached to the Power ord, which is 3.5
meters in length.
2. Use the provided
Bubble Level (f) to ensure the screen is level before plugging in the power cord.
3 Way Control
Up/Stop/Down
Switch
Remove Screen
from Mounting Brackets
1. Pull down on the Mounting
Bracket Release Tab and remove the bottom of the case first, away
from the wall/ceiling
, followed by the top of the case.
Release Tab
[email protected]
Built in 3 Way Control Switch
omes with a 3 Way ontrol Switch attached to the Power ord, which is 3.5
Bubble Level (f) to ensure the screen is level before plugging in the power cord.
Bubble Level f)
from Mounting Brackets
Bracket Release Tab and remove the bottom of the case first, away
, followed by the top of the case.
Pull Bottom of case first away from wall/ceiling.
9
omes with a 3 Way ontrol Switch attached to the Power ord, which is 3.5
Bubble Level (f) to ensure the screen is level before plugging in the power cord.
Bracket Release Tab and remove the bottom of the case first, away
Pull Bottom of case first away from wall/ceiling.

Rev.123011-AS
www.elitescreens.com
ZPM-
RT Optional Remote
Please contact Elite Screens to purchase the
A.
IR Remote
RF Remote 3 Way Wall Switch
Red+ Green -
E.
12V Trigger
IR Eye Receiver
[email protected]
RT Optional Remote
Control Kit for PowerMax Series
Please contact Elite Screens to purchase the
optional ZPM-RT
Remote ontrol Kit.
4 55”
B. .
RF Remote 3 Way Wall Switch
AAA Battery x 2
110”
F. G.
IR Eye Receiver
Wall Box
10
Control Kit for PowerMax Series
1
Remote ontrol Kit.
D.
AAA Battery x 2