Elite Screens YardMaster 2 WraithVeil Dual Series User manual

V04062020JA-Z 1 www.elitescreens.com
YardMaster 2 WraithVeil® DualSeries
180” Indoor/Outdoor Portable ProjectionScreen
User’s Guide –Z type
Thank you for choosing the Yard Master WraithVeil®Dual portable projection screen! Please read through this user
guide before utilizing the screen. Correct usage and maintenance will ensure a long product life.
Care & Use Instructions
◆Elite Screens highly recommends two people to assemble the Yard Master 2 WraithVeil®Dualscreen.
◆The WraithVeil®Dual is a 2-directional flexible vinyl projection screen material. It is designed to
accommodate either front or rear projection.
◆Be sure to use the screen only during a light breeze (up to 7 mph); it is not meant to withstand heavy winds.
*Elite Screens is not responsible for damages due to negligence resulting from misuse under weather
conditions and will void your warranty.
◆Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points
below to prevent that from occurring:
1. Do not touch the projection surface with your hands
2. Do not write or draw on the projection surface
3. Do not use fingers or sharp objects to point on the projection surface; this will damage the screen
material.
4. Use a soft-damp cloth to clean the projection surface; do not use chemical cleaning agents or alcohol.
5. Use clean water when dampening the cleaning cloth and do not rub against the material to cleanit.
◆After using the screen, disassemble it and store it in the carrying bagprovided.
◆To avoid damage and injury, the screen should only be operated by adults.
Product Description
Design: The aluminum frame is designed to be light weight and easily operated making it easy to carry, assemble
and disassemble.
Screen Fabric: The screen fabric is attached to the rectangular frame and held in place by several press stubs, which
ensure an evenly stretched and flat surface. The WraithVeil® Dual (front/rear projection) screen material is durable
and can be folded many times without causing damage or distortion to the surface.
Correct usage of the projection screen will ensure better viewing results.
For front projection, assemble and view the screen as indicated in Fig. 1.
For rear projection, assemble and view the screen as indicated in Fig. 2.
Fig. 1
Fig. 2

V04062020JA-Z 2 www.elitescreens.com
Hardware and Parts List
A. Folding frame x1
B. Left/Right folding legs x2
(Adjustable)
C. Center brace x1 (Adjustable)
D. Knob Screw
(Refer to Chart)
E. Center brace foot
(Refer to Chart)
F. Projection screen material x1
G. Screen material bag x1
H. Carrying Bag x1
I. Rope
J. Eyebolt x 2
K. Ground stake x 4
Note: The parts list above is subject to change without notice.
Models
Knob Screw
Center Brace Stand
Max Height
180” (16:9)
12 pcs
1 pc
163.3 inches
Frame Assembly
1. Take the folding frame (A) out of the carrying bag (H) and place it on a flat surface. Fully unfold the
longer sections first, as shown below.
2. Next, unfold the frame until the latch on the hinge “clicks” into place. Repeat the procedure for the
shorter sections, as shown below.
Note: When unfolding the frame and legs, be sure the latches on the hinges "click" into place. Please also
make sure all 4 corners of the frame are at a 90° angle and the hinged support bar is straight and not bent.
Fig 1
Fig 2
Fig 3
Fig 4
Fig 5
Fig 4

V04062020JA-Z 3 www.elitescreens.com
3. Next, screw the eyebolts (J) into the openings located at the top of the frame.
Screen Material Attachment
1. Take the screen material (F) out of the screen material bag (G) and align the corners of the screen material
with the inside corners of the frame.
2. Once the screen material is fully extended, secure the material by snapping the buttons onto the frame studs.
Fasten the buttons in the following order as shown onFig. 9.
Note: Snap the buttons on each corner first, then work your way out to the center on each side.
Leg Attachment and Height Adjustable feature
1. Carefully take the left and right folding legs (B) out of the carrying bag (H)
and place them on a flat surface. Unfold the leg(s) and make sure the hinges
click into place. Use the knobscrews (D) to attach the frame to the legs at the
desired location for your height requirement per the instructions below.
Fig 6
5
7
2
4
3
1
6
8
Fig. 9
Fig 7
Fig 8

V04062020JA-Z 4 www.elitescreens.com
Fig.13
Fig.14
2. Lay the frame on its backside on clean surface, then lay the legs over on the frame in the position desired.
3. Once you have aligned the leg’s holes with the frame’s holes, secure with the knob screws.
4. Tie 4 pieces of rope (2 on the left and 2 on the right) to the eyebolts (J) that are located at the top of the frame.
5. Next, lift the screen up while simultaneously opening the legs. Two people are needed for this step. Fig. 13-14.
6. Next, carefully unfold the back brace behind the leg and attach it using a knob screw(D). Fig. 16-17.
Warning: When attaching the legs, make sure to screw the top of the leg to the last hole of the
frame to reach max height. Attaching the legs lower to the frame and leaving an extra space on top
may cause the screen to tip over when assembled.
Location points for legs
Fig 10
Fig 16
Fig 11
Fig 12
Fig 15
Fig 17

V04062020JA-Z 5 www.elitescreens.com
Center Brace, Stake and Ropes
1. Unfold the center brace (C), fold the small end as illustrated (Fig. 18), align it to the bottom of the frame’s screw
hole and then secure it using a knob screw (D). Next, attach another center brace (depending on the height) using a
knob screw as shown in Fig 19. Then attach the center brace foot (E) to the bottom of the center brace (C).
2. To secure the frame, place a stake (K) into each hole located on the frame footing, and hammer it into the ground.
Finally, tie the 4 ropes (I) to the stakes and through the eyebolts (J) to prevent the screen from tilting or falling over.
As shown in Fig. 21
Screen Disassembly
1. After using the screen, disassemble and store it in the carrying bag (H). To disassemble the screen, follow
the assembly procedure in reverse order.
2. Store the screen in the provided carrying bag (H). Be sure to place folding frame, legs, and smaller parts
into the carrying bag first and place the material on top to keep material from creasing or tearing.
For more information, technical support or your local Elite Screens
contact, please visit www.elitescreens.com
Fig 18
Fig 21
Fig 20
Center Brace Foot
Fig 19