Elite Screens StarBright7 User manual

Rev.091709‐JA
www.elitescreens.com [e-mail]
StarBright7
Fixed Frame Projection Screen
User Guide
ecex


1
Attention:
The StarBright7 screen material is composed of high
quality sensitive multi-layer projection material.
Please follow the pre-cautions below for proper care
procedures and to prolong the life of your StarBright7.
Failure to comply will result in voiding your warranty.
Avoid using any chemical compounds or harsh
abrasives
which will result in permanently damaging
the
screen material.
 USE ONLY a soft non-abrasive cloth with mild soap
and water
to clean the screen material
 DO NOT rub the cloth with force when cleaning to
avoid permanently scratching the surface
 DO NOT touch the screen surface with sharp
objects
 USE ONLY a soft feathered brush to remove dust


2
Parts List

1.FramePartsx6pcs(4topframepcs.+2sideframepcs)
2.TensionRodsx6pcs(4top/bottomrods+2siderods)
3.StarBright7ScreenMaterialx1pc
4.Centerjointsx2pcs
5.ElbowJointsx4pcs
6.Wallbracketsx2‐3pcs(dependingonmodel)
7.Screwsx16pcs
8.UserGuidex1pc
9.CenterSupportBarx1‐2pcs(dependingonmodel)
10.Supportjoinerx2‐4pcs(dependingonmodel)
11.FixPlatesx30‐90pcs(dependingonmodel)
12.Cottonglovesx2

Note:Pleasemakesureallpartsareincludedinyourpackagebeforeproceedingtoassembleyour
EliteScreensfixedframeprojectionscreen.

ASSEMBLING THE FRAME


1.Insertjointconnectortohorizontalframepieceandthenfastenitwith2screws 














2.Inserttheotherhorizontalframepiecetothejointconnectorandthenfastenitwith2screws.












1/2Long frame
Push


3
Please do not tighten the screws completely, to make sure the frame piece lines up
correctly.

3.Insertbothcornerjointconnectorsintothelonghorizontalframe(seefig.1)










4. 
































Joinallfourframepartstogetherfollowingthestepsshowedbelow.(fig.2)
Join


4.Joinallfourframepartstogetherfollowingthestepsshowedbelow.(fig.2)
Push Push
Short frame
Short frame

Push Push
Joint
Long frame
( fig.1)


4
Push Push
( fig.2)
Insert the exposed ends of the joint connectors
into the short (vertical) frame and align the four
corners so that they meet at perfect right angles

































5.Aftermakingsurethatallfourcornersjoinatrightanglestoformaperfectrectangle, fastenthe
fouranglestogetherbyusingthe(x8)jointscrewsincluded.(seefig.3)







4.edgeofthescreenasseenbelow.(seefig.4)






Screw
( fig.3)


5
**Important:Readbeforehandlingmaterial**

TheStarbright7materialisprecisioncraftedtoperformitsroleasahighgain,highcontrastfront
projectionsurface.Becauseofthis,itisverysensitivetohowitishandled.
Whenassemblingthescreen,pleaserolloutthematerialslowlyandcarefully.Itiseasytocreasethis
materialbygrabbing,pinching,foldingorotherwisehandlingitinappropriately.Insteadoflayingitout
onacleanandlevelsurface,itisbettertounrollittoavoiddamage.Pleasekeepthematerialaway
frompetsandchildrensothattheydonotaccidentallytreadonit.



Thephotosaboveindicatehowasimpletwistinthematerialduringtheinstallationcancause
permanentdamage.Beextremelycarefulwithyoursetup,readtheinstructionscarefullyandconsult
anEliteScreensservicerepforanyquestionsregardingtheproductassembly.


Pre‐InstallationmaterialdamagedisclaimerforStarBright7


6
Attaching the StarBright7 screen material to the frame









(1)

Step1.Topreventdamagetothescreenmaterial,pleaseputonthecottongloves(included)andcarefullylayout
thescreenandframeonacleananddrysurface.
Step2.Removetheprotectivefilmonthescreenmaterial.
Step3.Keep“ThebackoftheScreenMaterial”tagandfaceupasshowninfig.(2).
Step3.Placethescreenmaterialonthebackoftheassembledframeasshowninfig.(3).
Step4.Carefullyunfoldthescreenmaterialandmakeitparallelwiththeframeasshowninfig.(4).









(2)(3)(4)

Step5.Removethewhitepaperverycarefullyasshowninfig.(5).









  (5)(6)

Step6.Insertthetensionrodsthroughthesleevesaccordingtothelengthoneachsideofthescreenandinsert
thetensionrodsintothegroovesofeachsideonthebackoftheframeasshowninfig.(6).
Step7.Attachthefixplatestotheframeinthepositionindicatedbytheredarrowsonthebackoftheframeas
showninfig.(7).











(7)(8)
Screenmaterial
Frame
Whitepaper
Screenmaterial
Tensionrod
Fixplate


7
CAUTION
Please follow these instructions carefully to ensure proper maintenance and safety
with your StarBright7 ez-Frame Screen
1. When hanging the screen up, please make sure that no other objects such as power switches,
outlets, furniture, ladders, windows, etc. occupy the space designated for your Fixed-Frame
screen.
2. Regardless if the screen is hung on or installed into the wall, make sure that the proper
mounting anchors are used and that the weight is supported appropriately by a strong and
structurally sound surface just as any large and heavy picture frame should.
(Please consult a home improvement specialist for the best advice on installation)
3. Frame parts are made of high quality velour-surfaced aluminum and should be handled with
care.
4. When not in use, cover over the screen with a furniture sheet to protect it from
dust, dirt, grime, paint or any other impurities.
5. Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.
6. In order to avoid damaging the screen, avoid touching it directly with your fingers, tools or
any other sharp or abrasive objects.
7. Spare Parts should be placed out of reach of small children in accordance with
household safety guidelines.


8

CenterSupportBard

1. Insertthesupportjoinerintoeachsideofthecentersupportbartocompleteassembly.


supportjoiner
Centersupportbar



2. InserttheCenterSupportBarintothegrooveonthebackoftheframewiththebottom
endneartheapproximatecenterpointoftheframeandplaceitinatananglesothatbothends
ofthebarareinalignmentwiththegrooveasshowbelow.

3. Slidethetopendofthebarintothetopcenterpointlocationtocompletecentersupport
barinstallation.Thiswillprovideaddedstabilitytoyourframeandaddedtensiontothe
material.







INSTALLATION
1. Locateyourdesiredinstallationlocationwithastudfinder(recommended)andmarkthe
drill‐holeareaofwherethescreenistobeinstalled.

2. Drillaholewiththeproperbitsizeaccordingtothewoodscrewsincluded.

3. Lineupthesmallwallbracketswiththedrilledholesontheinstallationlocationand
screwtheminusingaPhilipsscrewdriver.

4. Positionthefixedframescreenontothetopwallbracketsasshowninfig.1andpush
downatthecenterofthebottomframerailtohookintothelowerwallbracket.
CenterSupport Bar



9
Method 1 (smaller than 121" diagonal)
Method 2 (larger than 121" diagonals)
smallwallbrackets3pcs
Smallwallbracket5pcs
(Fig. 1)