Grandview CB-UY92 User manual

GRANDVIEW REPRODUCING GENUINE COLORS
Grandview Crystal Screen Canada Ltd.
#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada V5J 5G4
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.ca
Guangzhou Grandview Crystal Screen Co., Ltd.
P.O. 511400 Federal Ind. Zone No. 363, Yushan West Road,
Shiqiao, Panyu District, Guangzhou, Guangdong, China
Tel: [phone] Fax: [phone]
Website: www.grandviewscreen.com
www.grandviewscreen.com.cn
GRANDVIEW REPRODUCING GENUINE COLORS
Instruction Manual for
Cyber Portable Series Pull-Up Screen
Model：CB-Uxx
Thank you for purchasing a Grandview projection screen.
Before use, please read instructions carefully. After installation, store instructions for future reference.

1
1 Front casing
8 Uphold bar ①
②
①
8 Uphold bar ②
8 uphold bar ③
The model is a portable pull-up screen,the design is compact and lightweight.It is suited for
various venues such as business presentation boardromm home theathes and other
ententainment sites.
、 、 、
Description
2 Tube
3 Semicircle tube
4 End cap 5 Support foot
6 Foot wheel
7 Clip
9 Top lock
10 Uphold locker
11 Height adjustment
wheel
12 Handle
13 plastic handle base
14 Tube lock base
(front & back)
15 Tube lock activist
16 Screen fabric
10 Up locker hold
2 Tube
1 Back casing
Hook & Lock Assembly Screen Casing Assembly
1. Casing (front & back)
2 .Tube
3 .Semicircle tube
5 .Support foot
6 .Foot wheel
7 .Clip
4 .End cap
Upload Bar Assembly
8. Uphold bar ① ② ③
9. Top lock
11. Height adjustment wheel
10. Uphold locker
12. Handle
13. Plastic handle base
14. Tube lock base
(front & back)
15. Tube lock activist
16. Screen fabric

2
5
1.Put the screen on the ground, in a proper position, facing the projector. Turn the support foot
(5) out untill they are perpendicular to the screen casing (1). (Figure 1)
2.Lift the uphold bar ③ ② ( 8 ) 90 degrees vertically until it clicks. Raise the uphold bar (8 ) while
simultaneously pushing the uphold locker(10) .(Figure 2-4)
3.Pull up the screen by grasping the handle(12) and lock the handle base on the fastener at the
top of uphold bar(8). (Figure 5-7)
1.Control the uphold bar simultaneously pushing the uphold locker while pull up or down the
screen.Otherwise the screen will be damaged by fast down out of control.
2.Be sure the handle base were locked into the fastener at the top of uphold bar stable, and
the handle were fastened on the holder at the top of uphold bar.
1. Screen Fabric is not smooth when screen is unfolded.
Installation
Open Screen
Figure 1
Figure 2 Figure 3 Figure 4
Figure 5
Figure 6
Figure 7
Warnings
Malfunction solutions
a. Hold and push slightly fixed tube in the middle of position of tube untill loose from the
semicirde tube. (Figure 14)
b. Adjust the foot wheel of support and height adjust wheel.(Figure 15-16) ment
Figure 14 Figure 15 Figure 16
2.
The fixed holding bar can not be raised when it is in use.
a.Check whether the uphold bar is vertical to the outer case or refer to Installation Step3.

34
4.Pull up and lock the uphold bar(8) to the desired height . The screen is fully released . The
screen height could be adjusted to 6 different levels by adjusting locking position of uphold
bar. (Figure 8)
8 ②
8 ①
8 ③
Button
5.To get the flat screen by adjusting foot wheel.when it were declined.
1.Push the uphold locker using one hand
simultaneously pull down the uphold bar ( 8① )
with another hand . Repeat the same action to
low down the uphold bar (8②). (Figure 9)
2.Remove the handle fromthe fastener at the
top of uphold bar .Grasp the handle, lower the
screen to allow it retract into the case. Be sure
the handle base connected with tube lock base.
(Figure 10)
3.F old do wn and lock uph old ba r (8 ) to its
cli p(7)
③
. Re turn t he support foo t to or igina l
po sitio n.(Figure 11)
4.Be sure the screen is completely stowed and
locked before carrying the product by handle ,
even if the screen could be locked automatically
while the uphold bar were locked in the clip.
(Figure 12)
Figure 8
Retract screen
please retract the screen for store.
8 ③
Figure 9
Figure 12
Press gently
13 Plastic handle
base
Figure 11
7 Uphold bar fixer
Figure 10
13 plastic hook base
2 Tube
1 Front casing
14 Tube lock base
(front & back)