Elkay OBFATLFR8 1D Series Installation manual

OBFATLFR8*1D
97740C (7/01)PAGE 1
FIG. 1
See Fig. 3
USES HFC-134A REFRIGERANT
Installation, Care & Use Manual
27 53 19
20,21,
22,23
24,25
26
56
50
49
46,47,
48,51
44
18
57
34
45
30
31
43
40
35
32
37,38,
39
41,42,
55
36
33
58 54
52
32
59
8
29
28
28
17
60
62
64
63
61

OBFATLFR8*1D
97740C (7/01) PAGE 2
FIG. 2
FINISHED FLOOR
*ADA REQUIREMENT
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEAR-
ANCE FROM CABINET LOUVERS TO WALL.
F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
LEGEND A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE
CONNECT STUB 1-1/2 IN. (38 mm) OUT FROM WALL SHUT OFF BY OTHERS
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/2 O.D. DRAIN C = 1-1/2 TRAP NOT FURNISHED**

OBFATLFR8*1D
97740C (7/01)PAGE 3
HANGER BRACKETS & TRAP INSTALLATION
1) Remove hanger bracket fastened to back of cooler by removing one (1) screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support.
IMPORTANT:
 7-3/4 in. (197mm) dimension from wall to centerline of trap must be maintained for proper fit.
 Anchor hanger securely to wall using all six (6) 1/4 in. dia. mounting holes.
3) Install straight valve for 3/8" O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the hanger bracket is engaged properly in the slots on the cooler
back as shown in Figure 2.
5) Loosen the two (2) screws holding the lower front panel at the bottom of cooler base and two (2) screws at the top.
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install them on the cooler waste line making sure that the end of the
waste line fits into the trap. Assemble the slip nut and gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, adjust screw on regulator (item 15),
accessible by removing push button (Item 2, Fig. 3). CW adjustment will raise stream and CCW adjustment will lower
stream. For best adjustment, stream should hit basin approximately 6-1/2 (165mm) from bubbler.
5912
14
15
16 1
4
10
11
6
7
3
2
10
FIG. 3
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
PROTECT FROM HARD FREEZING
9) If the ambient air temperature drops below 0° F, the cooler needs to be drained of all water by blowing out all water
lines, evaporator (item 53), and the drain trap.
18

OBFATLFR8*1D
97740C (7/01) PAGE 4
Panel-Bottom Dispenser
Button - Push
Screw - Set
Panel-Right Side
Panel-Left Side
Panel-Front Push
Sleeve - Push Button
Cover - Cold Control
Washer
Screw-#8 x 5/8" Lg. Torx/Slot
Screw - Torx
Hex Nut
Panel - Screen
Retaining Nut
Regulator
Holder-Regulator
Screw-#10 x 1/2" Lg. THSM
Cover-Dispenser Bottom
Power Cord
Fan Blade
Hex Nut - Fan Blade
Fan Motor 115V
Screw - (Fan Motor)
Shroud - Fan
Screw - #8-18 x 3/8 Lg.
Clip (Front and Rear Panels)
Strainer
Bubbler
Screw - Torx
Condenser
Drier
Panel - Front Lower
Panel - Right Rear (Left Unit)
Panel - Left Rear (Left Unit)
Panel - Right Rear (Right Unit)
Panel - Left Rear (Right Unit)
Stud - Compressor Mtg.
Grommet - Compressor Mtg.
Clip - Compressor Mtg.
Compressor Serv. Pak EM65
Relay
Cover - Relay
Heat Exchanger
Drain Tube (Left Unit)
Drain Tube (Right Unit)
Gasket - Drain
Ring Support - Drain
Clamp - Drain Gasket
Basin - Stainless Steel
Adaptor - Basin
Hex Nut #10-32
Cold Control
Evaporator Assembly
Screw - #10 x 1/2" Lg. HHSM
Overload
Tee - 1/4 x 1/4 x 1/4
Drain Tube Assembly
Drain Trim Strip
Tubing - Poly (Cut To Length)
Bubbler - Nipple
Power Cord
Heater Strip
Rocker Switch
Heater Thermostat Assy
Hanger Bracket (Not Shown)
22897C
45662C
70022C
22822C
22814C
27295C
45663C
27124C
56033C
70864C
75500C
40045C
27469C
15005C
61313C
50986C
75532C
55931C
35870C
30699C
70018C
31490C
70009C
22899C
38417001
75524C
55996C
45392C
75566C
62152C
66202C
22955C
26776C
22854C
22862C
26800C
101516143550
100806740570
19037000
35960C
35959C
35768C
66576C
45332C
45331C
50400C
50401C
70444C
21903C
27306C
70016C
31513C
66534C
111411443890
35958C
70682C
40022C
26847C
56092C
15009C
35900C
35906C
35907C
35909C
400660943730
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
*40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
NS
ITEM NO. PARTNO. DESCRIPTION
*REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL
ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water
coolers or orders for repair parts MUST include Model No. and
Serial No. of cooler, name and part number of replacement part
WARNING!
This unit is frost resistant down to 0° F with no wind. Prevail-
ing winds can reduce the ability of the heater element to
prevent light freezing. If the ambient air temperature will drop
below 0° F, the cooler needs to be drained of all water by
blowing out all water lines, evaporator (item 53), and the
drain trap. A heater strip is used to heat the unit and will
begin to cycle at 40° +/- 5° F. A check at this temperature
will ensure the heater is working and the unit is resistant to
light freezing.
ALSO, MAKE SURE THERE ARE NO PLASTIC OR
FLAMMABLE COMPONENTS DIRECTLY ABOVE THE
HEATER STRIP.
ELKAY MANUFACTURING COMPANY  2222 CAMDEN COURT  OAK BROOK, IL 60523  630.574.8484
PRINTED IN U.S.A. FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
29
29
13
FIG. 4
FIG. 5
(with Compressor)
FIG. 6
(without Compressor)