Elkay SWIRLFLO EDFPBWM114C Instructions for use

Page 1
EDFPB114C EDFPBWM114C EDFPBV114C EDFPBWMV114C
97921C (Rev. F - 02/18)
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain ttings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building’s plumbing circuits.
EDFPB114C EDFPBWM114C
SWIRLFLO®Fountains with FLEXI-GUARD®
INSTALLATION & USE MANUAL
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 297921C (Rev. F - 02/18)
EDFPB114C, EDFPBWM114C, EDFPBV114C, EDFPBWMV114C
LEGEND
A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.
B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind
Wall. 1-1/4” O.D. Drain (Trap Not Furnished)
C = Opening For Optional AP-99 Access Panel
Figure 2 - Rough-in Assembly For EDFPB114C
Figure 1 - Rough-in for EDFPB114C W/MP86 Mounting Plate
Optional
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 3
EDFPB114C EDFPBWM114C EDFPBV114C EDFPBWMV114C
97921C (Rev. F - 02/18)
28 3/4"
730mm
29 1/4"
743mm
1 1/4"
32mm
FINISHED FLOOR
BACK PANEL
A
B
14 1/4"
362mm
C
OPTIONAL
43 5/8"
1108mm
9 3/4"
248mm
8"
203mm
8"
203mm
SURFACE MOUNTING
PLATE
26 1/2"
673mm
16"
406mm
8"
203mm
5 1/4"
133mm 5 1/4" 133mm
3/8" (10mm) DIA. HOLES
FOR MOUNTING PLATE
TO WALL (10)
1/4" (8mm) DIA. HOLES FOR
MOUNTING PLATE TO WALL
7 7/8"
200mm
LEGEND
A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.
B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind
Wall. 1-1/4” O.D. Drain (Trap Not Furnished)
C = Opening For Optional AP-99 Access Panel
NOTE: Reinforce The Wall In The Shaded Areas
Figure 4 - Rough-in Assembly for EDFPBWM114C
Figure 3 - Rough-in for EDFPBWM114C
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 497921C (Rev. F - 02/18)
EDFPB114C, EDFPBWM114C, EDFPBV114C, EDFPBWMV114C
27"
686mm
ADA
REQUIREMENT
33 15/16"
862mm
1 5/8"
41mm
5/8"
16mm
18 3/8"
467mm
21 15/16"
557mm
19 3/4"
502mm
FINISHED FLOOR
FINISHED WALL
MPW101 MTG. PLT.
REF. SEPARATE
INSTALLATION
INSTRUCTIONS
FOR DETAILS
Figure 5 -Rough-in EDFPB(V)114C W/MPW101 MOUNTING PLATE
Figure 6 -Rough-in Assembly EDFPB(V)114C W/MPW101 MOUNTING PLATE
LEGEND
A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.
B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind
Wall. 1-1/4” O.D. Drain (Trap Not Furnished)
C = 3/8” (10mm) DIA. Slots For Mounting Hanger Bracket To Wall
28 3/4"
730mm
29 1/4"
743mm
1 7/8"
48mm
16"
406mm
8"
203mm
1 1/4"
32mm
FINISHED FLOOR
BACK PANEL
HANGER BRACKET
MPW101
MTG. PLT.
43 1/2"
1105mm A
B
C
27 3/16"
691mm
26 9/16"
675mm
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 5
EDFPB114C EDFPBWM114C EDFPBV114C EDFPBWMV114C
97921C (Rev. F - 02/18)
Installation Instructions:
EDFPB114C W/MP86 MTG. PLT.
1. Wall should already be framed for the fountain using
the positioning dimensions shown in Figure 1. Shown
dimensions pertain to installation location (framing
must support up to 300 lbs. weight). These
dimensions are required for compliance with ANSI
Standard A117.0.
2. Install rough-in plumbing as shown in Figure 1. Run
supply water inlet line through the back panel. Install a
service stop (not provided). Turn on supply water and
ush thoroughly.
3. Install fountain. Remove screw (Item 10) from cover
plate and slide cover plate (Item 14) toward basin.
Mount the fountain to the wall and mounting plate with
(4) 5/16” hex nuts (provided with mounting plate).
Tighten securely. (See Figure 7)
4. Determine required length of waste line and cut to
appropriate length. 1-1/4” O.D. waste tube furnished.
1-1/4” slip trap, waste elbow and extension not
provided.
5. Make water supply connections from service stop to
the 3/8” O.D. unplated copper tube coming out of the
strainer. Turn on water supply and check for leaks
(See Figure 17). Newly installed water supply line
should be insulated after leak check is completed.
CAUTION: DO NOT SOLDER tubes inserted
into the strainer as damage to the
o-rings may result.
6. These products are designed to operate on
20-105 PSI supply line pressure. If the inlet
pressure is above 105 PSI, a pressure regulator
must be installed in the supply line. Any damage
caused by reason of connecting these products to
supply line pressures lower than 20 PSI or higher
than 105 PSI is not covered by warranty.
7. Check stream height from bubbler. Stream height is
factory set at 35 PSI. If supply pressure varies
greatly from this, remove push button (Item 3 -
Figure 14) and adjust the screw on the regulator
(Item 18 - Figure 14). To remove push button,
remove setscrew from bottom of sleeve (Item 15).
Insert a small punch in screw hole and push
up while grasping the push button and pull forward
removing the push button. Clockwise adjustment
will raise stream height and counterclockwise
movement will lower stream height. For best
adjustment stream should hit basin approximately
6-1/2” from the bubbler. Reassemble push button
by pushing in on button until the push button
catches in the sleeve. Reinstall the setscrew
(Item 6) in the sleeve (Item 15).
Figure 7 - EDFPB114C Fountain Installation
Figure 8 - AP-99 Panel (Optional)
10
5/16” Studs - Supplied with MP86
20
14
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 697921C (Rev. F - 02/18)
EDFPB114C, EDFPBWM114C, EDFPBV114C, EDFPBWMV114C
Figure 9 - Panel Installation
Figure 10 - Fountain Installation
Figure 11 - AP-99 Panel (Optional)
7
10
16
20
14
Installation Instructions:
EDFPBWM114C/EDFPB114 W/MPW101 MTG. PLT.
1. Fountains using the MPW Mounting Plate refer to Figure
5 for hanger bracket location and rough-in dimensions.
NOTE: Review separate installation instructions for details of the
MPW Mounting Plate.
Fountains using the Wall Plate Assy. refer to Figure 3
for rough-in dimensions.
2. Shown dimensions pertain to installation location (framing must
support up to 300 lbs. weight). These dimensions are required for
compliance with ANSI Standard A117.0.
3. Install rough-in plumbing as shown in Fig’s. 3 or 5. Run
supply water inlet line through the back panel. Install a service
stop (not provided). Turn on supply water and ush thoroughly.
4. Installing back panel.
Ftn. w/MPW Mounting Plate: Refer to Fig. 16 for placement
of braces onto back panel. Place the upper edge of the panel
above the hanger bracket. Slide the panel down until it engages
the hanger bracket. Be sure back panel is rmly engaged before
releasing it.
Ftn. w/Wall Plate Assy.: Place the upper edge of the panel
above mounting plate on the wall. Slide the panel down until it
engages the mounting plate. Be sure back panel is rmly engaged
before releasing it. (See Figure 9)
5. Install fountain. Remove screw (Item 10) from cover
plate and slide cover plate (Item 14) toward basin. (See Figure 10)
Ftn. w/MPW Mounting Plate: Mount the fountain to the back
panel and wall using (4) 5/16” x 6” long threaded rods, washers,
and nuts (provided). Tighten securely.
Ftn. w/Wall Plate Assy.: Mount the fountain to the back panel
and wall plate assy. with (4) 5/16” x 1” (25mm) long screws
(Item 7 - provided). Tighten securely.
6. Determine required length of waste line and cut to
appropriate length. 1-1/4” O.D. waste tube furnished.
1-1/4” slip trap, waste elbow and extension not provided.
7. Make water supply connections from service stop to the
3/8” O.D. unplated copper tube coming out of the strainer. Turn on
water supply and check for leaks (See Figure 17). Newly installed
water supply line should be insulated after leak check is
completed.
CAUTION: DO NOT SOLDER tubes inserted
into the strainer as damage to the
o-rings may result.
8. These products are designed to operate on 20-105 PSI supply
line pressure. If the inlet pressure is above 105 PSI, a pressure
regulator must be installed in the supply line. Any damage caused
by reason of connecting these products to supply line pressures
lower than 20 PSI or higher than 105 PSI is not covered by
warranty.
9. Check stream height from bubbler. Stream height is factory set at
35 PSI. If supply pressure varies greatly from this, remove push
button (Item 3 - Figure 14) and adjust the screw on the regulator
(Item 18 - Figure 14). To remove push button, remove setscrew
from bottom of sleeve (Item 15). Insert a small punch in screw
hole and push up while grasping the push button and pull forward
removing the push button. Clockwise adjustment will raise stream
height and counterclockwise movement will lower stream height.
For best adjustment stream should hit basin approximately 6-1/2”
from the bubbler. Reassemble the push button by pushing in on
button until the push button catches in the sleeve. Reinstall the
setscrew (Item 6) in the sleeve (Item 15).
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 7
EDFPB114C EDFPBWM114C EDFPBV114C EDFPBWMV114C
97921C (Rev. F - 02/18)
Figure 13 - Fountain Body
Figure 14 - Push Button
15
3
318
18
18
6
5
See Fig. 10 23
11
21
See Fig. 10
12
17
9
13
22
19
14
5
3
Figure 12 - Bubbler Details
NOTE:
When installing replacement bubbler and pedestal, tighten
locknut only to hold parts snug in position. Do Not overtighten.
Basin
1
Locknut
VANDAL RESISTANT
BUBBLER DETAIL
8
Basin
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115

Page 897921C (Rev. F - 02/18)
EDFPB114C, EDFPBWM114C, EDFPBV114C, EDFPBWMV114C
PARTS LIST
ITEM NO. PART NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
NS
56073C
28843C
98871C
55996C
1000001772
75632C
75560C
97446C
38417001
70432C
28708C
28473C
45767C
28343C
45781C
28397C
56092C
98530C
111008343890
AP99
56163C
0000000930
45768C
27089C
Bubbler Assy
Back Panel Assy EDFPBW(V)114C
Kit- Push Button/Spring/Pin/Washer
Strainer
Kit - Elbow 1/4 Stem x 1/4 (3 Pcs) 70817C
Setscrew - #10-32 x .31
Screw - 5/16-18 x 1.00 HHMS
VR Bubbler Assy
Screw - #8-18 x .37 HHSM
Screw - #8-32 x .38 THSM
Basin - Swirlow
Lower Shell
Fountain Body
Cover Plate
Sleeve
Back Panel
Poly Tubing (Cut To Length)
Kit - Regulator/Holder/Nut
Screw - #10-24 x .62 HHMS
AP-99 Panel (Optional)
Gasket - Drain
Assy - Drain/Tailpipe
Plug - Drain 1-1/2”
Hanger Bracket
Figure 17 – Water Supply Connections
TROUBLESHOOTING & MAINTENANCE
Orice Assembly: Mineral deposits on orice
can cause water ow to
spurt or not regulate. Mineral
deposits may be removed from
the orice by poking with a
small round le not over 1/8”
diameter, or using a small
diameter wire.
DO NOT le or cut
orice material.
Stream Regulator: If orice is clean, regulate ow
as in Step 8 of the installation instructions. If replace-
ment is necessary, see parts list for correct regulator
part number.
Actuation of Quick Connect Water Fittings: Cooler
is provided with lead-free
connectors which utilize an
o-ring water seal. To remove
tubing from the tting, relieve
water pressure, push in on
the gray collar while pulling
on the tubing. (See Figure
15) To insert tubing, push
tube straight into tting until
it reaches a positive stop
(approximately 3/4”).
Figure 15 – Quick Connect Fittings
4
2
Installing Back Panel: When installing back panel
assy. (Item 2) with MPW (Mounting Plate), attach
channel braces as shown above. Remove the pro-
tective backing from the tape installed on the braces.
Line up the corresponding holes in the braces and
back panel and press rmly in place.
Figure 16 – Back Panel Assembly
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
NS = NOT SHOWN
WWW.RESTROOMDIRECT.COM 704 • 937 • 2673 129 Oakpark Dr., Unit A, Mooresville, NC 28115