Elkay OBFAVRFR8 1A Series Installation manual

97780C (Rev. G - 11/04)
OBFAVRFR8*1A
Page 1
Installation, Care & Use Manual
Uses HFC-134A Refrigerant
27
5
SEE FIG. 3
719
20, 21,
22,23
24
50
43 49
42
18
46
8, 45
54
6
10 35,36,
48
51 31, 32,
33
34 56 10
25
29
30
55
41,44
38, 39, 40
37
FIG. 1
SEE FIG. 6

OBFAVRFR8*1A
Page 2
97780C (Rev. G - 11/04)
FIG. 2
*ADA REQUIREMENT *REQUISITO DE A.D.A. *EXIGENCEADA
1/4" (6mm) DIA (6 HOLES) 1/4"(6mm) DIAM. (6TROUS) 6AGUJEROSDE1/4"DEDIÁMETRO
FINISHED FLOOR PISO ACABADO PLANCHER FINI
LEGEND/LEYENDA/LÉGENDE A= RECOMMENDED WATER SUPPLYLOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38mm) OUT FROM WALL SHUT OFF BY OTHERS
SERECOMIENDAUBICAR ELTUBOCORTODE CONEXIÓNALTUBODE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT.A1-1/2"(38mm) FUERADELALLAVE DE PASOEN LAPAREDCOLOCADAPOR TERCEROS.
EMPLACEMENTRECOMMANDÉ D'ALIMENTATIONEN EAU PAR TUBE EN CUIVRE NONPLAQUÉDE 3/8 PO. (9,5 mm) D.E. CONNECTANT UNE TUYAUTERIE DE 1-1/2PO.(38mm) DEPUIS LE ROBINETD'ARRÊTFOURNI PARD'AUTRES. B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
UBICACIÓN RECOMENDADAPARAEL DRENAJE DE SALIDADEAGUA, DE 1¼” DE DIÁMETRO. EMPLACEMENTRECOMMANDÉPOUR LE DRAIN DE D.E. 1-1/4" DE SORTIE D’EAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADORDE1¼ NO PROPORCIONADO** SIPHON1-1/4 NON FOURNI**
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX
CAJARECESIVADEALAMBRES(3)DE SUMINISTRO ELÉCTRICO BOÎTEENCASTRÉE D’ALIMENTATIONÉLECTRIQUE(3)FILS
E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGUREUNAVENTILACIÓNADECUADAMANTENIENDO UN ESPACIOE6"(152 mm) (MÍN.) DE HOLGURAENTRELAREJILLADEVENTILACIÓNDELMUEBLEYLAPARED ASSUREZ-VOUSUNEBONNE VENTILATIONENGARDANT 6" (152 mm) (MIN.)ENTRELESÉVENTS DE L’ENCEINTEETLEMUR.
F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
AGUJEROSDE LAS TUERCAS DE7/16PARASUJETAR LAUNIDADALAPARED TROUSD’ÉCROUS7/16 POUR FIXER L’APPAREILAU MUR
RIM HEIGHT
ALTURADE LA
CORONA
HAUTEUR DU
BORD
ORIFICE
HEIGHT
ALTURADEL
ORIFICIO
HAUTEUR DE
L'ORIFICE

97780C (Rev. G - 11/04)
OBFAVRFR8*1A
Page 3
IMPORTANT
ALLSERVICETO BEPERFORMEDBY AN AUTHORIZEDSERVICE PERSON
HANGERBRACKETSAND TRAPINSTALLATION
1) Remove hanger bracket fastened to back of cooler by removing one screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support.
IMPORTANT:
y7-3/4 in. (197mm) dimension from wall to centerline of trap must be maintained for proper fit.
yAnchor hanger securely to wall using all six 1/4 in. dia. mounting holes.
3) Install straight valve for 3/8" O.D. tube.
INSTALLATION OFCOOLER
4) Hang the cooler on the hanger bracket. Be certain the hanger bracket is engaged properly in the slots on the cooler back.
5) Loosen the two screws holding the lower front panel at the bottom of cooler base. Pull front panel forward to gain access inside cooler.
6) Connect water inlet line - See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install them on the cooler water line making sure that the end of the waste line fits into
the trap. Assemble the slip nut and gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, adjust the screw on regulator item 16 by using
a small screwdriver through the small hole in the push button item 2 (See Fig.3). Clockwise adjustment will raise stream and counter-
clockwise adjustment will lower stream. For best adjustment, stream should hit basin approximately 6-1/2" (165mm) from bubbler.
PROTECTFROM HARDFREEZING
9) If the ambient air temperature drops below 0° F, the cooler needs to be drained of all water by blowing out all water lines, evaporator
(item 46), and the drain trap.
3
2
11
52
26
10
9
14
15
47
11
53
16
17
1
WATERFLOWDIRECTION
4
FIG. 3

OBFAVRFR8*1A
Page 4
97780C (Rev. G - 11/04)
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
PRINTED IN U.S.A.
IMPRESO EN LOS E.E.U.U.
IMPRIMÉ AUX É.-U.
PARTS LIST
PARTNO
22897C
45662C
75672C
45663C
35906C
35907C
35909C
27124C
56033C
75500C
70864C
27469C
75566C
40045C
15005C
61313C
50986C
75532C
35900C
30664C
70018C
31490C
70009C
22899C
38417001
27295C
55996C
98118C
62152C
66202C
101516143550
100806740570
19037000
36094C
35959C
35768C
66576C
40614C
50400C
50401C
70444C
21903C
27306C
70016C
31513C
66534C
55931C
36158C
15009C
56092C
26999C
22814C
22822C
22854C
22862C
22955C
100322740560
400660943730
75519C
75520C
75674C
Panel - Bottom Dispenser
Button - Push
Screw - Cap
Sleeve - Push Button
Heater Strip
Switch - Rocker
Heater Thermostat Assy
Cover - Cold Control
Washer
Screw - Torx
Screw - #8 x 5/8” Lg. Torx/Slot
Panel - Screen
Screw - Torx
Hex Nut
Retaining - Nut
Regulator
Holder - Regulator
Screw
Power Cord
Fan Blade
Hex Nut - Fan Blade
Fan Motor
Screw - (Fan Motor)
Shroud - Fan
Screw - #8-18 x 3/8” HHSM
Panel - Front Dispenser
Strainer
Bubbler Assembly
Condenser
Drier
Stud - Compressor Mtg.
Grommet - Compressor Mtg.
Clip - Compressor Mtg.
CompressorServ.PakEMI70 HNR
Relay
Cover - Relay
Heat Exchanger
DrainTube
Gasket - Drain
Ring Support - Drain
Clamp - Drain Gasket
Basin - Stainless Steel
Adaptor - Basin
Hex Nut #10-32
ColdControl
Evaporator Assembly
Cover-Dispenser Bottom Gray
Overload
Bubbler - Nipple
Poly Tubing (Cut To Length)
Cover - Bottom
Panel - LH No Push
Panel- RH No Push
Panel - LH Rear
Panel- RH Rear
Panel - Front Lower
Gasket
Hanger Bracket
Bit - Pinned Torx T-15
Bit - Pinned Torx T-25
Wrench - Allen 7/64
ITEM
NO DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
*34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
NS
NS
NS
NS
*REPLACEWITHSAME COMPRESSORUSED INORIGI-
NALASSEMBLY.
NOTE: All correspondence pertaining to any of the above water
coolers or orders for repair parts MUST include Model No. and
Serial No. of cooler, name and part number of replacement
part.
FOR PARTS, CONTACTYOUR LOCALDISTRIBUTOR OR CALL 1.800.323.0620
PARAPIEZAS, CONTACTEASU DISTRIBUIDORLOCALOLLAMEAL1.800.323.0620
POUROBTENIR DES PIÈCES,CONTACTEZVOTREDISTRIBUTEUR LOCALOU COMPOSEZLE 1.800.323.0620
WARNING!
This unit is frost resistant down to 0° F with no wind. Prevailing
winds can reduce the ability of the heater element to prevent
light freezing. If the ambient air temperature will drop below 0° F,
the cooler needs to be drained of all water by blowing out all
water lines, evaporator (item 49), and the drain trap. A heater
strip is used to heat the unit and will begin to cycle at 40° +/- 5°
F. A check at this temperature will ensure the heater is working
and the unit is resistant to light freezing.
ALSO,MAKESURETHEREARE NO PLASTICORFLAMMABLE
COMPONENTSDIRECTLYABOVE THEHEATERSTRIP.
FIG. 5
1313
12
FIG. 4
FIG. 6
28
57
49
REPAIR SERVICE INFORMATIONTOLLFREE NUMBER 1-800-260-6640
NÚMEROGRATISDE SERVICIO1-800-260-6640
INFORMATIONS POUR LESERVICE PAR NUMERO SANSFRAIS 1-800-260-6640