Elkay VRCTL Series Installation manual

Page 1 1000002232 (Rev. A - 11/14)
VRCTL8*2CQ, LVRCTL8*2CQ
INSTALLATION, CARE & USE MANUAL
Uses HFC-134A refrigerant
VRCTL Series Barrier-Free Water Coolers
TM
NOTE: Non-refrigerated units do not include all electrical and refrigeration components
shown above.
Other components and rough-in are the same as shown.
20
54
42, 43
60
46
1, 4
16
6, 7, 22, 45
See Fig. 5
See Fig. 3
25
25
34
21
19
11
36
35
49
49 9,
21
53
40 (TL)
49 35 8
38 (TL)
57
37
21
59, 39, 41
46
16 16 23, 30,
12, 13
2, 3, 5
1, 4
55
23, 30, 12, 13
54
34
47
58
FIG. 1
60

VRCTL8*2CQ, LVRCTL8*2CQ
Page 2
1000002232 (Rev. A - 11/14)
F
D
F
E
E
2 7/16"
63mm
10"
254mm
5" 127mm
1 1/2"
38mm
A
37 1/2"
952mm
6 1/2"
166mm
ORIFICE
HEIGHT
ALTURA DEL
ORIFICIO
HAUTEUR DE
L'ORIFICE
ORIFICE
HEIGHT
ALTURA DEL
ORIFICIO
HAUTEUR DE
L'ORIFICE
C
L
C
L
1 3/8"
35mm 1 3/8"
35mm
5 3/4"
146mm 5 3/4"
146mm
1 3/8"
35mm 1 3/8"
35mm
5 3/4"
146mm 5 3/4"
146mm
18 1/16"
459mm
FINISHED FLOOR
PISO ACABADO
PLANCHER FINI
5/16" (8mm) DIA. (10 HOLES)
8mm (10 AGUJEROUS)
8mm (10 TROUS)
20 1/8"
511mm
4 1/2"
114mm
6 1/4"
159mm
18 3/4"
476mm
25 1/8"
638mm
B
3 1/2"
89mm
C
RIM HEIGHT
ALTURA DEL
ORIFICIO
HAUTEUR DE
L 'ORIFICE
18 5/8"
474mm
12 5/16"
312mm
4 3/4"
121mm
27"
686mm
31 7/8"
810mm
32 15/16"
837mm
39 1/2"
1003mm
2 5/8"
67mm
8" 203mm
13 7/8"
351mm
20 3/8"
518mm
HANGER BRACKET
FIJADOR DE SUSPENSION
SUPPORT DE SUSPENSION
*6 3/4"
173mm
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB WITH SHUT OFF (BY OTHERS) 3 IN. (76mm) MAXIMUM OUT FROM WALL La UBICACION 3/8 O RECOMENDADA de ABASTECIMIENTO DE AGUA. D. El TUBO del COBRE de UNPLATED CONECTA TALONARIO CON APAGO (POR OTROS) 3 en. (76 Mm) el MAXIMO FUERA DE
PARED
L’O.D de 3/8 d’EMPLACEMENT DE PROVISION D’EAU RECOMMANDE. LE TUBE DE CUIVRE DE UNPLATED CONNECTE STUB AVEC ETEINT (PAR LES AUTRES) 3 dans. (76 mm) le MAXIMUM HORS DU
MUR
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/2” O.D. DRAIN STUB 2 IN. OUT FROM WALL
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1-1/2” DE DIÁMETRO. El TALONARIO 2 FUERA DE PARED EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/2” DE SORTIE D’EAU. STUB 2 HORS DU MUR
C = 1-1/2 TRAP NOT FURNISHED
PURGADOR DE 1-1/2 NO PROPORCIONADO SIPHON 1-1/2 NON FOURNI
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX
CAJA RECESIVA DE ALAMBRES (3) DE SUMINISTRO ELÉCTRICO BOÎTE ENCASTRÉE D’ALIMENTATION ÉLECTRIQUE (3) FILS
E = INSURE PROPER VENTILATION BY MAINTAINING 6” (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 6” (152 mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 6” (152 mm) (MIN.) ENTRE LES ÉVENTS DE L’ENCEINTE ET LE MUR.
F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
AGUJEROS DE LAS TUERCAS DE 7/16 PARA SUJETAR LA UNIDAD A LA PARED TROUS D’ÉCROUS 7/16 POUR FIXER L’APPAREIL AU MUR
FIG. 2
REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDRENS ADA COOLER
** *
ADA REQUIREMENT REQUISITO DE A.D.A. EXIGENCE ADA

Page 3 1000002232 (Rev. A - 11/14)
VRCTL8*2CQ, LVRCTL8*2CQ
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN
AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of
cooler by removing one (1) screw.
2) Mount the hanger bracket and trap as shown
in Figure 2.
NOTE: Hanger Bracket MUST be supported
securely. Add xture support carrier if wall will
not provide adequate support.
IMPORTANT:
• 4 3/4 in. (121mm) dimension from wall to
centerline of trap must be maintained for proper
t.
• Anchor hanger securely to wall using all ve
(5) 1/4 in. dia. mounting holes.
3) Install straight valve for 3/8” O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be
certain the hanger bracket is engaged properly
in the slots on the cooler back as shown in Figure
2.
5) Loosen the two (2) screws holding the lower
front panel at the bottom of cooler base and
two (2) screws at the top (Use torx bits sold
separately). Remove the front panel and set
aside.
6) Connect water inlet line--See Note 4 of General
Instructions.
7) Remove the slip nut and gasket from the trap
and install them on the cooler waste line mak-
ing sure that the end of the waste line ts into
the trap. Assemble the slip nut and gasket to
the trap and tighten securely. Recommend
fastening cooler to wall using 7/16 bolt holes.
(See Fig. 2 “F”)
START UP
Also See General Instructions
8) Stream height is factory set at 45-50 PSI. If
supply pressure varies greatly from this, adjust
screw using the access hole in the pushbutton
(insert screwdriver). CW adjustment will raise
stream and CCW adjustment will lower stream.
For best adjustment, stream should hit basin
approximately 6-1/2” (165mm) from bubbler.
Fig. 3
VANDAL RESISTANT BUBBLER DETAIL
DETALLE DEL GRIFO RESISTENTE AL VANDALISMO
DESCRIPTION DU BARBOTEUR RESISTANT AU VANDALISME
15
1
4
Basin
Estanque
Bassin
1
ITEM
NO.
Filter Assy-1,500 Gal.
Kit-Filter Head Fittings, includes
John Guest 3/8” elbow tting
Assy-Filter & Bracket includes
Fltr Head/Mtg Bkt/John Guest
Fittings/Screws
1
2
3
51299C
98926C
0000000746
DESCRIPTION
PART
NO.
FILTER PARTS LIST
(See Fig. 4)
Fig. 4
3
1
2 2

VRCTL8*2CQ, LVRCTL8*2CQ
Page 4
1000002232 (Rev. A - 11/14)
Fig. 5
(Refrigerated side shown)
30
1
49 (8)
23
15
25
4
40 (TL)
59 31
24 36
50
49
33
34
28
52
48
44
14, 17, 18
26
51
32
56
27
50
50
29
(Items 31 & 24 also
used on the LH unit)
1
50
49
51
12 13
41 39
54

Page 5 1000002232 (Rev. A - 11/14)
VRCTL8*2CQ, LVRCTL8*2CQ
56305C
100806740570
75694C
15009C
19037000
30664C
31431C
35839C
1000002195
35827C
1000002194
160270508640
110868642550
50986C
45866C
56092C
15005C
61313C
66703C
66810C
70002C
70009C
600985451640
28617C
28963C
22897C
45662C
45737C
75672C
100147140560
28596C
28519C
28522C
28516C
22955C
28525C
28528C
28539C
75588C
28536C
75588C
66743C
56237C
40045C
70018C
75524C
55996C
45736C
75570C
75661C
70864C
56033C
66576C
45929C
27124C
55931C
45876C
75583C
56121C
70682C
35826C
75520C
75523C
28551C
Gasket - Bubbler
Grommet - Compressor Mtg.
Stud - Compressor Mtg.
Nipple - Bubbler
Clip - Compressor Mtg.
Fan Blade
Fan Motor
Cold Control
Kit - Elect/Relay/Cover/Overload
Internal Power Cord
Compressor Serv. Pak
Strainer - Bright
Screw - #10-24 x .75 Socket Hd.
Holder - Regulator
Bubbler Assy.
Tubing - Poly (Cut To length)
Retaining Nut
Regulator
Drier
Evaporator Assembly
Screw - #10 x 1/2” Lg. HHSM
Screw - Fan Motor
Drain Plug 1-1/2
Screen - VR
Basin - Stainless Steel
Panel - Bottom Dispenser
Button - Push
Sleeve - Push Button
Cap Screw
Gasket - Drain
Panel - Screen
Panel - RH Dispenser Side
Panel - LH Dispenser Side
Panel - Dispenser Front
Panel - Front Lower
Panel - RH Rear
Panel - LH Rear
Panel - RH Rear TL
Nut - 1-1/4” Slip Joint
Panel - LH Rear TL
Gasket
Condenser
Shroud Fan
Hex Nut
Hex Nut - Fan Blade
Clip (Front & Rear Panels)
Strainer (See “General Instructions”)
Half Nut - Regulator
Screw - #10 x .50 Pinned Torx
Screw - #8 x .50 Pinned Torx
Screw - #8 x .62 Torx/Slot
Washer
Heat Exchanger
Tube - Drain
Cover - Cold Control
Cover - Dispenser Bottom
Drain Tube Assy.
Elbow
Elbow - Drain
Tee 1/4
Power Inlet
Torx Tool - T25
Torx Tool - T20
Hanger Bracket
PART NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Sold Separate
Sold Separate
NS
ITEM NO.
220V-240V/50Hz ITEMIZED PARTS LIST
*
*REPLACE WITH SAME COMPRESSOR USED IN
ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water cool-
ers or orders for repair parts MUST include Model No. and Serial No.
of cooler, name and part number of replacement part.
PRINTED IN U.S.A. FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
ELKAYMANUFACTURINGCOMPANY•2222CAMDENCOURT•OAKBROOK,IL60523•630.574.8484
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
61
10
Fig. 6
220V/240V Detail
Fig. 7
Filter Installation Detail