Elo TouchSystems AMM170TK User manual

AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 1
back of the monitor
ADAVN INTL CORP.2003
ELO is a Registered trademark of Elo TouchSystems, Inc.,
All other trademarks are the ro erty of their reference owners.
This document is subject to change without notice.
Advan rovides this information as reference only. Reference to other vendors roducts
does not im ly any recommendation or endorsement.
Revision Control
WARN IN G
The title "WARNING" is used to inform the users of
possible causes that could inflict the injury, death, or
property damage to the patients.
CAUTION
The title "C AUTIO N " is used to inform the users of
possible causes that could inflict the patients although
it might not severe enough to cause deaths.
NOTE
The title "NOTE" is used to inform the users of items
tha t a re o f imp o r ta nc e in te rms o f ins ta lla tio n,
operation, or maintenance of the Equipment although
the failure does not inflict the bodily harm to the
patients.
Date Description
Document number
Rev. 4 112003

2 Users Guide
TABLE OF CONTENTS
Quick Setup................................................................................... 3~5
Product Features... 6
Unpacking .... 7
Symbol xplanations. 8
Regulatory Compliance. 8
U Declaration of Conformity for Medical Applications......... 9
Screen Position Adjustment... 10
Cleaning lnstructions.. 11
Supported Modes..... 12
Power Management Function 13
Power Management System.. 13
Connecting the Power Cord.. 14
DDC. 14
Installation. 14
Installation for Video Play Back.......................................................15
User Controls... 16
Basic OSD Operation (VGA)... 17~18
Basic OSD Operation (DVI)... 19~20
Basic OSD Screen Section (C-Video or S-Video).... 21~22
OSD Function Description (VGA) 23
OSD Function Description (DVI) 24
OSD Function Description (C-Video or S-Video)........... 25
Troubleshooting 26
Specification of AMM17TK......................................................... 27
Specification of AMM18TK......................................................... 28
Specification of AMM19TK......................................................... 29
Connectors... 30
Description of Warranty 31~32
Tounchscreen Users Manual ... 33~34

AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 3
Quick Setup (IBM/IBM Compatible under Windows 95/98/ME/ 000)
Please Read Carefully When Setting Up Your New Monitor
Monitor Screen Adjustment and Resolution Setting Procedure for IBM/IBM Com atible
Com uters with Windows based OS system.
Before adjusting the monitor, all the necessary drivers should be installed to your System
and resolution has to be set to manufacturers recommended reset of 1280 x 1024 @ 60Hz,
70Hz, 72Hz or 75 Hz.
To check the resolution, ress the SELECT UP button on the monitor and the In ormation
will dis lay under the OSD. Information will have Resolution, Horizontal and Vertical (Refresh
rate) frequency information.
To change the resolution to its actory recommended preset.
1. On a Windows 95, 98, ME or 2000, ress right button on a Mouse to execute the Po -u
menu.
2. Press Properties to execute the Display Properties
3. Press Setting and change the resolution to 1280 x 1024.
4. Press Apply or OK to select and ress OK to kee the selected resolution.
5. Go back to Display Properties - Setting - Advanced properties - Adapter
6. On Ada ter ro erty, change the refresh rate to 60Hz, 70Hz, 72Hz or 75Hz. If you dont
have these o tions, choose Adapter De ault. (60Hz recommended)
Screen Adjustment Procedure
1. Press the AUTO button.
2. If you still dont have a clear dis lay monitor, lease refer to ste 3.
3. Start Shut Down in Windows 95/98/ME/2000 - It will dis lay moire on screen
4. Press Up or Down button then the OSD menu will o -u .
5. Adjust the Frequency under the OSD to reduce or get rid of the vertical dis lay noise
(Jail bars). (Page 16)
6. Once the vertical dis lay noise disa ears, ress adjust the Phase to reduce or get rid of
the horizontal dis lay noise (Snowy effect). (Page 16)

4 Users Guide
Quick Setup (IBM/IBM Compatible under Windows NT 4.0)
Please Read Carefully When Setting Up Your New Monitor
Monitor Screen Adjustment and Resolution Setting Procedure for IBM/IBM Com atible
Com uters with Windows based OS system.
Before adjusting the monitor, all the necessary drivers should be installed to your System
and resolution has to be set to manufactures recommended reset of 1280 x 1024 @ 60Hz,
70Hz, 72Hz or 75Hz.
To check the resolution, ress the SELECT UP button on the monitor and the In ormation
will dis lay under the OSD. Information will have Resolution, Horizontal and Vertical (Refresh
rate) frequency information.
To change the resolution to its actory recommended preset.
1. On a Windows NT 4.0, ress right button on a Mouse to execute the Po -u menu.
2. Press Properties to execute the Display Properties
3. Press Setting and change the resolution to 1280 x 1024.
4. Change Re resh Frequency to 60Hz, 70Hz, 72Hz or 75Hz. (60Hz recommended)
Screen Adjustment Procedure
1. Press the AUTO button.
2. If you still dont have a clear dis lay monitor, lease refer to ste 3.
3. Start Shut Down in Windows 95/98/ME/2000 - It will dis lay moire on screen
4. Press Up or Down button then the OSD menu will o -u .
5. Adjust the Frequency under the OSD to reduce or get rid of the vertical dis lay noise
(Jail bars). (Page 16)
6. Once the vertical dis lay noise disa ears, ress adjust the Phase to reduce or get rid of
the horizontal dis lay noise (Snowy effect). (Page 16)

AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 5
Quick Setup (Macintosh)
Please Read Carefully When Setting Up Your New Monitor
1. Set your Macintosh Ada ter on ages 23 and 24.
2. Push the APPLE icon on the u er left corn and execute Control Panel->
Monitors&Sound. Select Thousands for the Color De th, Select 1280X1024, 60Hz,
70Hz, 72Hz or 75Hz for the Resolution. (60Hz recommended)
* On some A le G3 or newer systems, you may not need to use the Macintosh Ada ter.
Screen Adjustment Procedure
1. Press the AUTO button on the monitor.

6 Users Guide
INTRODUCTION
Congratulations on your urchasing of the AMM17TK/AMM18TK/AMM19TK high
erformance TFT LCD monitor.
FEATURES
The FPD is a TFT-LCD monitor that is intelligent, micro rocessor-based and ergonomically
designed dis lay, com atible with most analog RGB (Red, Green, Blue) dis lay standards,
including PS/V, PS/2, A le Macintosh Centris, Quadra, and Macintosh II family signals. The
LCD monitor is ca able of dis laying cris and vibrant color gra hics with VGA, SVGA, XGA,
SXGA (non-interlaced), and most Macintosh com atible color video cards.
•Advanced Viewing Solution (AVS): Our so histicated filter extends the viewing angle of
the screen image, without sacrificing contrast ratio and brightness.
•Advanced Timing Setup (ATS): A unique technology from the One Touch Auto Adjustment.
Pressing the Auto Adjust button on the front anel, automatically o timizes osition,
hase, clock, contrast and color balance. This allows the user to maximize the erfect
screen setting in the shortest amount of time.
•Advanced Mounting Solution (AMS): Im rove flat anel environment, utilizing numerous
ergonomic mounting solutions to allow creative use in conjunction to roduct a lication.
•The monitor is able to ro erly function even in case of u grade video cards or software
because of the wide auto-scanning com atibility range without requiring to buy a new
monitor.
•The internal micro rocessor digitally controls auto-scanning. For horizontal scan
frequencies between 24.8 KHz and 60.2 KHz, and vertical scan frequencies between
56.3 Hz and 85.1 Hz. In each frequency mode, the micro rocessor-based circuitry allows
the monitor to function at the recision-of a fixed frequency.
•The resident memory allows for storing factory default settings and also additional user
adjustment arameters.
•The maximum resolution achievable is SXGA (1280 x 1024), best suited for Windows
a lications
•The com act and sleek cabinet design saves lot of your desk s ace and makes your desk
look neat and tidy.
•The monitor is com liant with VESA-DPMS ower management standard. In order to
save energy, the monitor must be connected to a system com liant with the standard.
•The monitor is also com liant with the most stringent environmental scheme of TCO
95. In this scheme, no environmental harmful substances are used during the entire
manufacturing rocess.
The monitor is certified by UL International to medical standard UL2601-1. It is also CE
marked for sale into the Euro ean Community for integration or use with medical roducts. It
is certified by NEMKO according to EN60601-1 & EN60601-1-2 for sale to the medical market.

AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 7
UNPACKING
Please check the following items are resent when you un ack the box, and save the acking
materials in case you will need to shi or trans ort the monitor in future.
•AMM17TK, AMM18TK, AMM19TK or AMM19TK/HB LCD Monitor and two video
cable (1) VGA HDDB15 cable (1) DVI-D cable
•AC Power cord
•AC-Ada ter
•Flo y Disk (for test attern and set u )
•User Manual
•Com osite Video (C-Video) Cable and Su er Video (S-Video) Cable *Some Touchscreen
Model Not Available
AUTO
SELECT
CAUTION
Manufacturer : Ault Korea
Model No : MW160 or MW116

8 Users Guide
Symbol Explanations
This monitor is intended for use in Health Care Facilities.
Regulatory Compliance
This monitor has been tested to com ly with IEC/EN 60601-1 and IEC/EN60601-1-2
By NEMKO and is certified by UL to medical standard UL2601-1(UL/cUL Mark).
Because many medical offices are located in residential areas, this monitor, in addition to the
medical requirements, has also been tested and found to com ly with the limits for FCC Class
B com uting devices in a ty ically configured system. It is the system integrator or
configurers res onsibility to test and ensure that the entire system com lies with a licable
EMC laws.

AMM170TK/AMM17TK/AMM18TK/AMM19TK/AMM19TK(HB) 9
EU Declaration of Conformity for Medical Applications
A Declaration of Conformity has been filed for this product. A sample of this
document may be found in the addendum which accompanied this manual. For a
copy of the Declaration of Conformity document, please contact ADVAN Intl
Corp. and request for A 17TK, AG 18TK, A 19TK and
A 19TK/HB DOC.
Installation
Before you unpack your monitor, prepare a suitable workspace. You need a stable
and level surface near a grounded wall outlet in an area which is relatively free of
glare from sunlight or other sources of bright light. The monitor is cooled by natural
convection (it has no fan).
For optimum performance, do not block the cooling vents.
While unpacking the monitor, inspect it and other package contents for shipping
damage that could cause a fire or shock hazard. Immediately report any shipping
damage to the carrier or transportation company and contact customer service for
monitor in the future or in case of return.
After you unpack the monitor, make sure the following items are included
 onitor with 1.5 meter(5ft)monitor-to computer video cable
 AC adapter with cable
CAUTION: AC Ada ter must be lugged into Grounded a ower outlet)
CAUTION : AC ada ter
Manufacturer: Ault korea
Model No: MW160 or MW116
 Touchscreen cable if monitor has touchscreen o tion
 This o erations manual
Note: Your system provider may offer alternative cords or cables
depending on the installation requirement and local geography issues.

10 Users Guide
SCREEN POSITION ADJUSTMENT
In order to o timize the best viewing osition, you can adjust the tilt of the monitor by using
both of your hands to hold the edges of the monitor as shown in the figure below. The moni-
tor can be adjusted to 28 degrees u as indicated by arrow below.
28°
Equi ment is not suitable for use in the resence of a flammable anesthetic mixture with air or
with oxygen or nitrous oxide.
No user serviceable arts inside, ask qualified ersonnel when accessing inside
For dis osal of waste roduct, you must follow the requirement of local code.
Electrical in ut rating : 12V d.c. 6.67 A
Classification
- Ty e of rotection against electric shock: ClassI Equi ment
- Degree of rotection against the ingress of water: Ordinary
- Mode of o eration: Continuous
Environmental conditions for trans ort and storage:
- Tem erature range within 20 oC to 60 oC
- Relative humidity range within 10% to 90%
- Atmos heric ressure range within 500 to 1060 hPa.