Elo TouchSystems ET1302L-2UWA-1-BL-G User manual

3
USER MANUAL
Elo Touch Solutions
ET1302L
UM600243 Rev A

User Manual ET1302L
2
Copyright © 2019 Elo Touch Solutions, Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or
by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) make no representations or warranties
with respect to the contents herein, and specifically disclaim any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to revise
this publication and to make changes from time to time in the content hereof without obligation of Elo to notify any person of such revisions or changes.
Trademark Acknowledgments
Elo, Elo (logo), Elo Touch, Elo Touch Solutions and TouchPro are trademarks of Elo and its Affiliates. Windows is a trademark of Microsoft Corporation.

User Manual ET1302L
3
Table of Contents
Section 1: Introduction ............................................................................................................................................................................................................................... 4
Section 2: Installation................................................................................................................................................................................................................................. 5
Section 3: Mounting ................................................................................................................................................................................................................................... 9
Section 4: Operation ................................................................................................................................................................................................................................ 12
Section 5: Technical Support................................................................................................................................................................................................................... 15
Section 6: Safety & Maintenance............................................................................................................................................................................................................. 17
Section 7: Regulatory Information............................................................................................................................................................................................................ 18
Section 8: Warranty Information............................................................................................................................................................................................................... 25

User Manual ET1302L
4
Section 1: Introduction
Product Description
Your new touch monitor combines the latest developments in touch technology and display design with reliability for use in high-traffic environments.
This touch monitor incorporates a 24-bit color, active matrix thin-film-transistor LCD panel to provide high-quality display performance. ET1302L supports
full HD 1920 x 1080. Its LED backlight significantly reduces power consumption and eliminates the need for mercury (compared to CCFL-backlit panels).
Other features that enhance this LCD monitor’s performance are USB Type-C (display, touch and video), Plug & Play compatibility, remote on-screen
display (OSD) controls and flexible mounting options.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user manual to maximize the life of your unit and prevent risks to user safety.
See the Safety & Maintenance Section for more information.
This manual contains information that is important for the proper setup and maintenance of the unit. Before setting up and powering on your new touch
monitor, read through this manual, especially the Installation, Mounting, and Operation Sections.

User Manual ET1302L
5
Section 2: Installation
Unpacking the Touch Monitor
Open the carton and verify that the following items are present:
• Touch monitor with stand: E683204 (or without stand: E683595)
• Quick Install Guide
• HDMI cable
• Touch USB Cable (USB Type-A to Type-C)
• Power brick
• Europe power cord
• North America power cord
• EEI Label
• 3 x tie wraps
• 2 x cable cover screws

User Manual ET1302L
6
Connector Panel
Note: Cable tie-down points can be used to tie down the cables with tie wraps. Simply loop the tie wraps through the cable tie-down points and around the
cable to secure cable connections.
Touch Monitor Connections
Source without USB Type-C Power Delivery function:
1. Connect one end of the HDMI or VGA-DB15-to-MICRO cable (sold separately Elo P/N: E710549) to the
monitor’s HDMI/VGA input connector and the other end to yourHDMI/VGA video source (tighten the
video cable’s screws on the VGA connector for best performance).
2. Connect the USB touch cable (USB Type-A to Type-C) between the monitor’s USB-C connector and your PC’s USB port.
3. Connect the audio cable between the monitor’s Audio line-in and your audio source (you can also use built-in audio via your HDMI cable)
4. Connect the power adaptor’s input connector to the power source. Connect the power adaptor’s DC output connector to the monitor’s input power jack.
5. The touch monitor ships in an OFF state. Press the power button to turn it on.
Source with USB Type-C (W/O Power Delivery function):
1. Connect the USB Type-C to Type-C cable (sold separately Elo P/N: E710364) between the monitor’s USB-C connector and your PC’s USB port. Connect the.
2. Connect the power adaptor’s input connector to the power source. Connect the power adaptor’s DC output connector to the monitor’s input power jack.
3. The touch monitor ships in an OFF state. Press the power button to turn it on.
USB Type-C for everything - Source with USB Type-C (w/ Power Delivery function 15V 1.8A / 20V 1.35A):
1. Connect the USB Type-C to Type-C cable (sold separately Elo P/N: E710364) between the monitor’s USB-C connector and your PC’s USB Type-C port.

User Manual ET1302L
7
2. The touch monitor ships in an OFF state. Press the power button to turn it on.
This USB type C monitor is powered by USB port which complies with LPS and SELV circuit according to IEC 60950-1:2005, or complies with ES1 and PS2 circuit
according to IEC 62368-1:2014.

User Manual ET1302L
8
Installing Touch Technology Software Drivers
No additional drivers are required for your projected-capacitive touch monitor with Windows 7, Windows 10 and most versions of Mac OS X, Android or
Linux as it will use the built-in HID drivers in the Operating System. If the monitor is used with the Windows XP operating system, follow the steps below
to install the Windows XP touch driver.
To download the latest touch drivers:
1. Visit www.elotouch.com/Support/Downloads/Driver/DriverDownload/Default.aspx
2. Select the “Touch Drivers” from “Product Category” dropdown menu.
3. Select the operating system from “Operating System” dropdown menu.
4. Click on the driver version required for your touchscreen display.

User Manual ET1302L
9
Section 3: Mounting
Rear VESA Mount
A four-hole 75 x 75 mm mounting interface for M4 screws is provided on the rear of the monitor. Remove the stand using a Phillips screwdriver to access
the mounting interface. The VESA FDMI-compliant counting is coded VESA MIS-D, 75, C.

User Manual ET1302L
10
Base Mount
ET1302L base mounting options are shown below.