ELRO AS90CA User manual

jK
AS90CA Manual EN Version 3
USER MANUAL
HD PAN/TILT SECURITY CAMERA
ACCESSORY HOME+ ALARM SYSTEM
Home is not a place, it’s a feeling
AS90CA

- 1 -
Inhoud
1. Introduction ................................................................................................- 2 -
2. Package Contents........................................................................................- 2 -
3. Installation Android.....................................................................................- 3 -
4. Explanation icons ........................................................................................- 6 -
5. Deleting a connection .................................................................................- 6 -
6. Motion detection and recording.................................................................- 6 -
7. Playback recordings ....................................................................................- 6 -
8. Horizontal/vertical rotation ........................................................................- 7 -
9. Reset ...........................................................................................................- 7 -
10. Frequently asked questions........................................................................- 7 -
11. Specifications ..............................................................................................- 8 -
12. DoC..............................................................................................................- 9 -

- 2 -
1. Introduction
Please take the time to read this manual before you start installing and assembling the security
camera. The camera is equipped with a speaker and microphone. You can communicate via the
app on your smartphone with the persons within hearing range of the camera. The camera has
6 IR LEDs for excellent night vision. With the pan/tilt/zoom function, you can remotely scan the
room where the camera is placed.
2. Package Contents
•The security camera (1) is supplied with:
•Adapter DC 5V/1A with 1.4 m cable (2)
•Network cable 1 m, do not use during installation (3)
•Handy mounting bracket + mounting template (4)
•Screws and plugs (5)

- 3 -
3. Installation Android
The camera installation must be carried out WITHOUT network cable.
After installation and if needed for a more stable connection, you can connect the camera with
a network cable to your router/modem
•Connect the adapter to the camera and a wall outlet, do not connect the network cable.
•Wait for about 1 minute for the camera to perform a self-test, the camera will start running.
•Open the app and tap "Add accessories" (1).
•Scan the QR Code on the bottom of the camera (2).
•Connect your smartphone to the camera's network, tap the blue bar (3).
•When prompted, enter the camera's default password: 01234567.
•The camera's network IPcam***870-TLUSN (4) will now be visible in the WiFi list, tap it
(Installation with Android tablet see page 5).
•Your smartphone is paired with the camera (5) (Installation with Android tablet see page 5).
•The camera is now not connected to the internet, only to your smartphone.
•Return to the WiFi list (6) (Installation with Android tablet see page 5).
•Choose your own network, refresh (7) if the network is not yet visible.
•Once your own network has been set up, press the blue "V" (8) to confirm.
•You can now give the camera a (location) name (9), click the blue "V" to agree.
•Now tap the Smart Camera icon (10).
•The camera will come online, tap the circle with the exclamation mark (11).
•You will now be asked to change the password "admin" (12).
•Change the password and confirm (13), the camera is now successfully connected (14).
ADVICE: In case of an unstable network, you can connect a network cable to the camera and
your router/modem after installation.

- 4 -

- 5 -

- 6 -
4. Explanation icons
In this menu, you can point and zoom (4x) the camera.
Tap to take a photo.
Tap to listen.
Press and hold to talk.
5. Deleting a connection
The link can be removed by tapping on the location name "Living
Room" in the "Smart Camera" screen (14). You will then enter the
"Accessory Settings" screen (15) and remove the link by tapping
"Delete" (16).
6. Motion detection and recording
A micro SD card of up to 128GB can be inserted. All recordings
registered by the motion detection are stored on it. The
recording lasts 15 seconds. Tap "Camera settings" (17) and then
"Motion detection and recording" (18) to make settings (19).
For retrieval of recordings, it is
important that the camera is set
equal to the time on your
phone, select this option (20)
and agree. Format the SD card
before using it (21).
7. Playback recordings
When you start playback, recordings are retrieved from the SD
card, please note that this may take a while. The camera always
overwrites the oldest recordings. If you need to save recordings,
you can copy the contents of the SD card to your PC or laptop.
Recordings are recorded in (22)HD (high definition) by default.
HD switched off is SD (standard definition).

- 7 -
8. Horizontal/vertical rotation
These functions (23)allow you to correct the image in the app horizontally and vertically.
9. Reset
•This returns the camera to its factory settings. No network cable should be connected and a
previous connection must be removed, see chapter 4 Removing a connection.
•Use the tip of a pencil/ballpoint pen or a paperclip to poke the hole (24)and hold it down for
around 10 seconds. You will hear a beep and the camera will perform a self-test (pan/tilt
function).
•Some time may pass before all data is deleted. Remove the mains adapter from the camera
and wait for around 1 minute before reinserting it. Wait until the camera has completed the
self-test and then reset the camera again.
10.Frequently asked questions
The camera is connected to the Internet but I cannot connect it in the app.
•The installation must be carried out without a network cable.
•Make sure you have used the correct QR code during the pairing section.
•Make sure you are using 2.4GHz Wi-Fi, the camera cannot support 5GHz yet.
•The camera only supports IPV4. DHCP Server/Services must be enabled on the router setting.
•If you are using a firewall, all ports from 10000 to 65535 of the camera's IP address must be
allowed to go in/out in the firewall rule. We recommend that you allow the camera for all data.
I cannot save the screenshots.
•The app needs to access your phone's album to save the screenshots. You may need to
approve the authorisation. If you incorrectly click the 'No' option during authorisation, you may
need to enable it in the system menu.
I am unable to pair the camera with an iOS smartphone.
•Please try the installation with an Android smartphone/tablet. After installation, the camera
will automatically be available for your iOS device.
There is a lot of delay, during the Pan/Tilt function the image moves jerkily forward.
•If you have an unstable network, you can connect a network cable to the camera and your
router/modem after installation.
The camera regularly emits an audio signal.
•This may indicate a restored WiFi signal. Make a permanent connection with a network cable
to your router/modem.

- 8 -
11.Specifications
Camera
Image sensor
1/2.7" 2MP CMOS
Effective pixels
1920(H)x1080(V)
WDR (contrast)
Digital WDR
Noise Reduction
3D DNR
Light sensor
(IR-Cut) Auto (ICR) / Colour / Black & White
IR distance
9 metres (30 ft)
Supported SD Card (excl.)
Max. 128 GB
Lens
Focal length
4 mm
Aperture
F2.1
Focus
Fixed
Angle of View
90°
Audio
Intercom
2-way
Encoding
G711/G726
Interface
Microphone Enclosed
Video
Encoding
H.264 Ma in/Baseline profile
Resolution
1080P (1920X1080) 720P (1280x720)
Video Bitrates
32Kbps ~ 8Mbps
Video Frame Rate
15fps@1080P
Netwerk
Ethernet
RJ-45 (10/100Base-T)
Networkprotocol
HTTP, FTP, TCP/IP, UDP, SMTP, DHCP, NTP, UPNP, RTSP,
Onvif, DDNS
WDR (contrast)
Digital WDR
Smartphone
Android (2.3 of hoger) - iOS (5.0 of hoger)
WiFi
(802.11b/g/n), alleen 2.4G
Only supports WEP/WPA-PSK/WPA2-PSK-encryptie
P2P
Supported
Algemeen
Wireless distance
up to 50m (unobstructed)
Power supply
DC 5V/1A
Power Consumption
<5W
Operating temperature
-10°C~+60°C,10%~90% RH
Dimensions
177 x 141 x 117mm
Weight
650 gram

- 9 -
12.DoC
-I, ELRO Europe, hereby declare that the radio equipment type AS90CA conforms to
Directive 2014/53/EU. The full text of the EU Declaration of Conformity can be found at the
following internet address: www.elro.eu/compliance"
-Frequency: 2.4GHz-2.4835GHz
-Maximum transmitting power: 19dBm
Symbols
Recycling and Disposal: The WEEE symbol means that this product and batteries must be
disposed of separately from household waste. When this product reaches the end of its
life, take it to a designated waste collection point nearby to ensure safe disposal or
recycling. Protect environment and public health, handle natural resources responsibly!
Read the manual before use and keep it in a safe place for future use and maintenance.
Warranty visit www.elro.eu
ELRO Europe | www.elro.eu
Postbus 9607 - Box E800
1006 GC Amsterdam - The Netherlands