ELRO C935IP User manual

Wireless APP Camera
Installation and Operating Instructions
C935IP
Version 1.0
PLEASE READTHESE INSTRUCTIONSCAREFULLY BEFOREUSINGTHISPRODUCT
AND KEEP THIS MANUAL FOR FUTURE REFERENCE.

The state of art WAPP camera is capable of deliver high quality Digital High
Definition (HD) video to your smart-mobile device(s) which would require
higher internet bandwidth. Due to your local internet environment condition
your mobile device(s) may display black-screen or temporary disconnect to
the WAPP camera.
Make sure the WAPP camera is operating with sufficient internet
bandwidth 1Mbps (upload/download speed) is suggested.
For best performance the smart-mobile device(s) need to be on Wi-Fi
or 4G mobile network in order to receive maximum download speed.
When the internet transmission is low your WAPP APP will
automatically switch to Relay Mode:
By adjusting to “Better Streaming” in the system setting section
may improve the WAPP APP performance.
Your internet bandwidth is limited. For best performance try to avoid
more than two users connecting to the WAPP camera simultaneously.
Make sure your smart-mobile device(s) is equipped with up-to-date
technology 1.5GHz dual core processor or equivalent is suggested.
If the signal strength of your Wi-Fi router is weak there are several
ways to improve transmission:
Change router/camera relative position to receive better signal.
Use wire Ethernet cable on the WAPP camera to establish
connection between WAPP camera and your router.
Use Wi-Fi repeater/extender to maximize the service range of
your Wi-Fi route.
Switch your router to 11b/11g mode in order to improve router
service range.
Purchase extension cable or high gain antenna for your camera
from the WAPP vendor.
Please make sure the memory card used is CLASS10 rated.

1
CONTENTS
INTRODUCTION .............................................................................................................2
WIRELESS DEVICES OPERATING RANGE ..................................................................2
IMPORTANT SAFETY PRECAUTIONS ....................................................................... 2
KIT CONTENT .............................................................................................................................. 4
SAFETY AND INSTALLATION TIPS ....................................................................................... 5
NIGHT VISION .......................................................................................................6
CAMERA INSTALLATION ....................................................................................................6
CAMERA OVERVIEW ................................................................................................................ 6
DOWNLOAD AND SETUP THE APP............................................................................8
LIVE VIEW / SNAPSHOT / RECORDING .............................................................. 11
VIEWING YOUR SNAPSHOTS ........................................................................................12
PLAYBACK YOUR VIDEOS ..................................................................................................... 12
MAIN PAGE OVERVIEW ......................................................................................................... 16
ADVANCED SETTING .......................................................................................................21
ADMIN PASSWORD..................................................................................................22
EMAIL ALERT ................................................................................................................................. 22
TIME ZONE.................................................................................................................23
DAYLIGHT SAVING ..............................................................................................................23
DEVICE SECURITY CODE .................................................................................................23
VIDEO SETTINGS ........................................................................................................... 23
WI-FI SETTING ................................................................................................................ 24
SENSITIVITY SETTING ................................................................................................. 25
EMAIL SETTING ............................................................................................................. 25
SD CARD SETTING ......................................................................................................... 26
OVERWRITE SD CARD .................................................................................................. 26
PROFILE SETTING ......................................................................................................... 26
DEVICE INFORMATION.........................................................................................26
PRODUCTION SPECIFICATION ....................................................................................30
STORAGE MEDIA MANAGEMENT...............................................................................31

2
INTRODUCTION
PLEASE READ BEFORE YOU START
Always use discretion when installing CCTV equipment, especially when there is
perceived policy. Enquire relevant local regulations applicable to the lawful installation
of video recording/surveillance. Third party consent may be required.
WIRELESS DEVICES OPERATING RANGE
Ensure the signal reception viewed from the wireless camera(s) is the best possible
reception between the camera(s) and the Wi-Fi router. If necessary, reduce the
distance between the camera(s) and the Wi-Fi router to improve overall system
performance. Wireless Color Camera Recordable CCTV Kit operating on a secure
digital 2.4GHz frequency which could greatly reduce interference from product such
as wireless routers, cordless phones or microwave ovens.
IMPORTANT SAFETY PRECAUTIONS
Damages caused by non-compliance with this operating manual will void the warranty!
We will not assume any liability for damages to items or persons caused by improper
handling or non-compliance with the safety notices! Any warranty claim will be null and
void in such cases.
1. Do not drop, puncture or disassemble the camera; otherwise the warranty will be
voided.
2. Avoid all contact with water, and dry hands before using.
3. Never tug on the power cords. Use the plug to unplug it from the wall outlet.
4. Do not expose the camera to high temperature or leave it in direct sunlight. Doing so
may damage the camera or cause camera temporary malfunction.
5. Use the devices with care. Avoid pressing hard on the camera body.
6. For your own safety, avoid using the camera or power off the camera when there is a
storm or lightning.
7. Remove the power adapter during long periods between usages.
8. Use only the accessories and power adapters supplied by the manufacturer.
9. To meet the regulations pertaining to parental responsibility, keep the devices out of
the reach of infants.
10. Check power cables, do not get crushed or damaged by sharp edges whenever the
devices are in operation.

3
FCC Compliance Statement: This
device complies with Part 15 of the
FCC rules. Operation is subjected
to the following two conditions: (1)
this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Products with CE Marking comply with
EMC Directive (2004/108/EC); Low
Voltage Directive (73/23/EEC);
R&TTE(1999/5/EC); ROHS Directive
(2011/65/EU) issued by the Commission of the
European Community. Compliance with these
directives implies conformity to the following
European Norms: EMC: EN 301 489
LVD: EN 60950
Radio: EN 300 328
FCC/CE WARNING
This equipment has been tested and found to comply with limits for a Class B digital
device, pursuant to Part 15 of the FCC rules and ETSI(EN) 300328. These limits are
designed to provide reasonable protection against harmful interference in residential
installations. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does interference to radio or
television equipment reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures: -Reorient or relocate the receiving antenna.-Move the equipment
away from the receiver.-Plug the equipment into an outlet on a circuit different from that
to which the receiver is connected.-Consult the dealer or an experienced radio/television
technician for additional suggestions. You are cautioned that any change or modifications
to the equipment not expressly approved by the party responsible for compliance could
void your authority to operate such equipment.
DISPOSAL
If the camera system no longer functions or can no longer be repaired, it
must be disposed of according to the valid statutory regulations. Disposal
of spent batteries/accumulators:
You are required by law (Battery Ordinance) to return all spent batteries
and accumulators. Disposing of spent batteries/accumulators with common household
waste is prohibited! Batteries/accumulators that contain hazardous substances are marked
with the symbols on the side. These symbols indicate that it is prohibited to dispose of
these batteries/accumulators in the household waste. The abbreviations for the respective
heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead. You can return spent batteries and
accumulators that can no longer be charged to the designated collection points in your
community, outlets or wherever batteries or accumulators are sold. Following these
instructions will allow you to fulfill the legal requirements and contribute to the protection
of our environment!

B
Camera Stand x 1
D Power Adapter x 1
F Rj45 Connect Jack x 1
F
Quick Start Guide x 1
KIT CONTENT
A
Wireless App Camera x 1
C Camera Antenna x 1
E Screw Pack x 1
G
Manual CD x 1
Tools Required:
Electric drill
5mm masonry drill bit
15mm masonry drill bit
No. 2 Philips screwdriver
For best system performance:
-iOS: iPhone4S / iPad2 / Mini iPad or above. Maximum 12 registered camera
connections.
-Android: 1.5G dual core processor or above / 960*540 pixel or above. Maximum 12
registered camera connections.
-Storage: Class 10 memory card.
-Bandwidth: 1Mbps or above upload/download speed suggested.

SAFETY AND INSTALLATION TIPS
Do not attempt to open the units with the power adaptor plug connected to
avoid any risk of personal injury.
When installing CCTV camera(s), always follow manufacturer's advice
when using power tools, steps, ladders, etc. and wear suitable protective
equipment (e.g. safety goggles) when drilling holes. Before drilling holes
through walls, check for hidden electricity cables and water pipes. The use
of cable/pipe detector is advisable.
It is also advisable to avoid exposing any cameras to extreme weather
conditions (e.g., under a gutter which is prone to any water leaks). When
installing any cameras with this unit, it is advisable to use cable conduit to
protect any video/power extension cables from being exposed externally
and to prevent/reduce the chances of the cables being tampered with. After
drilling any hole though an external wall for a cable, ensure the hole is
sealed up around the cable using a sealant to prevent drafts.
To prevent a fire or electrical shock hazard, do not attempt to open the
housing while the unit is exposed to rain, water or wet conditions. There
are no user serviceable parts inside. Refer servicing to qualified service
personnel. Avoid pointing the camera(s) directly at the sun or any bushes,
tree branches or moving objects that might unnecessarily cause the camera
to record.
5

NIGHTVISION
The camera has built-in infrared LEDs to allow you to view at night for
24-hour surveillance. The LEDs will automatically activate at night and the
picture viewed will turn to black and white. The night viewing range is up
to 5 meters.
CAMERA INSTALLATION
Secure camera stand on the
stable surface.
Loosen up the Thumb screw.
Adjust proper view angle then
secure the joint with T-bolt.
Ceiling Mount Wall Mount
6

CAMERA OVERVIEW
Antenna
Power Indicator
Signal Indicator
SD Card Slot
PIR Infrared LEDs
Stand
RJ-45 Cable
Power Cable
7

8
DOWNLOAD AND SETUP THE APP
The Wireless APP camera is designed todeliver live video footage directly
to your smart phone or tablet device. Please follow these steps to download,
setup and use the APP.
APP Name: OMGuard HD
Download the App
1. From you smart phone or tablet device, click the APP Store/Google Play
and search for “OMGuard HD”.
2. Once located the APP, select download.
3. Once download completed, you will find the APP icon on your mobile
device screen.
APP Setup
△
! BEFOREYOUSTART
Before connecting the camera to power source, first connect the camera to your
Wi-Fi router by using only the Ethernet cable provided.
After the camera is connected to the Wi-Fi router, connect the camera to power
source and wait until both RED and GREEN LED begin flashing. DO NOT begin
the setup process until both LEDs become steady on (roughly 45 seconds).
Please follow the steps in the following pages to complete the setup.

9
1. Make sure the mobile device you are using is connected to the same
Wi-Fi router the camera is connected to.
2. Locate the “OMGuard HD” icon in your mobile device and launch the
App.
3. Tap the ADD CAMERA icon to add a new camera. Then click
the SEARCH button for a quick setup. The APP will search available
camera(s) connecting to the Wi-Fi router and display the camera
information in the pop up list. Select the camera from the list and the
APP will automatically add the camera’s DID code to the DID column.
Enter the default password 123456.
(iOS) (Android)
Note: After you have entered the default password, the APP will remind you to
change the default password.
4. Click SAVE to complete the camera settings. The system confirms the
user identity and grants permission to user access.
5. You can refer to "ADD CAMERA" section for detail on adding additional
camera(s).

10
In most cases, you can successfully add the camera according to the steps
above. However, the camera will not find the network if Wi-Fi router turns
off the SSID broadcasting function. Please enable the SSID broadcasting to
complete the settings.
Note: Most Wi-Fi routers broadcast the Service Set Identifier (SSID) by default. This
is the name of your wireless network, and SSID broadcasting is how Wi-Fi-enabled
devices find networks.
The camera will only accept SSID composed with English alphabet charactors and
arebic numbers, none-English and special charactors (!@#$%, ect.) will not be
accepted.

11
LIVE VIEW / SNAPSHOT / RECORDING
Tap to take snapshot image(s) of the
video. The captured snapshots will be
stored in your mobile device.
Tap to turn ON/OFF the volume.
Tap to Start/Stop recording.
The recorded video file will be stored
in the memory card of your camera.
Tap to return to the main page.
The APP allows users to have access to live video. User can take snapshot
image(s) and record the live video.
When you launch the App on the smart phone or tablet, the image
displaying on the main screen is the very last automatically captured
snapshot from the live view of the previous established session. Tap the
image to enter live view mode.
The controls and layout of the APP have been customized to meet the
operating system requirements of the mobile device. The main page may
vary, depending on your mobile device. By default, the live view is
displayed in portrait mode. You can also turn the device sideways to switch
to landscape mode for a larger view.
Note: Once the recording is started by motion detection or manually, the APP will
continue the recording for 1 minute. User cannot stop the recording during this period.

12
VIEWING YOUR SNAPSHOTS
For iOS
You snapshots will be named with the time stamp and saved into the
Camera Roll location of your mobile device.
For Android
You snapshots will be named with the time stamp and saved into the
Photo Gallery > snapshot folder on your mobile device.
PLAYBACK YOUR VIDEOS
The recorded video file(s) on your camera is automatically saved to the
memory card inserted in your camera. You can remotely access the file(s)
for playback via your mobile device.
Tap the CAMERA SETTING icon on the main page.
(iOS) (Android)

13
Tap EVENT LIST icon and the Date-Time filter would appear.
User may define the period for system to display all available
recorded file(s) for playback.
During the playback, you can tap the PAUSE icon to pause /
resume the video, MUTE to deactivate/activate the audio
function and GO BACK icon to return to the event list section.
You may also review recorded video file(s) with your PC. For
best performance, please use “Free Video Converter” from
http://www.freemake.com/free_video_converter/, or Video LAN
from http://www.videolan.org/.
The video is using FFmpeg codes and is H.264 compression
method.
User’s local network environment condition (example:
upload/download speed) may cause improper video playback
(black screen), when it happens, please leave the playback mode
and try again at later time.
APP layout may vary depending on the display panel size of
your mobile devices. Please refer to the release note from the
APP Store/Google Play for more details.

To Download/Delete the video file(s) in the EVENT LIST
section, please follow the steps below:
．DOWNLOAD
Long press the video clip to download the file onto your
movbile device.
Note: During the download process, system will stop both
the live view and recording functions. APP will
automatically inform any user accessing the camera that the
systemis busy and the connection has been terminated.
14

15
This function helps user to easily withdraw the recorded file(s) from the
memory card. It is strongly suggested to download the file(s) at your
home Wi-Fi network (WLAN), meaning the mobile device(s) is
connecting to the same Wi-Fi router as the camera. Minimum bandwidth
requirment is 1Mbps (upload/download). Download process may be force
stopped if the bandwidth becomes too slow and cannot continue.
Note: For Android system, please use "MX Player" APP for playback
downloaded video file(s). You can find "MX Player" from Google Play
(free of charge).
Note: If you are experiencing scattering video image, please switch the
decoder function of the MX Player to "S/W Decoder".
．DELETE
First select the file(s) by tapping the file name, following by
taping on the Trashcan icon to delete selected file(s) Multiple
files can be selected for delete.
Check the video clip
Then tap the trash can icon

16
MAIN PAGE OVERVIEW
The MAIN PAGE section offers user an overview for all registered
camera(s), including camera status (connected/disconnected). User can
quickly access the camera(s) in the list. When multiple cameras are
registered, scroll down to locate the registered camera for access.
(iOS) (Android)
ADD CAMERA
The ADD CAMERA icon allows you to register additional
camera(s) to the system. The system supports up to 3 concurrent
user connections.
1. Connect the additional camera to the Wi-Fi router using the provided
Ethernet cable. The Wi-Fi router must be the same as what your mobile
device is connecting with.
2. Tap the ADD CAMERA icon. The System Information panel appears.
Specify a name or use the default system name for your camera in the
SYSTEM NAME field.
3. Enter the DID code that provided with your camera in the DID column.

17
4. Enter the default password 123456 in
the Security Code column.
5. Click SAVE to complete the camera settings. The APP attempts to
establish camera connection. Once the camera is successfully connected,
the “Connected” status will be shown on the left upper corner.
6. Repeat step 2 to 5 to add more cameras.

18
In the CAMERA SETTING section you will allow to (1)
configure system setting, (2) unregister camera from the APP
and (3) enter event list for recorded video file(s) playback. Tap
the CAMERA SETTING icon to enter/exit CAMERA
SETTING.
Tap the CAMERA SETTING icon. The following icons appear on the
panel.
(iOS) (Android)
Tap the ADVANCED SETTING icon to setup camera
configuration. (Please refer to "Advanced Setting" for detail).
Tap the DELETE icon to remove the camera connection.
Tap the EVENT LIST icon to check or playback the recorded
events. (Please refer to "Playback Your Video" for detail).
The INFORMATION icon allows you to enable PIN lock, push
notification function and check the App information.