Emerson IC695CPE330 User manual

QUICK START GUIDE
GFK-2941K
Sep 2019
PACSystemsTM RX3i
1GHZ 64MB CPU WITH ETHERNET
(IC695CPE330)

Quick Start Guide Contents
GFK-2941K Sep 2019
Contents i
Contents
1. User Features ..................................................................................1
1.1. Switches ...................................................................................... 4
1.2. Light-Emitting Diode Indicators (LEDs).........................................6
1.3. Ethernet Ports.............................................................................. 8
2. Hardware Installation......................................................................11
2.1. Initial Checks..............................................................................11
2.2. Installation Location...................................................................11
2.3. Installation in Hazardous Areas ..................................................12
2.4. Grounding .................................................................................12
3. Module Start-up .............................................................................14
3.1. You Will Need: ........................................................................... 14
3.2. Basic Installation Steps:..............................................................14
3.3. Redundancy Configuration ........................................................15
3.4. PROFINET Controller Configuration............................................16
3.5. Backward Compatibility with CPU320/CRU320/CPU315 ............16
3.6. Removable Data Storage Device (RDSD) ....................................18
4. Periodic Maintenance......................................................................19
4.1. Real-Time Clock Battery .............................................................19
4.2. Spare Parts.................................................................................19
5. Additional Information....................................................................20

GFK-2941K Sep 2019
ii
Warning Notes as Used in this Publication
Warning
Warning notices are used in this publication to
emphasize that hazardous voltages, currents,
temperatures, or other conditions that could cause
personal injury to exist in this equipment or may be
associated with its use.
In situations where inattention could cause either
personal injury or damage to equipment, a Warning
notice is used.
Notes: Notes merely call attention to information that is especially significant to understanding and
operating the equipment.
These instructions do not purport to cover all details or variations in equipment, nor to provide
for every possible contingency to be met during installation, operation, and maintenance. The
information is supplied for informational purposes only, and Emerson makes no warranty as to
the accuracy of the information included herein. Changes, modifications, and/or improvements
to equipment and specifications are made periodically and these changes may or may not be
reflected herein. It is understood that Emerson may make changes, modifications, or
improvements to the equipment referenced herein or to the document itself at any time. This
document is intended for trained personnel familiar with the Emerson products referenced
herein.
Emerson may have patents or pending patent applications covering subject matter in this
document. The furnishing of this document does not provide any license whatsoever to any of
these patents.
Emerson provides the following document and the information included therein as-is and
without warranty of any kind, expressed or implied, including but not limited to any implied
statutory warranty of merchantability or fitness for particular purpose.

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 1
1. User Features
The PACSystems RX3i CPE330 is a richly
featured programmable controller CPU
equipped with a 1GHz dual-core
microprocessor, 64Mbytes of built-in
program memory and two independent
high-speed Ethernet interfaces. It is ideally
suited for multi-tier communications and for
synchronizing large amounts of data. Its
metal housing provides superior noise
immunity.
Figure 1: IC695CPE330 Features at a
Glance
The CPE330 is programmed and configured
over Ethernet via Emerson’s PAC Machine
Edition (PME) software. It resides in the RX3i
main rack and supports all RX3i I/O and
Intelligent Option modules, up to 32K I/O
points.
•RX3i Hot Standby Redundancy CPU with
support for PROFINET I/O using
embedded PROFINET or using rack-
mounted IC695PNC001 PROFINET
Controllers.
•RX3i Hot Standby Redundancy with
Ethernet (EGD) & Genius I/O.
•Simplex PROFINET I/O Controller with

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 2
support for up to 32 I/O devices and update rates of 1 –512ms. I/O device update
rates of 8ms and faster are possible with 16 or fewer devices. When there are
more than 16 devices configured, update rates of 16ms and higher are available.
•Supports two independents 10/100/1000 Ethernet LANs. As shown in Figure-1,
LAN1 attaches via the upper, dedicated RJ-45 connector. LAN2 attaches via the
lower pair of internally-switched RJ-45 connectors.
•The embedded Ethernet interface is supported by a dedicated microprocessor
core. This dedicated processing capability permits the CPU to support these two
LANs with:
oup to 48 simultaneous SRTP Server connections;
oup to 16 simultaneous Modbus/TCP Server connections;
o32 Clients are permitted; each may be SRTP or Modbus/TCP.
oOPC UA Server with support for up to 5 concurrent sessions with up to
10 concurrent variable subscriptions and up to 12,500 variables;
oup to 255 simultaneous Class 1 Ethernet Global Data (EGD)
exchanges;
otwo independent Redundant IP addresses, one for each of the
embedded Ethernet LANs.

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 3
•Achilles Level 2 Communications Certification1.
•Supports secure firmware update. The controller authenticates new firmware
prior to installation and continues to use the current version if non-authentic
firmware is detected.
•Embedded SNTP Client allows synchronization of the high-resolution Time of Day
Clock to an SNTP network time server.
•Optional Energy Pack, IC695ACC402, allows CPE330 to instantly save user
memory to non-volatile storage in the event of loss of power.
•Ability to transfer user programs and/or data to and from USB 2.0 A type
Removable Data Storage Devices (RDSDs).
•HART Pass Through allows the CPE330 to communicate HART asset management
data between HART-capable I/O modules and PC-based asset management tools.
(Requires additional HART-compatible products.)
•Supports the Remote Get HART Device Information COMMREQ, which allows the
user application to read information from a HART device connected to an RX3i
Analog module in an IC695PNS001 RX3i PROFINET Scanner. A UDFB that
automates the COMMREQ control logic is available for download from the Emerson
support website. (Refer to New Features and Enhancements for additional
information.)
•Sequence of Events recording is available through the Embedded PROFINET
Controller when used with up to four IC695PNS101 Advanced PROFINET Scanner
modules. A RX3i SoE system supports events from up to 512 SoE input points with
a system storage buffer for up to 128,000 events at a maximum rate of 400 events
per second per PNS101. Each PNS101 supports SoE recording with IRIG B time
synchronization of events accurate to 1ms and buffers up to 4000 events from up
to four IC694MDL660 32 Circuit Discrete Input modules. Unmodulated IRIG B time
1
Achilles Level 2 Communications Certification available in CPE330 R8.80

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 4
signals are decoded by the PNS101 using either an IC695HSC304 or IC695HSC308
High Speed Counter Module. SoE recording is available in both simplex and
redundant PROFINET systems.
•User may program in Ladder Diagram, Structured Text, Function Block Diagram, or
C.
•Contains 64Mbytes of configurable data and program memory.
•Supports auto-located Symbolic Variables that can use any amount of user
memory.
•Reference tables include 32k bits for discrete %I and %Q and up to 32k words each
for analog %AI and %AQ. Bulk memory (%W) also supported for data exchanges.
•Supports up to 768 program blocks. Maximum size for a block is 128KB.
•For supported I/O, Communications, Motion, and Intelligent modules, refer to the
PACSystems RX3i System Manual, GFK-2314.
•Ability to display serial number and date code in PME Device Information Details.
•Coordinated Universal Time (UTC) and Day Light Savings Time (DST) support.
•Operating temperature range 0C to 60C (32 F to 140 F).
1.1. Switches
The Run/Stop switch and RDSD UPLD and RDSD DNLD pushbuttons are located
behind the protective front door. Switch operation is given in the following table.
RDSD
Pushbuttons
Function
RDSD UPLD
Loads user program or data from CPU to RDSD.
RDSD DNLD
Stores user program or data from RDSD to CPU.
Run/Stop
Switch Position
A three-position switch which operates as follows:
CPU and Sweep Mode
Memory Protection

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 5
Run I/O
The CPU runs with I/O
sweep enabled.
User program memory is
read only.
Run
The CPU runs with
outputs disabled.
User program memory is
read only.
Stop
The CPU is not allowed to
go into Run mode.
User program memory can
be written.
The Run/Stop switch is enabled by default; it can be disabled in the PME Hardware
Configuration (HWC) settings. The memory protection function of this switch can be
disabled separately in HWC. The memory protection functionality is disabled by
default.

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 6
1.2. Light-Emitting Diode Indicators (LEDs)
Status Indicators
LED
LED State
Operating State
CPU OK
On Green
CPU has passed its power-up diagnostics and is
functioning properly. (After initialization sequence
is complete.)
Off
Power is not applied, or CPU has a problem,
which may be indicated by blink pattern.
Blinking
Other
LEDs off
CPU in Stop-Halt state; possible watchdog timer
fault. If the programmer cannot connect, cycle
power with charged Energy Pack attached and
refer to fault tables.
CPU OK
On Amber
CPU indicating CPU320/CRU320 compatibility
setting
FORCE
On Amber
Refer to the section, Backward Compatibility with
CPU320/CRU320/CPU315 for more information.
RUN
Blinking in
unison
CPU is updating an internal programmable
hardware device.
OUT EN
RUN
On Green
CPU is in Run mode.
Off
CPU is in Stop mode.
OUT EN
On Green
Output scan is enabled.
Off
Output scan is disabled.
FORCE
On Amber
Override is active on a bit reference.

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 7
LED
LED State
Operating State
Off
No Overrides active in I/O Reference Tables.
RDSD
On Green
USB Device detected (No Activity)
Blinking
Green
Port activity detected on USB Interface
Off
No port activity detected on USB Interface
On Red
RDSD Failure
Blinking
Red
Target name mismatch: Press same RDSD
pushbutton again to dismiss.
SYS FLT
On Red
CPU is in Stop/Faulted mode: a fatal fault has
occurred.
Off
No fatal faults detected.
CPE330 Ethernet Indicators
LED
LED State
Operating State
LINK
(upper)
On Green
The corresponding link is physically
connected.
Blinking
Green
Traffic is detected at the corresponding
port.
Off
No connection detected at corresponding
port.
1Gbps
(lower)
On Amber
(LAN1) or
Corresponding network data speed is 1
Gbps.
On Green
(LAN2)

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 8
LED
LED State
Operating State
Off
Corresponding network data speed is 100
Mbps or 10 Mbps.
1.3. Ethernet Ports
LAN1 connects to the uppermost RJ-45 connector. It is not switched. LAN2 connects
to the two lower RJ-45 connectors. They are switched internally. Record the IP
Address of each LAN in the space provided (Figure-1).
Each of the embedded Ethernet interfaces automatically senses the data rate
(10 Mbps or 100 Mbps or 1 Gbps), communications mode (half-duplex or full-
duplex), and cabling arrangement (straight-through or crossover) of the attached
link.
For improved performance, the two Ethernet LANs are serviced by a dedicated
microprocessor core. In addition, each Ethernet LAN is serviced by a dedicated
Network Interface Controller (NIC). In this way, the servicing of the Ethernet ports is
independent of the controller logic and I/O scanning. This superior level of servicing
is required at the higher communications rates.
Any of the embedded Ethernet ports may be used to communicate with the PME
programming software using the Service Request Transport Protocol (SRTP, a
proprietary GE protocol, used primarily for communication with the programmer).
To establish Ethernet communications between the PME programming and
configuration software and the CPU, you first need to set an IP address. Use the
Set IP Address tool (refer to PACSystems RX7i, RX3i, & RSTi-EP CPU Reference Manual,
GFK-2222V) or use the factory-shipped default settings:
CPE330 LAN1
CPE330 LAN2

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 9
IP Address:
192.168.0.100
10.10.0.100
Subnet
Mask:
255.255.255.0
255.255.255.0
Gateway:
0.0.0.0
0.0.0.0
Figure 2: Typical Multi-tier LAN Application
A typical application will take advantage of the two independent LANs. The dedicated
LAN1 port will be used for communications with plant-level or supervisory layers. The

Quick Start Guide Section 1
GFK-2941K Sep 2019
User Features 10
switched LAN2 will typically be used to communicate with devices within the
manufacturing cell or process, including local HMI devices and micro-controllers.

Quick Start Guide Section 2
GFK-2941K Sep 2019
Hardware Installation 11
2. Hardware Installation
2.1. Initial Checks
Upon receiving your RX3i equipment, carefully inspect all shipping containers for
damage. If any part of the system is damaged, notify the carrier immediately. The
damaged shipping container should be saved as evidence for inspection by the
carrier.
As the consignee, it is your responsibility to register a claim with the carrier for
damage incurred during shipment. Emerson will fully cooperate with you, however,
should such action be necessary.
After unpacking the RX3i equipment, record all serial numbers. Serial numbers are
required if you should need to contact Customer Care during the warranty period. All
shipping containers and all packing material should be saved should it be necessary
to transport or ship any part of the system.
Verify that all components of the system have been received and that they agree with
your order. If the system received does not agree with your order, contact Customer
Care.
2.2. Installation Location
This product is intended for use with the RX3i system. Its components are considered
open equipment (having live electrical parts that may be accessible to users) and
must be installed in an ultimate enclosure that is manufactured to provide safety. At
a minimum, the enclosure shall provide a degree of protection against solid objects
as small as 12mm (e.g. fingers). This equates to a NEMA/UL Type 1 enclosure or an
IEC60529 IP20 rating providing at least a pollution degree 2 environment. For details
about installing RX3i rack systems, refer to the PACSystems RX3i System Manual,
GFK-2314.

Quick Start Guide Section 2
GFK-2941K Sep 2019
Hardware Installation 12
If you need technical help, contact Technical Support. For phone numbers and email
addresses, refer to the back cover of this Guide.
2.3. Installation in Hazardous Areas
The following information is for products bearing the UL marking for Hazardous Areas
or ATEX marking for explosive atmospheres:
CLASS 1 DIVISION 2 GROUPS ABCD
•This equipment is an open-type device and is meant to be installed in an
enclosure suitable for the environment that is only accessible with the use
of a tool.
•Suitable for use in Class I, Division 2, Groups A, B, C and D Hazardous
Locations, or nonhazardous locations only.
WARNING
•EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR
SUITABILITY FOR CLASS I, DIVISION 2.
•EXPLOSION HAZARD - WHEN IN HAZARDOUS AREAS, TURN OFF POWER
BEFORE REPLACING OR WIRING MODULES.
ATEX Zone 2
This module must be mounted in an enclosure certified in accordance with EN60079-
15 for use in Zone 2, Group IIC and rated IP54. The enclosure shall only be able to be
opened with the use of a tool.
2.4. Grounding
The RX3i rack into which this product will be mounted must be grounded per the
instructions provided in PACSystems RX3i System Manual, GFK-2314. Also, if an

Quick Start Guide Section 2
GFK-2941K Sep 2019
Hardware Installation 13
Energy Pack (IC695ACC402) is connected, its ground-strap must be grounded as
described in PACSystems RX3i Energy Pack IC695ACC402 Quick Start Guide,
GFK-2939.

Quick Start Guide Section 3
GFK-2941K Sep 2019
Module Start-up 14
3. Module Start-up
3.1. You Will Need:
•An RX3i Universal Backplane: IC695CHS007, IC695CHS012 or IC695CHS016.
•This PACSystems RX3i CPU. This CPU occupies two backplane slots.
•An RX3i rack-mounted Power Supply Module and compatible power source
(AC
2
or DC).
•A computer running PAC Machine Edition (PME) configuration and
programming software. PME Version 8.60 SIM 8 or later supports all features
in this document.
•Ethernet cable for connecting the PME programmer computer to the RX3i CPU.
•Phillip’s head screwdriver.
•Very small slotted screwdriver (1.4mm jeweler’s size).
3.2. Basic Installation Steps:
For startup and configuration of the CPE330, complete the following steps. For full
details on CPE330 operation, refer to the PACSystems RX7i, RX3i & RSTi-EP CPU
Reference Manual, GFK-2222V or later.
1. Turn power off at the RX3i rack and install the CPE330 in a double-slot which is
CPU-compatible (refer to PACSystems RX3i System Manual, GFK-2314 Chapter
3). Typically, the CPU is in the left-most slot pair, or in the pair of slots to the right
of the power supply module.
2
Note: on lightly-loaded racks, use IC695PSA040H or later, or IC695PSA140D or later, otherwise
power-up may be unsuccessful. Alternately, fill out the empty slots in the rack to draw more
current.

Quick Start Guide Section 3
GFK-2941K Sep 2019
Hardware Installation 15
2. If used, mount the compatible RX3i Energy Pack (IC695ACC402) within 3 feet of
the CPU. The dedicated interconnect cable attaches to the underside of CPE330.
Follow interconnect and grounding instructions in PACSystems RX3i Energy Pack
IC695ACC402 Quick Start Guide, GFK-2939. Secure the two-retention flat-head
screws with a very small slotted screwdriver.
3. Set the pair of hook tabs at top rear of the CPU module into two adjacent notches
on the alignment rail of the RX3i rack backplane. This aligns the module with the
intended slots in the main rack and with the right-side connector of this pair.
4. Swing the module down until the rear connector on the CPU module engages the
mating backplane connector. Firmly engage the connectors.
5. Visually inspect the module to be sure it is properly seated.
6. Using a Phillip’s head screwdriver, secure the two captive M3x5 machine screws
into the matching threaded holes in the backplate of the RX3i I/O rack. The two
screws are located at the bottom rear of the CPU module. Tighten.
7. Apply power to the rack.
Note: When the ACC402 Energy Pack is powered up, a period of time is required to charge it up to
its operating level. During this time, the Energy Pack will indicate this condition via its LEDs
(refer to PACSystems RX3i Energy Pack IC695ACC402 Quick Start Guide, GFK-2939).
The CPE330 will begin its boot cycle once ACC402 is charged. This typically takes 90 seconds
or less. In the event the ACC402 is faulty or is not communicating, CPE330 commences
operation without the Energy Pack.
3.3. Redundancy Configuration
PROFICY Machine Edition 8.60 SIM 8 or later may be used to create native CPE330
redundant applications when a rack-mounted IC695PNC001 is used as the
PROFINET Controller. If using the CPE330 Embedded PROFINET Controller, use PME
9.50 SIM 7 or later.

Quick Start Guide Section 3
GFK-2941K Sep 2019
Hardware Installation 16
To enable redundancy in a CPE330 project, select the CPE330 target in the PME
Navigator and use the Property Inspector to change the Enable Redundancy target
property to True.
3.4. PROFINET Controller Configuration
PROFICY Machine Edition 8.60 SIM 13, PME 9.00 SIM 4 or later may be used to
configure an Embedded PROFINET Controller in the CPE330 Hardware Configuration
on LAN 2.
To enable the PROFINET Controller in a CPE330 project, select the CPE330
3
target in
the PME Navigator and open the Hardware Configuration. On the Settings tab,
change the LAN 2 Mode to PROFINET. The PROFINET Controller node description now
displays that it is using LAN 2 as a submodule under the CPE330.
3.5. Backward Compatibility with
CPU320/CRU320/CPU315
The CPE330 also serves as a drop-in replacement for the CPU320, CRU320, and
CPU315 Controllers without the need to upgrade PME. To download projects
intended for the CPU320/CRU320 to a CPE330 with versions of PME that do not
support the CPE330, you must change the CPE330’s compatibility setting.
To change the compatibility setting, perform the following operations:
1. Power off the CPE330 and remove any USB stick that might be attached to
its USB connector.
2. Place the CPE330’s RUN/STOP switch in the STOP position.
3
CPE330 release 8.90 or later is required for the embedded PNC feature.

Quick Start Guide Section 3
GFK-2941K Sep 2019
Hardware Installation 17
3. Hold down the RDSD UPLD button and turn power on to the CPE330.
Continue to depress the RDSD UPLD button until the CPE330 powers up and
displays one of the following patterns on the LEDs.
CPU Status Indicators
On
Blinking
Off
CPE330 LED
LED State
Operating State
CPU OK
On Amber
Normal mode. (Compatible
with CPU320)
FORCE
On Amber
RUN
Off
RDSD
On Red
OUT EN
Off
SYS FLT
On Red
CPU OK
On Amber
CRU320 Compatibility mode.
FORCE
On Amber
RUN
On Red
RDSD
Off
OUT EN
Off
SYS FLT
On Red
4. To toggle the compatibility setting, press the RDSD DNLD button. The
compatibility indication will toggle between the Normal (CPU320) and
CRU320 compatibility patterns each time the RDSD DNLD button is
pressed.
5. When the desired compatibility setting is displayed, press the RDSD UPLD
button to save the setting and allow the CPE330 to continue its normal