Emerson PACSystems RX3i IC695CPE302-B Series User manual

PACSystems™ RX3i Central Processing
Unit IC695CPE302-Bxxx/IC695CPE305-
Bxxx/IC695CPE310-Bxxx
Quick Start Guide
GFK-3249B
Sep 2022

i PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Contents
Contents .................................................................................................i
Front Panel Description ...........................................................................1
CPE302-Bxxx/CPE305-Bxxx ............................................................................. 1
CPE310-Bxxx .................................................................................................. 2
Switches.................................................................................................3
Switch Operation ....................................................................................3
Real-Time Clock Battery...........................................................................4
Ethernet Ports.........................................................................................4
Serial Port ...............................................................................................5
Removable Data Storage Devices (RDSDs)................................................5
Energy Pack ............................................................................................6
Light-Emitting Diode Indicators (LEDs) .....................................................6
Hardware Installation ..............................................................................8
Initial Checks.................................................................................................. 8
Installation Guidelines .................................................................................... 8
Module Installation .................................................................................9
Module Initial Startup............................................................................11
Initial Configuration...................................................................................... 11
General Contact Information ........................................................................ 15

1 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Front Panel Description
CPE302-Bxxx/CPE305-Bxxx

2 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
CPE310-Bxxx

3 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Switches
The RDSD and Run Mode switches are located behind the front protective
door. The Reset switch is not used. Switch operation is given in the following
table.
Switch Operation
RDSD Switches
Function
Start Pushbutton
Pressing this switch initiates RDSD data transfer. (The
three-position switch must be set to Upload or Download.)
RDSD Switch
The RDSD Switch enables and disables RDSD data transfer
and selects the direction of data transfer.
Upload
Loads application from CPU
to RDSD.
Off
Disables RDSD data
transfer.
Download
Stores application from
RDSD to CPU.
PHY PRES Pushbutton
Used to reset the password on the firmware upgrade
webpage.
Run Mode Switch
Run I/O Enable
The CPU runs with I/O
sweep enabled.
Run Output Disable
The CPU runs with
outputs disabled.
Stop
The CPU is not allowed to
go into Run mode.
The Run Mode switch can be disabled in the programming software in Hardware
Configuration (HWC). The switch’s memory protection function can be disabled
separately in HWC. The Run Mode switch is enabled by default. The memory
protection functionality is disabled by default.

4 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Real-Time Clock Battery
The CPE302/305/310-Bxxx is shipped with a real-time clock (RTC) battery
(IC690ACC001) installed.
There are no diagnostics or indicators to monitor RTC battery status. The RTC
battery has an estimated life of 5 years and must be replaced every 5 years
on a regular maintenance schedule. If the RTC battery fails, the CPU date and
time are reset to 12:00 AM, 01-10-2000 at startup. The CPU operates
normally with a failed or missing RTC battery; only the initial CPU Time-of-
day (TOD) clock information will be incorrect.
For instructions on replacing the Real-Time Clock Battery, please refer to the
PACSystemsTM RX3i and RSTi-EP CPU Reference Manual (GFK-2222).
Ethernet Ports
The embedded Ethernet interface supports communications with PAC
Machine Edition programming software using the proprietary SRTP protocol.
The CPE302/305/310-Bxxx CPU provides two SRTP server connections.
The embedded Ethernet interface has two RJ-45 Ethernet ports that are
switched internally and can automatically sense the data rate (10 Mbps or
100 Mbps or 1000 Mbps), duplex status (half or full duplex), and cabling
arrangement (straight-through or crossover) of the attached link.

5 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Serial Port
The CPE302/305-Bxxx provides one RS-232 serial interface to external
devices. The CPE310-Bxxx provides two COM Ports, COM1 an RS-232 serial
interface with a standard D-sub 9-pin female connector, and COM2 an RS-
485 serial interface with D-sub 15-pin female connector. The serial ports of
CPE302/305/310-Bxxx are electrically isolated. For serial port pin
assignments and details on serial communications, refer to the PACSystems
RX3i and RSTi-EP CPU Reference Manual, GFK-2222.
The RS-232 port does not supply the 5 VDC power offered by other RX3i and
Series 90-30 CPUs. Cable IC693CBL316 must be used for RS-232 serial
connections to the CPE302/305-Bxxx.
Removable Data Storage Devices
(RDSDs)
The CPE302/305/310-Bxxx provides the ability to transfer applications to and
from an RDSD (USB-compatible device, such as a memory stick, smartphone,
digital camera, or MP3 device). Once the data is copied to the RDSD, it can
be written to other RX3i CPE302/305/310-Bxxx CPUs with no programmer
software needed. The RDSD interface requires a user-supplied flash memory
device that complies with the USB 2.0 Specification.
The USB port must be enabled in the RX3i configuration to transfer data
between the CPU and the RDSD. The CPE302/305/310-Bxxx is shipped with
the RDSD (USB) port enabled. Complete details of the use of RDSDs are found
in the PACSystems RX3i and RSTi-EP CPU Reference Manual, GFK-2222.

6 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Energy Pack
The CPE302/305/310-Bxxx preserves user memory using an Energy Pack
without the need to periodically replace batteries. The IC695ACC400 Energy
Pack powers the CPU long enough for the CPU to write its user memory
contents to the CPU’s non-volatile storage during a system power loss.
Installation of the Energy Pack is found in the Module Installation section.
Light-Emitting Diode Indicators (LEDs)
LED
LED State
Operating State
OK
Green,
ON steady
CPU passed power-up diagnostics, functioning
properly
OFF
Power is not applied, or the CPU has a problem,
which may be indicated by RN and EN blink pattern
Green, blinking
CPU in Stop-Halt state; possible watchdog timer
fault. Refer to the fault tables. If the programmer
cannot connect, cycle power with a charged Energy
Pack attached and refer to fault tables
RN
Green,
ON steady
CPU passed power-up diagnostics, functioning
properly
OFF
Power is not applied, or the CPU has a problem,
which may be indicated by RN and EN blink pattern
Green, blinking
CPU in Stop-Halt state; possible watchdog timer
fault. Refer to the fault tables. If the programmer
cannot connect, cycle power with a charged Energy
Pack attached and refer to fault tables

7 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
LED
LED State
Operating State
EN
Green,
ON steady
Output scan is enabled.
OFF
Output scan is disabled.
RN/EN
Green, blinking
CPU is in firmware update mode, it enters this mode
when initiated through a web browser. In this
mode, the CPU is updating its firmware and the
images of other internal programmable devices.
CM
Green, blinking
Signal activity on the COM1 port.
OFF
No activity on the COM1 port.
FRCE
Amber,
ON steady
Override active on at least one-bit reference.
OFF
No overrides applied.
STAT
OFF
Energy Pack is not connected.
Green, blinking
Energy Pack charging; not yet charged above the
minimum operating voltage.
Green, ON
Steady
Energy Pack is charged above its minimum
operating voltage.
Red, ON
Energy Pack circuit fault.
Red, blinking
Energy Pack is near its end of life and should be
replaced soon.
FLT
OFF
No fatal faults.
Red, ON
CPU is in Stop/Faulted mode because a fatal fault
has occurred.
RDSD
Green, blinking
Indicates signal activity on USB-A/RDSD/COM2 Port.
OFF
No activity on USB-A/RDSD/COM2 Port.

8 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Hardware Installation
Initial Checks
Upon receiving your RX3i equipment, carefully inspect all shipping
containers for damage. If any part of the system is damaged, notify the
carrier immediately. The damaged shipping container should be saved as
evidence for inspection by the carrier.
As the consignee, it is your responsibility to register a claim with the carrier
for damage incurred during shipment. Emerson Automation Solutions will
fully cooperate with you, however, should such action be necessary.
After unpacking the RX3i equipment, record all serial numbers. Serial
numbers are required if you need to contact Customer Care during the
warranty period. All shipping containers and all packing material should be
saved should it be necessary to transport or ship any part of the system.
Verify that all components of the system have been received and that they
agree with your order. If the system received does not agree with your order,
contact Customer Care.
Installation Guidelines
For information on installation areas, please consult the RX3i Installation and
Maintenance Requirements documentation (GFK-3069) included with the
product.

9 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Module Installation
For the initial startup and configuration of the CPE302/305/310-Bxxx,
complete the following steps. For full details on CPE302/305/310-Bxxx
operation, refer to the PACSystems RX3i and RSTi-EP CPU Reference Manual,
GFK-2222.
1. Remove power from the RX3i rack and install the CPE302/305/310-Bxxx.
2. The CPE302/305/310-Bxxx
may be installed in any slot in
the RX3i Main rack, except the
highest-numbered slot or
slot 0.
3. Holding the module firmly,
align the module with the
correct slot and connector,
then swing the module down
until the module’s connector
engages the backplane’s
backplane connector.
Figure 1: Module Installation

10 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
4. For CPE302/305-Bxxx:
a. Visually inspect the module to be sure it is properly seated.
b. Tighten the two captive screws located in the module’s
bottom bracket to fasten the bottom to the backplate.
Tighten screws using a #1 Phillips screwdriver. Tighten to
0.7 N-m (6 in-lbs.).
5. For CPE310-Bxxx:
a. Ensure the release lever on the bottom of the module snaps
into place in the bottom module retainer of the backplane.
b. Visually inspect the module to be sure it is properly seated.
6. Mount the Energy Pack on the left side of the module in slot 0 of the rack
(typically a power supply).
a. Engage the Energy Pack’s mounting hooks (at the top) on the frame
of the leftmost module.
b. Rotate the bottom of the Energy Pack into place, engaging the
bottom hooks. The latch will snap into place.
c. Connect cable IC695CBL001 from the connector on the bottom of
the Energy Pack to the corresponding connector on the bottom of
CPE302/305/310-Bxxx.
7. If required, connect the CPE302/305/310-Bxxx to the Ethernet network.
8. Apply power to the rack.
Note: When the Energy Pack is powered up for the first time or is
in a system that has been powered down long enough to
completely discharge the Energy Pack, it may require a few
seconds for it to charge to its operating level. The CPU’s
STATUS LED will blink green during this time.

11 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Module Initial Startup
You Will Need:
•PACSystems RX3i CPU Firmware 10.60 or later.
•PAC Machine Edition™configuration and programming software,
version 8.00 SIM 7 or later.
•An IC693CBL316 serial or Ethernet cable for connecting the
computer running the PAC Machine Edition programmer to the RX3i
CPU.
Initial Configuration
1. Using PAC Machine Edition (PME) software, configure the
CPE302/305/310-Bxxx in an RX3i target.
Note: If you intend to use the module’s embedded Ethernet
interface, you will probably need to assign it a new IP
address. To configure the embedded Ethernet interface in
Machine Edition, expand the CPU slot to display the
Ethernet daughterboard. The Settings tab for the
embedded Ethernet module contains IP Address, Subnet
Mask, and Gateway IP Address (see the following diagram).
Consult your network administrator for the proper values
for these parameters.

12 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Figure 2: Configuration of the Ethernet Port on CPE302/305/310-Bxxx
2. Go online with the target and download the configuration. You can
use one of the following methods for the initial connection to the
CPE302/305/310-Bxxx:
a. Connect to CPE302/305-Bxxx using an IC693CBL316 cable, and
connect to the module’s RJ-25 RS-232 serial port to the
programmer's computer. The computer must be equipped with
a RS-232 serial port with a standard AT-style nine-pin male D-
connector.
b. Connect to CPE310-Bxxx using a standard straight-through cable
to the module’s COM1 port (RS-232) from the serial port of the
programmer's computer. The computer must be equipped with
a RS-232 serial port with a standard AT-style nine-pin male D-
connector.

13 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
c. Connect to the module’s
Ethernet port, using the
factory-loaded IP address,
192.168.0.100.
Note: This address is intended
only for the initial connection to
complete the configuration.
After the initial configuration
download must be changed
before connecting to the
Ethernet network. When you
store a hardware configuration
with a different IP address, the
temporary IP address is lost; it is
not restored by a Clear operation.
d. Through the Ethernet
connection of an ETM001 in the same rack with a known IP
address configuration.
Figure 3: IP Address Visible in
Inspector Pane

14 PACSystems™ RX3i IC695CPE302/305/310-Bxxx GFK-3249B
Additional Information
PACSystems RX3i and RSTi-EP CPU Reference Manual
GFK-2222
PACSystems CPU Programmer’s Reference Manual
GFK-2950
PACSystems RX3i System Manual
GFK-2314
PACSystems RX3i IC695CPE302-Bxxx/IC695CPE305-Bxxx/
IC695CPE310-Bxxx CPU Important Product Information
GFK-3248
PACSystems RX3i and RSTi-EP TCP/IP Ethernet
Communications User Manual
GFK-2224
User manuals, product updates, and other information sources are available
on the Support website.

General Contact Information
Please visit us for product support or updated product information:
Online Technical Support and GlobalCare
http://www.emerson.com/industrial-automation-controls/support
Additional Information
http://www.emerson.com/industrial-automation-controls
All Rights Reserved.
We reserve the right to modify or improve the designs or specifications of the
products mentioned in this manual at any time without notice. Emerson does
not assume responsibility for the selection, use, or maintenance of any product.
Responsibility for the proper selection, use, and maintenance of any Emerson
product remains solely with the purchaser.
©2022 Emerson Electric Co.