Emerson FISHER 670 Series User manual

670 Series
D200109X012
Instruction Manual
Form 965
February 2015
www.fisherregulators.com
670 Series Panel-Mounted Loading
Regulator Assemblies
!
WARNING
Fisher®regulators should be installed,
operated and maintained in accordance
with federal, state and local codes, rules
and regulations and Emerson Process
Management Regulator Technologies,
Inc. instructions.
If a leak develops in the system, it indicates
that service is required. Failure to take the
regulator out of service immediately may
create a hazardous condition.
Call a gas service person in case of trouble.
Only a qualied person must install or
service the regulator.
Introduction
The 670 Series panel-mounted loading regulator assemblies
are used primarily for manually controlling pressure to
diaphragm control valves or as remote pressure loaders for
pressure-balance gas regulators. They are also widely used
for remote control of gas pressure to burners in renery tube
stills, power plants and similar process furnaces.
Principle of Operation
The 670 Series regulators are set manually to control supply
pressure to diaphragm control valves or gas regulators.
Instrument and manual loading pressures are read from the
pressure gauges of the regulator. If pressure to the valve
needs to be adjusted, the regulator handwheel is turned
clockwise to increase the supply pressure or counterclockwise
to decrease the supply pressure.
Installation
Inspect the panel after it is removed from its packing.
Connect a 1/4 in. / 6.4 mm pipe line from the operating
supply pressure to the connection marked “IN” on the
pressure regulator.
One and two-gauge panels: Connect a line to the diaphragm
casing of the main valve or regulator and run it to the
connection marked “OUT” on the panel regulator. When
installing a two-gauge panel, connect a line from the control
pressure line to the upper diaphragm casing and to the
control pressure gauge (instrument loading pressure) in the
back of the panel (see Figure 2).
Two-gauge panel with a three-way changeover valve:
Connect the air supply, diaphragm connection and
instrument loading pressure line to the panel regulator as
shown in Figure 4.
Overpressure Protection
!
WARNING
Overpressuring any portion of this equipment
may cause damage to regulator parts, leaks
in the regulators or personal injury due to
bursting of pressure-containing parts or
explosion of accumulated gas.
To avoid overpressure, provide appropriate
overpressure protection to ensure that none of
the pressure limits will be exceeded.
The regulator assembly should be inspected for
damage after any overpressure condition.
Figure 1. Typical 670 Series Regulators: Two-Gauge Panel with
Three-Way Changeover Valve
W0554

670 Series
2
Table 1. Type Number Description
TYPE NUMBER
OF GAUGE DESCRIPTION REGULATOR TYPE NUMBER
MAXIMUM INLET
PRESSURE
MAXIMUM OUTLET
PRESSURE
MAXIMUM EMERGENCY
OUTLET PRESSURE
psig bar psig bar psig bar
670 1 Basic 1-gauge panel 67CR
250 17.2 100 6.9 110 7.6670F 1 1-gauge panel; regulator has lter 67CFR
670FG 2 2-gauge panel; regulator has lter 67CFR
670FGV 2 2-gauge panel with 3-way changeover valve;
regulator has lter 67CFR 50 3.5 50 3.5 55 3.8
670G 2 Basic 2-gauge panel 67CR 250 17.2 100 6.9 110 7.6
670GV 2 2-gauge panel with 3-way or 4-way changeover valve 67CR 50 3.5 50 3.5 55 3.8
671 1 Basic 1-gauge panel 912N 250 17.2 5 0.35 10 0.69
675 2 Basic 2-gauge panel 67CR 250 17.2 100 6.9 110 7.6
Key Description Part Number
2 Gauge
0 to 5 psig / 0 to 0.35 bar 23A8325X012
0 to 15 psig / 0 to 1.0 bar 2C2332000B2
0 to 30 psig / 0 to 2.1 bar 2C2332000C2
0 to 60 psig / 0 to 4.1 bar 2C2332000D2
0 to 100 psig / 0 to 6.9 bar 2C2332000E2
0 to 160 psig / 0 to 11.0 bar 2C2332X0022
0 to 200 psig / 0 to 13.8 bar 2C2332000F2
0 to 300 psig / 0 to 20.7 bar 2C2332X00A2
0 to 400 psig / 0 to 27.6 bar 2C2332X0032
0 to 600 psig / 0 to 41.3 bar 2C2332X0042
0 to 60 psig / 0 to 4.1 bar and 0 to 4 kg/cm21R766299012
0 to 60 to 200 psig / 0 to 4.1 to 13.8 bar
and 0 to 4 to 14 kg/cm21R766399012
3 Panel
Types 670 and 670F, Zinc 1C233344012
Type 670FG, Steel 3E660725132
Type 670G, Steel 3J846025132
Types 670GV and 670FGV (3-way valve),
Steel 3E660825132
Type 671, Zinc 1C233744012
Type 675G, Steel 3H184325132
4 Clamp bar, Cadmium Plate steel (4 required) 1C233824162
5 Hex Nut, Cadmium Plate Steel
Types 670, 670F, 670FG, 670FGV, 671
and 675G (4 required) 1E985324142
Types 670G and 670GV
(6 required) 1E985324142
6 Machine Screw, Steel (4 required) 1C233928992
7 Tubing, Copper
Type 670 19A1553X012
Type 670F 19A1562X012
Type 670FG 19A1564X012
Type 670FGV 19A1565X012
Type 670G 19A1569X012
Type 670GV 19A1556X012
Type 671 19A1511X012
Type 675G 19A1573X012
8 Fitting, Brass
Types 670, 670F and 671 15A6002X272
All other types 15A6002X262
9 Fitting, Brass
Types 670 and 670F 1C619718992
Type 670FG 15A6002X172
Types 670FGV and 670GV (3 required) 15A6002X172
Type 670G 15A6002X212
Type 671 15A6002XA92
Type 675G (2 required) 1C619718992
As is the case with most regulators, regulators in the
670 Series have outlet pressure ratings which are lower than
the inlet pressure ratings. Overpressure protection is needed if
the actual inlet pressure can exceed the outlet pressure rating.
A common method of overpressure protection is a relief valve.
Maximum emergency outlet pressure ratings are shown in
Table 1 for each loading regulator.
Startup
Open the air supply line. Check all connections for leaks. The
manual loading pressure gauge indicates the loading pressure
on the diaphragm of the main valve. To increase the loading
pressure, turn the handwheel clockwise. To decrease the
loading pressure, turn the handwheel counterclockwise.
Units with a three-way changeover valve may be placed
under manual operation. When changing from manual
to automatic or from automatic to manual control, set the
manual control pressure gauge to read the same as the
instrument pressure in order to prevent bumping.
Maintenance
The regulator can be removed from the panel to be nut
disassembled. Take out the set screws or loosen the hex to
remove the regulators from the panel. Refer to the appropriate
instruction manual for further maintenance on the regulator.
Parts Ordering
When corresponding with your local Sales Ofce about
this equipment, be sure to include the serial number that is
stamped on the nameplate on the back of the panel. Include
the complete eleven-character part numbers from the following
Parts List when ordering new parts.
Parts List
Key Description Part Number
1 Regulator—Part numbers for the regulators
used in the 670 Series are shown in the
regulator instruction manuals

670 Series
3
Figure 2. Typical Installation of a Type 670 Regulator
TYPE 670G LOADING REGULATOR
CONTROL PRESSURE
LOADING PRESSURE
OPERATING MEDIUM
200 FT / 61 m
OR LESS
TYPE 796EK MAIN VALVE
AF5052-C
Figure 4. Type 670GV Regulator Assembly Drawing
DC2668-D
A1728-1
AIR
SUPPLY
CONNECTION TO
MAIN DIAPHRAGM
18 13 19
INSTRUMENT
OUTPUT
Figure 3. Type 671 Regulator Assembly Drawing
19 10 11
15
27
24 25
26
28
2
1
3456789
30A6617

670 Series
©Emerson Process Management Regulator Technologies, Inc., 1987, 2015; All Rights Reserved
The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners. Fisher is a mark owned by Fisher Controls International LLC,
a business of Emerson Process Management.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or
guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specications of such
products at any time without notice.
Emerson Process Management Regulator Technologies, Inc. does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and
maintenance of any Emerson Process Management Regulator Technologies, Inc. product remains solely with the purchaser.
Industrial Regulators
Emerson Process Management
Regulator Technologies, Inc.
USA - Headquarters
McKinney, Texas 75070 USA
Tel: [phone]
Outside U.S. [phone]
Asia-Pacic
Shanghai 201206, China
Tel: [phone]
Europe
Bologna 40013, Italy
Tel: [phone]
Middle East and Africa
Dubai, United Arab Emirates
Tel: [phone]
Natural Gas Technologies
Emerson Process Management
Regulator Technologies, Inc.
USA - Headquarters
McKinney, Texas 75070 USA
Tel: [phone]
Outside U.S. [phone]
Asia-Pacic
Singapore 128461, Singapore
Tel: [phone]
Europe
Bologna 40013, Italy
Tel: [phone]
Chartres 28008, France
Tel: [phone]
Middle East and Africa
Dubai, United Arab Emirates
Tel: [phone]
TESCOM
Emerson Process Management
Tescom Corporation
USA - Headquarters
Elk River, Minnesota 55330-2445, USA
Tels: [phone]
[phone]
Europe
Selmsdorf 23923, Germany
Tel: [phone]
Asia-Pacic
Shanghai 201206, China
Tel: [phone]
For further information visit www.fisherregulators.com
Key Description Part Number
10 Nipple
Types 670, 670F and 670G, Brass 1B678218992
Types 670FGV, 670GV and 675G, Brass
(2 required) 1B678218992
Type 671, Steel 1H392926012
11 Fitting, Brass
Type 670 15A6002X212
Type 670F 15A6002X382
Type 670FG 1L472018992
Types 670FGV, 670G and 670GV
(2 required) 1C619718992
Type 671 1D501621992
Type 675G (2 required) 15A6002X212
12 Tubing, Copper
Type 670GV 19A1560X012
Type 675G 19A1574X012
13 Changeover Valve
Types 670FGV and 670GV 1C269518992
15 Gauge Service Marking(1)
Types 670, 670F and 671 1C538606092
Type 670FG (one of each) 1C538606092
1C538706092
Type 670FGV (one of each) 1L335506092
1L335606092
Types 670G and 670GV (one of each) 1C538606092
14A2561X012
Type 675G (2 required) 1C538606092
16 Machine Screw, Plate steel
Types 670FGV and 670GV (2 required) 1C270328992
Key Description Part Number
17 Fitting, Brass
Type 670G 1C269818992
Types 670GV and 670FGV (2 required) 1C269818992
18 Valve Dial, Plastic
Type 670FGV (3-way valve) 1L351106992
Type 670GV (2-way valve) 1D6367X0021
Type 670GV (3-way valve) 1C269606092
19 Machine Screw, Steel
Types 670, 670F and 671 (2 required) 1C270428992
Types 670FG, 670G and 675G (4 required) 1C270428992
Types 670FGV and 670GV (6 required) 1C270428992
20 Tubing, Copper
Types 670FGV and 670GV (2 required) 19A1558X012
23 Support Post, Brass
Types 670FGV and 670GV (2 required)
(Not shown) 1C269714012
24 Bleed Orice and Screen Assembly, Brass/Monel®
Types 670, 670F, 670FG, 670FGV and 670GV 1K8845X0012
Type 671 1D5015X0012
Type 675G (2 required) 1K8843X0012
25 Serial Plate, Aluminum 1C584011992
26 Hex Nut, Plate steel
Type 670FG (4 required) 1A330328982
All other types (2 required) 1A330328982
27 Fitting
Type 671, Malleable Iron 1D501721992
Types 670FGV and 670GV, Brass 15A6002X212
28 Fitting, Brass
Types 670FGV, 670G and 670GV 15A6002X272
33 Mounting Post, Steel (3 required)
(not shown) 1F2449X0012
1. A plate may be engraved with any service marking or terminology. Letter height is 1/8 in. / 3.2 mm. There is space for 3 lines with up to 16 letters per line.
Monel®is a mark owned by Special Metals Corporation.