Emerson Copeland EVM Series User manual

Copeland™Commercial HVACR
Variable Frequency Drive – EVM Series
Installation Manual

2
Table of Contents
Safety Precautions .................................................................................................................................................. 3
Step 1- Copeland EVM Drive Overview .............................................................................................................. 4
Receiving and Inspection .......................................................................................................................... 4
Rating Label .............................................................................................................................................. 5
Keypad Button Overview ........................................................................................................................... 5
Nomenclature ............................................................................................................................................ 6
Step 2- Copeland EVM Drive Installation ........................................................................................................... 7
Dimensions and Weights .......................................................................................................................... 7
Mounting .................................................................................................................................................... 8
FR1 Mounting Instructions .............................................................................................................................. 9
FR2 Mounting Instructions ............................................................................................................................ 10
FR3 Mounting Instructions ............................................................................................................................ 11
FR4 Mounting Instructions ............................................................................................................................ 12
Mounting and Wiring Option Cards ......................................................................................................... 13-14
Ground Wiring ......................................................................................................................................... 15
Wire Stripping Lengths ............................................................................................................................ 15
Circuit Breakers ....................................................................................................................................... 16
Cable and Fuse Guidelines ..................................................................................................................... 17
UL Guidelines ......................................................................................................................................... 17-18
IEC Guidelines ........................................................................................................................................ 19-20
Panel Mounting ....................................................................................................................................................21
Cable Routing.......................................................................................................................................................22
Wiring the VFD.....................................................................................................................................................22
Checking Cable and Motor Insulation...............................................................................................................22
EMC Installation...................................................................................................................................................22
EMC measures in control panel ........................................................................................................................23
International EMC Protection Req. ..................................................................................................................24
Installation in corner-grounded network...........................................................................................................25
Verifying Rotation .................................................................................................................................... 25
Step 3- Control Board Layout .............................................................................................................................26
I/O Terminal Connections........................................................................................................................ 28
Step 4- Drive Startup and Setup.........................................................................................................................29
Main Menu Navigation ............................................................................................................................. 29
Startup Wizard ............................................................................................................................................... 30
Scan for more information or visit
Climate.Emerson.com/CopelandVariableFrequencyDrives

3
Safety Precautions
ELECTRICAL
SHOCK HAZARD
Disconnect and lock out power before servicing.
Discharge all capacitors before servicing.
Use compressor with grounded system only.
Molded electrical plug must be used when
required.
Refer to original equipment wiring
diagrams.
Electrical
connections must be made by qualified electrical personnel.
Failure to follow these warnings could result in serious personal injury.
WARNING
Before Performing the Installation
• It is strongly recommended to read through
this entire manual for safe and correct
installation.
• Disconnect the power supply of the device.
• Ensure that the devices cannot be accidentally
restarted.
• Verify isolation from the supply.
• Earth and short circuit the device.
• Cover or enclose any adjacent live components.
• Only suitably qualified personnel in accordance
with EN 50110-1/-2 (VDE 0105 Part 100) may
work on this device/system.
• Before installation and before touching the device
ensure that you are free of electrostatic charge.
• The functional earth (FE, PES) must be
connected to the protective earth (PE) or the
potential equalization.
• The system installer is responsible for
implementing this connection.
• Connecting cables and signal lines should be
installed so that inductive or capacitive
interference does not impair the automation
functions.
• Install automation devices and related operating
elements in such a way that they are well protected
against unintentional operation.
• Suitable safety hardware and software measures
should be implemented for the I/O interface so
that an open circuit on the signal side does not
result in undefined states in the automation
devices.
• Ensure a reliable electrical isolation of the extra- low
voltage of the 24 V supply. Only use power supply
units complying with IEC 60364-4-41 (VDE 0100
Part 410) or HD384.4.41 S2.
• Deviations of the input voltage from the rated value
must not exceed the tolerance limits given in the
specifications, otherwise this may cause malfunction
and dangerous operation.
• Emergency stop devices complying with IEC/EN 60204-
1 must be effective in all operating modes of the
automation devices. Unlatching the
emergency-stop devices must not cause a restart.
• Measures should be taken to ensure the proper restart of
programs interrupted after a voltage dip or failure.
• This should not cause dangerous operating
states even for a short time. If necessary,
emergency-stop devices should be
implemented.
• Wherever faults in the automation system may
cause injury or material damage, external measures
must be implemented to ensure a safe operating
state in the event of a fault or malfunction (for
example, by means of separate limit switches,
mechanical interlocks, and so on).
• Depending on their degree of protection,
adjustable frequency drives may contain live
bright metal parts, moving or rotating
components, or hot surfaces during and
immediately after operation.
• Removal of the required covers, improper
installation, or incorrect operation of motor or
adjustable frequency drive may cause the failure
of the device and may lead to serious injury or
damage.
• The electrical installation must be carried out in
accordance with the relevant regulations (for
example, with regard to cable cross sections,
fuses, PE).
• Installations containing adjustable frequency
drives must be provided with additional monitoring
and protective devices in accordance with the
applicable safety regulations. Modifications to the
adjustable frequency drives using the operating
software are permitted.
• All covers and doors must be kept closed during
operation.
• Never touch live parts or cable connections of the
adjustable frequency drive after it has been
disconnected from the power supply. Due to the
charge in the capacitors, these parts may still be live
after disconnection. Fit appropriate warning signs.

4
Step 1 — Copeland EVM Overview
This chapter describes the purpose and contents
of this manual, the receiving inspection
recommendations and the Copeland EVM
Series open drive.
It is recommended to read through the entire
document before attempting to install the
drive.
Use QR code on table of contents page to
reach our EVH AE bulletin for supporting
information that is not included in this
manual.
How to Use this Manual
The purpose of this manual is to provide you with
information necessary to install, start up, and
setup the Emerson Copeland commercial
HVACR variable frequency drive (VFD), EVM
drive. To provide for safe installation and
operation of the equipment, read the safety
guidelines at the beginning of this manual and
follow the procedures outlined in the following
chapters before connecting power to the
Copeland EVM VFD. Keep this operating manual
handy and distribute to all users, technicians and
maintenance personnel for reference.
Receiving and Inspection
The Copeland EVM VFD has met a stringent
series of factory quality requirements before
shipment. It is possible that packaging or
equipment damage may have occurred during
shipment. After receiving your Copeland VFD,
please check for the following:
Check to make sure that the package includes
the install manual, quick start guide, and
accessory packet. The accessory packet
includes:
●
Rubber grommets
●
Control cable grounding clamps
●
Additional grounding screw
Inspect the unit to ensure it was not damaged
during shipment.
Make sure that the part number indicated on the
nameplate corresponds with the catalog number
on your order.
If shipping damage has occurred, please
contact and file a claim with the carrier
involved immediately.
If the delivery does not correspond to your
order, please contact your Emerson electrical
representative.
Note: Do not destroy the packing. The template
printed on the protective cardboard can be used
for marking the mounting points of the Copeland
VFD on the wall or in a cabinet.
Common Abbreviations
Abbreviation Definition
VT Variable torque with low overload rating (110%)
IH
High Overload(150%)
IL
Low Overload(110%)
VFD Variable Frequency Drive

5
Rating Label/Carton Label Keypad Button Overview

6
Nomenclature:
Product Family Basic Sizing Data Critical Features/Options
Output Amps(single phase)
Output Amps(three phase)
100-120V
2D5=2.5A
4D8=4.8A
6D9=6.9A
7D8=7.8A
200-240V
2D5=2.5A
4D8=4.8A
7D8=7.8A
011=11A
017=17A
025=25A
200-240V
2D5=2.5A
4D8=4.8A
7D8=7.8A
011=11A
017=17A
025=25A
032=32A
048=48A
062=62A
380-480V
2D2=2.2A
4D3=4.3A
5D6=5.6A
7D6=7.6A
012=12A
016=16A
023=23A
031=31A
038=38A
046=46A
Platform:
M:Multi-Purpose
Input Voltage
2:200-240V
4:380-480V
5:525-600V
1:100-120V
Onboard Comms
M:Modbus RTU
E:Ethernet/BACnet/Modbus
Option Spot
N:None
Product type
V:Variable
Frequency Drive
Human Interface
N:No screen or keypad
E:Embedded 7 segment
Hardware Protections
F:Internal EMI Filter
N:No EMI Filter, No Choke
Phases Input
1:1Ø
3:3Ø
Electronics
E V
M
-
3 4 4 5 D 6 - E
2
0
E
F
N
Output
Voltage
2:200
-240V 3Ø
4:380
-480V 3Ø
5:525-600V 3Ø
Enclosure
IP Rating
IP20=20

7
Step 2 — Copeland EVM Drive Installation
Dimensions and Weights
Approximate mounting dimensions in inches (mm)
Approximate dimensions in inches (mm)
Frame
size
D H1 H2 W1 W2 W3 Ø
Weight
lb (kg)
FR1
7.09
5.98
5.51
2.83
2.26
2.26
0.20
2.6
(180 (152)
(140) (72) (57.5) (57.5) (5.2)
(1.2)
FR2
7.09
8.66
8.15
4.29
3.56
3.56
0.22
5.7
(180 (220)
(207) (109) (90.5) (90.5) (5.5)
(2.6)
FR3
7.09
10.24
9.72
5.12
4.57
4.57
0.22
8.2
(180 (260)
(247) (130) (116) (116) (5.5)
(3.7)
FR4
7.68
11.81
11.06
7.24
6.3
6.3
0.24
13.9
(195 (300)
(281) (184) (160) (160) (6)
(6.3)

8
Mounting
For mounting space guidelines please follow the below diagram and table. Then find the correct frame size mounting
instructions.
- For EVM Drives utilizing an option card, allow 2.76in. (70mm) for dimension A for the option card
enclosure.
- The below guidelines apply unless testing has been completed to validate a design outside of these
recommendations. This work must be done in collaboration with Emerson Application Engineering.
Table 2. Approximate Space Requirements in inches (mm)
Mounting clearance
Airflow
Input voltage Frame
size
A
in. (mm)
B
in. (mm)
C
in. (mm)
D
in. (mm)
CFM
(m3/h)
100 Vac to 120
Vac, 50/60 Hz 1
phase
FR1
0
0
1.97 (50)
1.97 (50)
14.83 (25.2)
FR2
0 0 1.97 (50) 1.97 (50) 24.72 (42)
200 Vac to 240
Vac, 50/60 Hz 1
phase
FR1
0 0 1.97 (50) 1.97 (50) 14.83 (25.2)
FR2
0 0 1.97 (50) 1.97 (50) 37.43 (63.6)
FR3
0 0 1.97 (50) 1.97 (50) 42.37 (72)
200 Vac to 240
Vac, 50/60 Hz 3
phase
FR1
0 0 1.97 (50) 1.97 (50) 14.83 (25.2)
FR2
0 0 1.97 (50) 1.97 (50) 24.72 (42)
FR3
0 0 1.97 (50) 1.97 (50) 42.37 (72)
FR4
0
0
1.97 (50)
1.97 (50)
75.56 (128.4)
380 Vac to 480
Vac, 50/60 Hz 3
phase
FR1
0
0
1.97 (50)
1.97 (50)
14.83 (25.2)
FR2
0
0
1.97 (50)
1.97 (50)
37.43 (63.6)
FR3
0
0
1.97 (50)
1.97 (50)
58.61 (99.6)
FR4
0 0 1.97 (50) 1.97 (50) 57.56 (97.8)
525 Vac to 600
Vac, 5
0/60 Hz 3
phase
FR2
0
0
1.97 (50)
1.97 (50)
37.43 (63.6)
FR3
0
0
1.97 (50)
1.97 (50)
58.61 (99.6)
FR4
0 0 1.97 (50) 1.97 (50) 57.56 (97.8)
Note: For EVM Drives utilizing an option card, allow 2.76in. (70mm) for dimension A for the option card enclosure

9
FR1 Mounting Instructions
Step 1:
Lift the drive out from the carton and remove the
packaging. The magnetic cores and cable ties are
only included in EMI version drive.
Step 2:
Screw mounting: Attach the drive to the mounting
plate with two M5x20 (or 3/16 in.) screws and two
M5 (or 3/16 in.) nuts. The opening dimension on the
mounting plate should follow required dimensions
(refer to the dimension drawing in Table 1 of this
document).
DIN Rail mounting: Lift the drive at an angle about
30 degrees. Align the top hooks of drive DIN rail
mounting slot with DIN rail top edge. Push down and
rotate the drive to clip the bottom hooks on the bottom
DIN rail edge.
Step 3: (EMI version only)
Input wiring:
• 1P FR1 EMI version: Run the input wires (two line
wires+one grounding wire) through the input
magnetic core before connecting to the input terminal
block (L2/L3) and grounding hole. Tie the input
magnetic core to the input wires with a cable tie.
• 3P 230/480 V FR1 EMI version: Run the input wires
(three line wires + one grounding wire) through the
input magnetic core before connecting to the input
terminal block (L1/L2/L3) and grounding hole. Tie the
input magnetic core to the input wires with a cable tie
Output wiring:
• All1P/3P FR1 EMI version: Run three motor wires
through the output magnetic core before connecting
to the output terminal block. The output grounding
wire should not run through the output magnetic core.
Tie the output magnetic core to the output wires with
a cable tie.
The maximum distance between the input/output
magnetic core’s top surface is 100 mm (3.94 in.). All
EVM non-EMI version drives do not have
input/output magnetic cores.

10
FR2 Mounting Instructions
Step 1:
Lift the drive out from the carton and remove the
packaging. The magnetic cores and cable ties are
only included in EMI version drive.
Step 2:
Screw mounting: Attach the drive to the mounting
plate with four M5X20 (or 3/16 in.) screws and four
M5 (or 3/16 in.) nuts. The opening dimension on the
mounting plate should follow required dimensions
(refer to the dimensions in Table 1).
DIN Rail mounting: Lift the drive at an angle about
30 degrees. Align the top hooks of drive DIN rail
mounting slot with DIN rail top edge. Push down and
rotate the drive to clip the bottom hooks on the bottom
DIN rail edge.
Step 3: (EMI version only)
Input wiring:
• 1P FR2 EMI version: Run the input wires (two line wires
+ one grounding wire) through the input magnetic
core before connecting to the input terminal block
(L2/L3) and grounding hole. Tie the input magnetic core
to the input wires with a cable tie.
• 3P 230/480 V FR2 EMI version: Run the input wires
(three line wires + one grounding wire) through the
input magnetic core before connecting to the input
terminal block (L1/L2/L3) and grounding hole. Tie the
input magnetic core to the input wires with a cable tie.
• 3P 575 V FR2 EMI version: Does not have input
magnetic core. Connect the three line wires to the input
terminal block (L1/L2/L3) directly.
Output wiring:
• All1P/3P FR2 EMI version: Run three motor wires
through the output magnetic core before connecting to
the output terminal block. The output grounding wire
should not run through the output magnetic core. Tie the
output magnetic core to the output wires with a cable tie.
The maximum distance between the input/output
magnetic core’s top surface is 100 mm (3.94 in.). All
EVM non-EMI version drives do not have input/output
magnetic cores.

11
FR3 Mounting Instructions
Step 1:
Lift the drive out from the carton and remove the
packaging. The magnetic cores and cable ties are
only included in EMI version drive.
Step 2:
Screw mounting: Attach the drive to the mounting
plate with four M5X20 (or 3/16 in.) screws and four M5
(or 3/16 in.) nuts. The opening dimension on the
mounting plate should follow required dimension (refer
to the dimension drawing in Table 1 of this document)
DIN Rail mounting: Lift the drive at an angle about
30 degrees. Align the top hooks of drive DIN rail
mounting slot with DIN rail top edge. Push down and
rotate the drive to clip the bottom hooks on the bottom
DIN rail edge
Step 3: (EMI Version Only)
Input wiring:
• 1P FR3 EMI version: Run the input wires (two line
wires+one grounding wire) through the input magnetic
core before connecting to the input terminal block
(L2/L3) and grounding hole. Tie the input magnetic core
to the input wires with a cable tie.
• 3P 230/480 V FR3 EMI version: Run the input wires
(three line wires + one grounding wire) through the
input magnetic core before connecting to the input
terminal block (L1/L2/L3) and grounding hole. Tie the
input magnetic core to the input wires with a cable tie.
• 3P 575 V FR3 EMI version: Run the input wires (three
line wires) through the input magnetic core before
connecting to input terminal block (L1/L2/L3). The input
grounding wire should not run through the input
magnetic core. Tie the input magnetic core to the input
wires with a cable tie.
Output wiring:
• 1P FR3 EMI Version: Does not have an output
magnetic core. Connect three motor wires to the output
terminal block directly.
• 3P 230/480/575 V FR3 EMI Version: Run three
motor wires through the output magnetic core before
connecting to output terminal block. The output
grounding wire should not run through the output
magnetic core. Tie the output magnetic core to the
output wires with a cable tie.
The maximum distance between the input/output
magnetic core’s top surface is 100 mm (3.94 in.). All
EVM non-EMI version drives do not have
input/output magnetic cores.

12
FR4 Mounting Instructions
Step 1:
Lift the drive out from the carton and remove the
packaging. The magnetic cores and cable ties are
only included in EMI version drive.
Step 3: (EMI version only)
Input wiring:
3P 230/480 V FR4 EMI version: Run the input wires (three
line wires + one grounding wire) through the input
magnetic core before connecting to the input terminal block
(L1/L2/L3) and grounding hole. Tie the input magnetic core
to the input wires with a cable tie.
3P 575 V FR4 EMI version: Run the input wires (three line
wires) through the input magnetic core before connecting
to input terminal block (L1/L2/L3). The input grounding wire
should not run through the input magnetic core. Tie the
input magnetic core to the input wires with a cable tie.
Output wiring:
3P 230/480/575 V FR4 EMI Version: Run three motor
wires through the output magnetic core before connecting
to output terminal block. The output grounding wire should
not run through the output magnetic core. Tie the output
magnetic core to the output wires with a cable tie.
The maximum distance between the input/output magnetic
core’s top surface is 100 mm (3.94 in.). All EVM non-EMI
version drives do not have input/ output magnetic cores.
Step 2:
Screw mounting: Attach the drive to the mounting
plate with four M5x20 (or 3/16 in.) screws and four M5
(or 3/16 in.) nuts. The opening dimension on the
mounting plate should follow required dimension
(refer to the dimension drawing in the instruction
leaflet).

13
Step 2:
Remove the option card port label and four snap
covers from the drive.
Step 3:
Connect the cable to option card connector (3) and
MCU board connector (4).
Continue on next page
Mounting Instruction for Option Cards
Step 1:
For enclosed type:
Remove the front cover (1) from the NEMA 1 kit
then remove the terminal cover (2) from the drive.
For open type:
Only remove the terminal cover.

14
Step 4:
Clamp the cable with the optional card port. Mount
the option card to the drive by inserting the four
snaps into the slots on drive.
Option Card Wiring Instruction
Step 5:
For enclosed type:
Install the terminal cover (1) to the drive then install
the front cover (2) to the NEMA 1-kit.
For open type:
Only install the terminal cover to the drive.

15
Ground Wiring
Warning!
Connect only in voltage-free state!
Input power and motor cable stripping lengths
Table 3. Stripping Lengths
Power Wiring in Inches (mm) Motor Wiring in Inches (mm)
Size
A1 B1 C1
D1
A2 B2 C2
D2
FR1
0.39
2.76
0.3
2.76
0.39
2.76
0.39
2.76
(10) (70)
(10) (70)
(10) (70)
(10) (70)
FR2
0.47
2.76
0.4
2.76
0.47
2.76
0.47
2.76
(12) (70)
(12) (70)
(12) (70)
(12) (70)
FR3
0.47
3.54
0.4
3.54
0.47
3.54
0.47
3.54
(12) (90)
(12) (90)
(12) (90)
(12) (90)
FR4
0.79
4.53
0.7
4.53
0.79
4.53
0.79
4.53
(20) (115) (20)
(115) (20)
(115) (20)
(115)

16
Power Connection Tightening Torque
Frame
Size
Power wire
in-lb (Nm)
Ground wire
in-lb (Nm)
FR1
4.4 (0.5)
7.1 (0.8)
1.73 (0.2)
FR2
10.5 (1.2)
7.1 (0.8)
1.73 (0.2)
FR3
10.5 (1.2)
14.2 (1.6)
1.73 (0.2)
FR4
33 (3.73)
14.2 (1.6)
1.73 (0.2)
Notes:
- Strip the motor and power cables as shown above.
- Both UL and IEC tools may be used
- Applies to strained wire, solid wire, or
ferrule installations
Circuit Breaker Sizing
The circuit breaker selected must be in accordance with the National Electric Code (NEC) Requirements. The NEC
determines that circuit breakers should handle 80% of their rated capacity for continuous loads and 100% for
intermittent loads. NEC Articles 210.20, 215.3, and 430 address the NEC requirements in more detail. For safety
reasons it is recommended to assume all loads are continuous.
To explain the process for finding the minimum breaker size necessary, please complete the following:
1. Find your total current load of the circuit (ex: 13.7)
2. Multiply your current load by 1.25 to find your minimum breaker size (ex: 13.7*1.25=17.125)
3. Find the correct breaker to match the size you found in #2. If it is not a standard size, per the NEC, select the next
standard size up. For our example we would select a 20A breaker.
Control wire
in-lb (Nm)

17
Cable and Fuse Guidelines
UL Cable Fuse Sizes
Output rating Input rating UL application
Input
voltage
Frame
size
VT/IL
current
amps
VT/IL
current
amps
Recom
mended
fuse
(Class
J, T, CF
or CC)
(max
rating)
100
kAIC①
Recom-
mended
miniature
inverse-
time
molded-
case
circuit
breaker
(max
rating)
10/14
kAIC①
Recom-
mended
Type E CMC
(max rating)
65 kAIC②
Recom-
mended
inverse-
time
molded-
case
circuit
breaker
(max
rating)
100 kAIC
(open type
only for
3-phase)①
NEC
wire
size
line
and
motor
AWG
NEC
wire
size
ground
AWG
Term-
inal
size
line
and
motor
AWG
Term-
inal
size
ground
AWG
100 Vac
to 120
Vac
50/60
Hz
1-phase
FR1 2.5 10 30 30 \30 14 10 18-8 16-8
4.8 20 70 63 \70 10 8 18-8 16-8
FR2 6.9 26.4 90 63 \90 8 8 20-6 12-6
7.8 30 125 63 \125 8 6 20-6 12-6
200 Vac
to 240
Vac
50/60
Hz
1-phase
FR1 2.5 6.5 15 15 \15 14 14 18-8 16-8
4.8113030\30141018-816-8
7.8 17 60 63 \60 10 8 18-8 16-8
FR2 11 238063\8010 8 20-612-6
17.5 35 125 63 \125 8 6 20-6 12-6
FR3 25.3 49.6 200 \ \200 6 6 20-6 8-6
200 Vac
to 240
Vac
50/60
Hz
3-
phase
FR1 2.5 3.3 6 56.3 15 14 14 18-8 16-10
4.8 5.8 15 10 6.3 15 14 14 18-8 16-10
7.8 9.4 20 15 10 15 14 12 18-8 16-10
11 13.2 302016 20 12 10 18-8 16-10
200 Vac
to 240
Vac
50/60
Hz
3-phase
FR2 17.5 20.1 4030 25 30 10 10 20-6 12-8
25.3 29.1 60 40 32 45 8 10 20-6 12-8
FR3 32.2 37 70 50 40 50 8 8 20-6 10-8
FR4 48.3 53.1 100 \ \80 4 8 20-2 8-6
62.1 68.3 125 \ \100 3 6 20-2 8-6
Notes:
·Can be any UL listed types with the same ratings.

18
UL Cable Fuse Sizes (continued)
Input
voltage
Frame
size
VT/IL
current
amps
VT/IL
current
amps
Recom
mended
fuse
(Class
J, T, CF
or CC)
(max
rating)
100
kAIC①
Recom-
mended
miniature
inverse-
time
molded-
case
circuit
breaker
(max
rating)
10/14
kAIC①
Recom-
mended
Type E CMC
(max rating)
65 kAIC②
Recom-
mended
inverse-
time
molded-
case
circuit
breaker
(max
rating)
100 kAIC
(open type
only for
3-phase)①
NEC
wire
size
line
and
motor
AWG
NEC
wire
size
ground
AWG
Term-
inal
size
line
and
motor
AWG
Term-
inal
size
ground
AWG
380 Vac
to 480
Vac
50/60
Hz
3-Phase
FR1 2.2 2.6 6 4 6.3 15 14 14 18-8 16-10
4.3 5.2 10 8 6.3 15 14 14 18-8 16-10
5.6 6.7 15 10 10 15 14 14 18-8 16-10
7.6 9.1 30 15 10 15 14 10 18-8 16-10
FR2 12 14.4 302016 20 12 10 20-6 12-8
16 19.2 40 25 25 30 10 10 20-6 12-8
23 27.6 60 32 32 40 8 10 20-6 12-8
FR3 31 35.7 70 \ 40 50 8 8 20-6 10-8
FR4 38 43.7 70 \ 50 70 6 8 20-2 8-6
46 52.9 80 \ 58 80 4 8 20-2 8-6
525 Vac
to 600
Vac
50/60
Hz
3-Phase
FR2
FR3
FR4
Notes:
· Can be any UL listed types with the same ratings.
7.5
10
13.5
18
22
27
Output rating Input rating UL application

19
IEC Cable Fuse Sizes
Output rating Input rating IEC application
Input
voltage Frame size
VT/IL
current
amps
VT/IL
current
amps
Recom
mended
fuse
(max
rating)
100 kAIC
Recom-
mended
miniature
circuit
breaker
(max
rating)
10/14
kAIC
Recom-
mended
Type E
CMC
(max.
rating)
65 kAIC
Recom-
mended
circuit
breaker
(max
rating)
100
kAIC
(open
type
only for
3-phase)
IEC
cable
size
line
and
motor
mm2
IEC
cable
size
ground
mm2
Term-
inal
size
line
and
motor
mm2
Term-
inal
size
ground
mm2
100 Vac
to 120
Vac
50/60
Hz
1-phase
FR1 2.5 10 30 30 \ 30 2.5 2.5 0.2-6 1-6
4.8 20 70 63 \ 70 6 6 0.2-6 1-6
FR2 6.9 26.4 90 63 \ 90 10 10 0.5-16 1-10
7.8 30 125 63 \ 125 10 10 0.5-16 1-10
200 Vac
to 240
Vac
50/60
Hz
1-phase
FR1 2.5 6.5 15 15 \ 15 2.5 2.5 0.2-6 1-6
4.8113030\302.52.50.2-61-6
7.8 17 60 63 \ 60 6 6 0.2-6 1-6
FR2 11 23 80 63 \ 80 6 6 0.5-16 1-10
17.5 35 125 63 \ 125 10 10 0.5-16 1-10
FR3 25.3 49.6 200 \ \ 200 16 16 0.5-16 1.5-6
200 Vac
to 240
Vac
50/60
Hz
3-phase
FR1 2.5 3.3 6 5 6.3 15 2.5 2.5 0.2-6 1.5-6
4.8 5.8 15 10 6.3 15 2.5 2.5 0.2-6 1.5-6
7.8 9.4 20 15 10 15 2.5 2.5 0.2-6 1.5-6
11 13.2 30 2016 204 40.2-64-10
FR2 17.5 20.1 40 30 25 30 6 6 0.5-16 4-10
25.3 29.1 60 40 32 45 10 10 0.5-16 6-10
FR3 32.2 37 70 50 40 50 10 10 0.5-16 10-16
FR4 48.3 53.1 100 \ \ 80 25 16 0.5-35 10-16
62.1 68.3 125 \ \ 100 35 16 0.5-35 10-16

20
IEC Cable Fuse Sizes (continued)
Output rating Input rating IEC application
Input
voltage Frame size
VT/IL
current
amps
VT/IL
current
amps
Recom
mended
fuse
(max
rating)
100 kAIC
Recom-
mended
miniature
circuit
breaker
(max
rating)
10/14
kAIC
Recom-
mended
Type E
CMC
(max.
rating)
65 kAIC
Recom-
mended
circuit
breaker
(max
rating)
100
kAIC
(open
type
only for
3-phase)
IEC
cable
size
line
and
motor
mm2
IEC
cable
size
ground
mm2
Term-
inal
size
line
and
motor
mm2
Term-
inal
size
ground
mm2
380 Vac
to 480
Vac
50/60
Hz
3-Phase
FR1 2.2 2.6 6 4 6.3 15 2.5 2.5 0.2-6 1.5-6
4.3 5.2 10 8 6.3 15 2.5 2.5 0.2-6 1.5-6
5.6 6.7 15 10 10 15 2.5 2.5 0.2-6 1.5-6
7.6 9.1 30 15 10 15 2.5 2.5 0.2-6 1.5-6
FR2 12 14.4 30 20 16 20 4 4 0.5-16 4-10
16 19.2 40 25 25 30 6 6 0.5-16 4-10
23 27.6 60 32 32 40 10 10 0.5-16 4-10
FR3 31 35.7 70 \ 40 50 10 10 0.5-16 6-10
FR4 38 43.7 70 \ 50 70 16 16 0.5-35 10-16
46 52.9 80 \ 58 80 25 16 0.5-35 10-16
525 Vac
to 600
Vac
50/60
Hz
3-phase
FR2 7.5
10
13.5
FR3 18
FR4 22
27