Emerson DUNNINGTON CF3100AGW00 User manual

READ AND SAVE THESE INSTRUCTIONS
Part No. F40BP73610000 Form No. BP7361
U.L. Model No.: CF3100
Net Weight: 26.0 Lbs.
Model Numbers
DUNNINGTON™
Ceiling Fan
Owner's Manual
CF3100AGW00
Aged Walnut
CF3100BZH00
Bronze Heritage

2
WARNING
!
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power
to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and Local Electrical
Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be grounded as a
precaution against possible electrical shock. Electrical installation should be made or approved by a
licensed electrician.
3. The outlet box must be securely mounted in accordance with the manufacturer’s instructions. Use only U.L.
outlet boxes listed as “Acceptable for Fan Support”, and use the mounting screws provided with the outlet
box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and
may need to be replaced. Consult a qualified electrician if in doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with th fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed by a licensed electrician.
CAUTION: The halogen bulb operates at high internal pressure and high surface temperatures and could
shatter unexpectedly. The halogen bulb generates UV (ultraviolet) radiation that may cause skin and eye
irritation with prolonged exposure. To avoid risks of burns or other injury, assure power is off before
attempting to install or replace halogen bulb. Do not operate fan/light without lower glass in place.
6. This fan uses a halogen bulb. Do not touch the bulb with bare hands. Fingerprints may result in shorter bulb
life. Remove fingerprints with alcohol.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control
SW105, manufactured by Rhine Electric Co., Ltd.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not specifically
approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or
property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the blade
flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING: To reduce the risk of electrical shock, this fan must be installed with an isolating wall
control/switch.
DATE CODE:
The date code of this fan may be found on
the box, stamped in ink on a white label.
You should record this data above and keep
it in a safe place for future use.
U.L. Model No.: CF3100

3
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
One stepladder
One wire stripper
One Phillips head screwdriver
Three 15-watt (max.) candelabra base bulbs (not supplied)
MATERIALS
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the wire
size, to right:
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
If you feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is completed, place
a check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.
g.
d.
b.
a.
e.
c.
f.
h.
j.
k.
l.
m.
n.
HI
HI
MED
MED
LOW
LOW
FANOFF
REV
REV
LIGHT
i.
p.
o.
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
WARNING
!
WARNING
!
1. Open styrofoam unit containing fan. Remove upper
and center sections of styrofoam unit. Remove parts
and check to see that you have received the following:
a. One Fan Motor and Housing Assembly
b. One Ceiling Cover
c. Five Fan Blades
d. Five Flange Assemblies
e. Five Flange Medallion Assemblies
f. One Hanger Ball/Downrod Assembly
g. One Hanger Bracket
h. One Upper Light Kit Assembly
i. One Lower Light Kit Assembly
j. One Light Kit Glass Shade
k. One Non-Light Switch Cover
l. One Decorative Scroll Assembly
m.One SW116 Fan/Light Wall Control
(transmitter) Includes Three Covers
n. One SW105 Receiver
o. One 50-Watt (max.) Bi-Pin Halogen
(type GY8) Bulb
p. One loose parts bag containing:
1. One 5/16-18 x 1/4” setscrew
2. One 5/32" hex wrench
3. Two 8-32 x 1-1/4” threaded studs
4. Two #8-32 knurled knobs
5. Two #8 external tooth lockwashers
Tools Needed for Assembly
6. One hairpin clip
7. One clevis pin
8. Sixteen M5 x 12mm pan head screws
9. Eleven #10-32 x 14mm oval head screws
10. Eight #8-32 x 10mm flat head screw
11. Sixteen lockwashers
12. Three twist-on wire connectors
13. One balancing kit
NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
U.L. Model No.: CF3100

1. Place the flange assembly onto the blade. Place
the flange medallion assembly into the three holes
on the opposite side of the blade.
2. Secure the flange assembly and flange medallion
to the blade using the three M5 x 12mm pan head
screws and three lockwashers. Repeat for the four
remaining blades. (Figure 1)
3. Place the motor housing assembly onto the
styrofoam for blade assembly installation.
4. Align the holes in the blade flange assembly with
the holes in the motor housing.
NOTE: Take care not to scratch fan housing when
installing blades.
5. Loosely attach the flange assembly using two
#10-32 x 14mm oval head screws (supplied)
(Figure 2). Install the remaining four fan blades
assemblies using the same procedure.
6. Gently snug all flange screws to the motor
housing, working around the housing in a
clockwise sequence. Next, securely tighten all
flange screws, again working in a clockwise
sequence. Failure to follow this procedure could
result in fan wobble. This completes the blade
installation.
M5 x 12mm
PAN HEAD SCREW
(3 Per Blade)
BLADE
LOCKWASHER
(3 Per Blade)
FLANGE
ASSEMBLY
FLANGE
MEDALLION
10-32 x 14mm
OVAL HEAD SCREW
(2 Per Blade)
FLANGE
ASSEMBLY
MOTOR
HOUSING
Figure 2
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time
and remove the existing light fixture.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with national and local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
WARNING
!
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
WARNING
!
Electrical Requirements
Ceiling Fan Assembly
Procedures
To avoid possible fire or shock, follow all wiring
instructions carefully. Any electrical work not
described in these instructions should be done or
approved by a licensed electrician.
WARNING
!
4
IMPORTANT: Your ceiling fan is supplied with an
SW116 Fan/Light Wall Control (transmitter) and a
remote control SW105 Receiver which mounts
under the ceiling cover. This system allows you to
regulate your ceiling fan speed, airflow direction,
and light intensity. An optional Emerson Electric
SR110 Remote Control may also be used.
IMPORTANT: Your ceiling fan will not function
properly and may be damaged, if used with any
wall dimmer switch or control other than the
Emerson controls listed above.
Preliminary Procedures
IMPORTANT: Before assembling your ceiling fan,
refer to sections “Setting Operating Frequency of
Wall Control and Receiver” and “Installation of
Wall Control”, Page 11. These sections instruct
you how to:
a. Set the operating frequency of the fan/light wall
control and the remote control receiver.
b. Install the fan/light wall control in the wall box.
You will then be ready to proceed with the
assembly and installation of your ceiling fan.
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
WARNING
!
U.L. Model No.: CF3100
Figure 1

7. Connect the 4-pin connector from the decorative
light kit assembly to the 4-pin connector of the
switch housing (Figure 3).
8. Connect the switch housing blue wire single-pin
connector to the black wire single-pin connector
from the light kit assembly; connect the switch
housing white wire single-pin connector to the
white wire single-pin connector from the light kit
assembly (Figure 3). Be sure all wire connectors
are fully engaged.
CAUTION: Before installing and tightening the
screws, be sure there are no wires pinched
between the switch housing and the light kit
assembly.
9. Make sure all wires, single-pin and 4-pin
connectors are inside the switch housing, then
position the light kit assembly on the switch
housing so that the holes line up.
10. Attach the light kit assembly to the switch
housing using the three #8-32 x 10mm pan head
screws (supplied). Do not tighten screws at this
time. Position the light kit assembly onto the
switch housing, making sure all wires are not
pinched (Figure 4).
11. Rotate the light kit assembly clockwise to engage
the keyhole slots. Secure all three screws at this
time (Figure 4).
NOTE: Be sure wires and connectors are not
pinched under the decorative light kit assembly
before securing the light kit assembly.
5
SWITCH HOUSING BLUE
WIRE CONNECTOR
LIGHT KIT ASSEMBLY
BLACK WIRE CONNECTOR
LIGHT KIT ASSEMBLY
WHITE WIRE
CONNECTOR
SWITCH HOUSING WHITE
WIRE CONNECTOR
LIGHT KIT ASSEMBLY
SWITCH
HOUSING
4-PIN CONNECTORS
Figure 3
#8-32 x 10mm PAN
HEAD SCREWS (3)
LIGHT KIT
ASSEMBLY
KEYHOLE SLOT (2)
Figure 4
12. Carefully turn over the partially assembled ceiling
fan and place onto the flat surface of the
styrofoam.
13. Obtain the hanger ball/downrod assembly and
remove the hanger ball by loosening the
setscrew in the hanger ball until the ball falls
freely down the downrod (Figure 5). Remove the
pin from the downrod, then remove the hanger
ball. Retain the pin and hanger ball for
reinstallation in Step 24.
NOTE: The 16” downrod furnished with the
ceiling fan provides the minimum recommended
floor-to-fan blade clearance for a 9-foot ceiling.
14. Separate, untwist and unkink the black, white and
blue motor wires and the yellow uplight lead.
Route these wires through the downrod.
15. Slide the downrod down the wires and seat the
downrod in the motor coupling (Figure 6).
16. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip (Figure 6). The
clevis pin must go through the holes in the motor
coupling and the holes in the downrod. Push the
straight leg of the hairpin clip through the hole
near the end of the clevis pin until the curved
portion of the hairpin clip snaps around the clevis
pin. The hairpin clip must be properly installed to
prevent the clevis pin from working loose.
U.L. Model No.: CF3100
HANGER BALL
PIN
DOWNROD SETSCREW
Figure 5
DOWNROD
CLEVIS PIN
HAIRPIN
CLIP
SETSCREW
CLEVIS PIN
MOTOR
COUPLING
DOWNROD
HAIRPIN
CLIP
MOTOR
COUPLING SETSCREW
Figure 6

22. 16” Or Optional Longer Downrod Installation: Slide
the decorative scrolls over the 16” downrod to
rest upon the decorative upper housing
(Figure 9) To secure the decorative scrolls to the
downrod, tighten the Philips head screw in the
decorative scroll collar.
DECORATIVE
SCROLLS
16" DOWNROD
DECORATIVE
UPPER HOUSING
DECORATIVE SCROLL
COLLAR
PHILIPS HEAD
SCREW
Figure 9
6
17. Install the setscrew (supplied) in the motor
coupling and tighten using the 5/32” setscrew
wrench (supplied) (Figure 6).
18. Engage the one-pin yellow wire from the motor
housing to the one-pin black wire of the
decorative uplight kit. Engage the one-pin white
wire from the motor housing to the one-pin white
wire of the decorative uplight kit (Figure 7).
19. Carefully tuck all wires and connectors in the
decorative uplight kit assembly before placing
onto the motor housing. Align the four holes in
the decorative uplight kit assembly onto the
motor housing.
20. Secure the decorative uplight kit assembly to the
motor housing using four #8-32 x 10mm pan
head screws (supplied) (Figure 8).
21. Install three 15-watt (minimum) (not supplied)
candelabra light bulbs in the uplight sockets
(Figure 8).
MOTOR HOUSING
YELLOW WIRE
MOTOR HOUSING
WHITE WIRE
DECORATIVE
UPLIGHT KIT
ONE-PIN
CONNECTOR
DECORATIVE
UPLIGHT KIT
WHITE WIRE
DECORATIVE
UPLIGHT KIT
BLACK WIRE
Figure 7
DECORATIVE
UPLIGHT KIT
#8-32 x 10mm
PAN HEAD SCREW (4)
15-WATT (min.)
CANDELABRA
LIGHT BULBS (3)
Figure 8
23. Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 10).
24. Reinstall the hanger ball on the downrod
as follows. Route the motor leads through the
hanger ball and slide the hanger ball over the
downrod (Figure 10). Install the pin through the
holes at the top of the downrod and slide the
hanger ball up the downrod, aligning the ball so
the pin is captured in the groove in the top of the
hanger ball. Pull the hanger ball up tight against
the pin and securely tighten the setscrew in the
hanger ball. A loose setscrew could create fan
wobble.
25. The blue, black, white, and yellow leads exiting
the downrod are 80-inches long. Before installing
the fan, measure up approximately 6 to 9-inches
above the ball/downrod assembly. Cut off excess
leads and strip back insulation 1/2-inch from end
of leads.
U.L. Model No.: CF3100U.L. Model No.: CF3100
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
WARNING
!

7
How to Hang
Your Ceiling Fan
FLOOR
CEILING
AT LEAST
7'
Figure 11
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 11). Do NOT hang this
fan on an 8’ ceiling.
WARNING
!
1. Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box
(Figure 12).
U.L. Model No.: CF3100
CEILING COVER
HANGER BALL
DOWNROD
PIN
SETSCREW
Figure 10
26. You have now completed the initial assembly of
your new ceiling fan. You can now proceed with
hanging and wiring your fan.
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
WARNING
!
TWO SCREWS
SUPPLIED WITH
OUTLET BOX HANGER
BRACKET
TAB
OUTLET
BOX
Figure 12
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
WARNING
!
2. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 13). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 12).
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES
OMITTED FOR CLARITY.
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
Figure 13
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and the
hanger bracket.
WARNING
!
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!

8
OUTLET BOX
BLACK SUPPLY WIRE
BLACK/WHITE RECEIVER WIRE
BLACK FAN WIRE
BLUE FAN WIRE
BLUE RECEIVER
WIRE
YELLOW FAN WIRE
YELLOW RECEIVER WIRE
CEILING COVER
WHITE RECEIVER WIRE
WHITE FAN WIRE
WIRE CONNECTOR
RECEIVER
WHITE SUPPLY
WIRE
SUPPLY
GROUND
WIRE (GREEN
OR BARE)
HANGER BALL
GROUND WIRE
(GREEN)
HANGER BRACKET
GROUND WIRE
(GREEN)
HANGER BRACKET
BLACK RECEIVER WIRE
OPEN
PORTION OF
RECEIVER
HERE
Figure 14
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box
before wiring. All wiring must be in accordance with
National and Local codes and the ceiling fan must be
properly grounded as a precaution against possible
electrical shock.
WARNING
!
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan and light kit or receiver.
1. Pull the wire leads, coming from the end of the
downrod, and the supply wires through the open
side of the hanger bracket. (Figure 14).
2. Position the SW105 Receiver (supplied) in the
ceiling cover so that the flat side of the receiver
faces up and the open portion of the receiver is to
the right, as shown in Figure 14.
3. Using wire connectors (supplied), make wiring
connections as follows (Figure 14 and 15):
a. Connect the white fan wire and the white supply
wire to the white receiver wire (AC IN/
MOTOR N).
b. Connect the black fan wire to the black receiver
wire (TO MOTOR L).
c. Connect the black supply wire to the black/white
receiver wire (AC IN L).
d. Cut off the ends of the blue and yellow receiver
wires and strip back insulation 1/2-inch from the
ends of the wires.
e. Connect the blue fan wire to the blue receiver
wire (BOTTOM LIGHT).
f. Connect the yellow fan wire to the yellow
receiver wire (UPPER LIGHT).
g. Connect the green ground wires from the
hanger bracket and the hanger ball to the supply
ground wire (bare or green).
How to Wire Your Ceiling Fan
U.L. Model No.: CF3100

1-1/4" THREADED
STUD (2)
CEILING COVER
KNURLED KNOB (2)
LOCKWASHER (2)
HANGER
BRACKET
OUTLET
BOX
HANGER BALL/DOWNROD
ASSEMBLY
1-1/4" THREADED
STUDS (2)
HANGER
BRACKET
OUTLET BOX
RECEIVER
CEILING
COVER
Figure 16
WHITE SUPPLY WIRE
BLACK FAN WIRE
SW105 RECEIVER
WHITE FAN WIRE
BLUE RECEIVER WIRE
BLUE FAN WIRE
BLACK SUPPLY
WIRE
WHITE RECEIVER WIRE
BLACK RECEIVER WIRE
BLACK/WHITE
RECEIVER WIRE
YELLOW RECEIVER WIRE
DOWNROD
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
WARNING
!
4. After connections have been made, separate the
white and green wires from the black, blue and
yellow wires.
5. Carefully turn the wires upward and insert them up
through the open side of the hanger bracket and
into the outlet box. Push the green equipment/earth
ground and white grounded neutral wires into one
side of the outlet box; push the black, blue and
yellow ungrounded wires into the other side of the
outlet box.
Figure 15
6. Screw the two 1-1/4” threaded studs (supplied) into
the tapped holes in the hanger bracket (Figure 16).
7. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 17).
8. Secure the ceiling cover in place by installing two
lockwashers and two knurled knobs (supplied)
(Figure 26). Tighten the knurled knobs securely
until the ceiling cover fits snugly against the ceiling
and the hole in the ceiling cover is clear of the
downrod.
9. Your ceiling fan in now installed and wired and
ready for use.
Figure 17
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
WARNING
!
9U.L. Model No.: CF3100U.L. Model No.: CF3100

LIGHT KIT
ASSEMBLY
LIGHT KIT
SOCKET
50-WATT (Max.) BI-PIN
HALOGEN BULB (Type GY8)
10
2. Place the glass onto the light kit assembly aligning
the three flat areas on the top flange of the glass
shade with the three pins on the inside of the
assembly (Figure 19). Then turn the glass
clockwise until it stops turning.
3. Your ceiling fan is now installed and wire to be
controlled by your remove control system.
Figure 18
LIGHT KIT
ASSEMBLY
PIN (3)
FLAT AREA (3)
GLASS SHADE
Figure 19
1. Install the 50-watt (maximum) bi-pin (Type GY8)
halogen bulb (supplied) into the light kit socket
(Figure 18). Do not touch the glass bulb; use the
porcelain base to screw in the bulb, or wear
gloves.
CAUTION: To avoid risk of burns or other injury,
assure power is off before attempting to install or
replace the 50-watt (max.) bi-pin halogen bulb.
CAUTION: To not touch 50-watt (max.) bi-pin
halogen bulb with bare hands. Fingerprints may
result in shorter bulb life. Remove fingerprints
with alcohol.
Light Kit Installation
NOTE: Do not install the 50-watt (max.) bi-pin
halogen bulb or unhook the 50-watt (max.) bi-pin
halogen bulb from light kit socket.
1. Place the non-light switch cover onto the light kit
assembly aligning the three flat areas on the top
flange of the non-light switch cover with the three
pins on the inside of the assembly (Figure 20).
Then turn the non-light switch cover clockwise until
it stops turning.
2. Your ceiling fan is now installed and wire to be
controlled by your remove control system.
LIGHT KIT
ASSEMBLY
PIN (3)
FLAT AREA (3)
SWITCH COVER
Figure 20
If no light kit is desired, continue with non-light
switch cover installation.
Switch Cover Installation
NON-LIGHT
SWITCH COVER

The SW116 wall control transmits the command
signals via radio waves to the SW105 receiver
installed in the ceiling fan ceiling cover. The
SW105 receiver is required for the SW116 wall
control to function. Power for the SW116 wall
control comes from the 12V battery, located in the
wall control.
Replacement 12V batteries recommended are
Duracell MN21, Eveready A23, and GP23A.
1. Install the 12V battery (supplied) into the wall
control (Figure 22).
2. The SW116 wall control is supplied with a white,
ivory, or almond color cover. Choose the style that
best suits your needs and snap the cover onto the
wall control (Figure 22).
3. Install the wall control onto the outlet box using the
supplied screws (Figure 23).
4. Install decorator wall plate (purchased separately)
using the two screws provided with wall plate.
Leave wall control in “OFF” mode until fan
installation is completed (Figure 23).
12V BATTERY
WALL
CONTROL
COVER SW116 WALL
CONTROL
HI
HI
MED
MED
LOW
LOW
FAN OFF
REV
REV
LIGHT
D/L
U/L
Setting Operating
Frequency of Wall Control
and Receiver (Figure 21)
Your wall control and receiver have code switches
which must be set in one of 16 possible code
combinations. The four levers (numbered 1, 2, 3, and
4) on the switches are factory-set in the ON (up)
position. Change the switch settings as follows:
1. Slide the four switch levers in the wall control to
your choice of ON (up) or down positions. Use a
ball-point pen or small screwdriver and slide the
levers firmly up or down.
2. In the receiver, slide the four switch levers to the
same positions as set in the wall control. Make
sure the levers on both switches are in the same
positions, otherwise the fan will not operate.
ON
1234
RECEIVER SWITCH
LEVERS
ON
1234
WALL CONTROL
LEVERS
CODE
SWITCH
SW105 RECEIVER
CODE
SWITCH
SW116 WALL
CONTROL
HI
HI
MED
MED
LOW
LOW
FANOFF
REV
REV
LIGHT
Figure 21
Figure 22
SW116 WALL
CONTROL
DECORATIVE WALL PLATE
(Purchased Separately) OUTLET BOX
WALL PLATE
SCREW (2) WALL CONTROL
SCREW (2)
REV
HI
MED
LOW
FANOFF
U/L
D/L
LIGHT
Figure 23
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box.
WARNING
!
Installation
of Wall Control
11 U.L. Model No.: CF3100

Operating Your
Ceiling Fan
IMPORTANT
Fan installation must be completed, including the
installation of the fan blades, before testing of the
remote control.
Your SW116 Fan/Light Wall Control (Figure 24) has
full control of your fan, lights, and airflow direction.
1. To set the desired fan speed, push the HI, MED, or
LOW buttons to operate your fan on high, medium
or low speed (See Figure 24).
2. To reverse the direction the fan is turning, press
the REV button. The direction the fan turns will
change each time the REV button is pressed.
3. To turn your fan off, press the FAN OFF button.
4. To set the level of light brightness, press and hold
the U/L (uplight) button or the D/L (downlight)
button (if downlight kit is added to fan). The light
brightness will continue to increase then decrease
while the button is held down. When the light is at
the desired brightness, release the button.
AIRFLOW
DIRECTION
BUTTON
LIGHT
BUTTON
FAN
SPEED
BUTTONS
FAN OFF
BUTTON
RED
INDICATOR
LIGHT
FAN OFF
LOW
MED
HI
D/L
U/L
LIGHT
REV
Figure 24
5. To turn the lights on and off, press and release the
U/L (uplight) button or the D/L (downlight) button (if
downlight kit is added to fan). The lights will turn on
at the light level previously set (see Step 4).
Red light turns on when any button is pressed.
If the light does not come on, replace your battery.
INSTRUCTION TO THE USER (if device contains a digital device)
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and if no installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is not guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC
Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this
equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to
radio and TV reception. The user is cautioned that changes and modifications made to the equipment without
the approval of manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
12 U.L. Model No.: CF3100

13
Trouble Shooting
TROUBLE PROBABLE CAUSE SUGGESTED REMEDY
1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit
breakers.
WARNING: Make sure main power is turned off.
2. Loose power line connections to the fan. 2. Check line wire connections to fan
3. Fan/Light Wall Control is OFF. 3. Turn ON Fan/Light Wall Control.
4. Code switches in remote control/receiver are not 4. Check that both code switches are set in the same
set in the same position. positions.
2. Fan sounds noisy. 1. Blades not attached to fan. 1. Attach blades to fan before operating.
2 Screws holding blades to flanges are loose. 2. Tighten screws securely.
3. Fan wobbles 1. Setscrew in motor coupling is loose. 1. Raise motor cover and tighten setscrew securely.
excessively. 2. Setscrew in hanger ball/downrod assembly is 2. Tighten the setscrew in the hanger ball/downrod
loose. assembly.
3. Hanger bracket and/or ceiling outlet box is not 3. Tighten the hanger bracket screws to the outlet box,
securely fastened. and/or secure outlet box.
4. Fan blades out of balance. 4. Interchanging an adjacent (side-by-side) blade pair can
redistribute the weight and result in smoother operation.
Or use supplied balancing kit to balance blades.
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Accessories
1. Ceiling Fan Controls (see store or catalog).
2. Downrod Extension Kits (see store or catalog).
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
!
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
WARNING
!
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
WARNING
!
WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble
shooting your fan.
!
!
NOTE: Periodically check the tightness of the
knurled knobs securing the light kit glass in the
light kit adapter. Tighten if necessary.
U.L. Model No.: CF3100

14
1
8
9
10
3
2
7
5
17
31
18
19
4
6
21
11
24
23
12
22
26
27 28
15
16
30
25
14
29
HI
HI
MED
MED
LOW
LOW
FANOFF
REV
REV
LIGHT
32
20
13
13
Repair Parts
U.L. Model No.: CF3100U.L. Model No.: CF3100

15
Repair Parts Listing
Key Model Numbers
No. Description CF3100AGW00 CF3100BZH00
* Hanger Pack, Consisting of: 761655-71 761655-70
1 Hanger Bracket — —
2 Hanger Ball — —
3 Downrod - 16” — —
* Parts Bag Containing: 763518 763518
4 Pin, Clevis (1) — —
5 Clip, Hairpin (1) — —
6 Setscrew, 5/16-18 x 1/4” (1) — —
7 Setscrew Wrench, Hex. 5/32” (1) — —
8 Threaded Stud, 1-1/4” (2) — —
9 Lockwasher, External Tooth #8 (2) — —
10 Knurled Knob, #8-32 (2) — —
11 Screw, Pan Head CR M5 x 12mm (16) — —
12 Screw, Oval CR #10-32 x 14mm (11) — —
13 Screw, Pan Head #8-32 x 10mm (8) — —
14 Lockwasher (16) — —
15 Wire Connector, Twist-on (3) — —
16 Balancing Kit (1) — —
17 Cover, Ceiling (1) 763499-AGW 763499-BZH
18 Decorative Scroll Collar (1) 763500-AGW 763500-BZH
19 Decorative Scrolls (3) 763521-AGW 763521-BZH
20 Decorative Upper Housing/Upper Light
Kit Assmebly (1) 763502-AGW 763502-BZH
21 K55XL Motor (1) 762508 762508
22 Flange Assembly (5 per set) 763506-AGW 763506-BZH
23 Flange Medallion Assembly (5 per set) 763508-AGW 763508-BZH
24 Blade Assembly (5 per set) 763512-1 763512
25 Lower Light Kit Assembly (1) 763514-AGW 763514-BZH
26 Halogen, 50-Watt Bi-Pin (Type GY8) (1) — —
27 Glass Shade (1) 763516 763516
28 Non-Light Switch Cover (1) 763517-AGW 763517-BZH
29 Reverse Module 763492 763492
30 Capacitor, Aux. (1) 763522 763522
31 Receiver, Remote Control SW105 (1) 762401 762401
32 Transmitter, Remote Control SW116 (1) 763310 763310
— Owner’s Manual BP7361 BP7361
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER • PART DESCRIPTION
• NAME OF ITEM • MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone [phone].
U.L. Model No.: CF3100

Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Printed in China 01/08 Form No. BP7361
Part No. F40BP73610000 U.L. Model No.: CF3100
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson Electric Co. ceiling fan against
all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for a lifetime from the date you purchased your ceiling fan. All other
components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO
COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at
no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement
can be provided, Emerson Electric Co. will refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED
PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL,
REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP
YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized
service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort
Products, Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers
shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized
service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center.
Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible
for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any
defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and
tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral
warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson
Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND
EMERSON ELECTRIC CO. IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND
CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages as loss of time and loss of
use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was
damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.