Emerson PREMIUM CF4800AB03 User manual

READ AND SAVE THESE INSTRUCTIONS
Model No.
PREMIUM Series CROWN Series
PREMIUM &
CROWN Series
Ceiling Fan
Owner's Manual
Part No. F40BP73220000 Form No. BP7322
Net Weight: 20.0 Lbs.
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship
and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for the lifetime of your ceiling fan. All other components and accessories are covered by this
warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at no charge to
you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided, Emerson will
refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT
YOU ARE RESPONSIBLE FOR ALL COSTS OR REMOVAL, REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR RECEIPT OR
OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort Products, Division
of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers shown on the product with your
request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service
center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible for any
such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any defects,
malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral warranties apply, and
no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON IS NOT
RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES. Incidental damages include but
are not limited to such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing or
replacing other property which was damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
CF4800AB03
CF4800AGW03
CF4800AW03
CF4800BC03
CF4800BS03
CF4800BQ03
CF4800CK03
CF4800HTW03
CF4800SCB03
CF4800ORB03
CF4800PB03
CF4800PW03
CF4800TG03
CF4800WB03
CF4800WW03
CF4500AB04
CF4500AGW04
CF4500BC04
CF4500BZH04
CF4500HTW04
CF4500ORB04
CF4500WB04
U.L. Model No.: CF4800/CF4500

This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips head screwdriver One stepladder
Three wire connectors (supplied.) One wire stripper
MATERIALS
Wiring, outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of size shown
at right:
2 U.L. Model No.: CF4800/CF4500
Installed Wire Length Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible
electrical shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50
pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support”, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The downrod furnished with the fan proves the minimum recommended floor to fan blade
clearance for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with th fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do
not know enough about electrical wiring, have your fan installed by a licensed electrician.
WARNING: To avoid fire, shock or injury, do not use an Emerson Electric Co. or any other brand of
control not specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use with this product by Emerson Electric Co. Substitution
of parts or accessories not designated for use with this product by Emerson Electric Co. could
result in personal injury or property damage.
WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
WARNING
!
If you feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!

1. Open styrofoam unit containing fan. Remove top
half of styrofoam unit. Remove parts and check to
see that you have received the following:
a. Fan motor and housing assembly
b. One motor cover
c. One ceiling cover
d. Five blade flanges
e. One hanger ball/downrod assembly
f. One hanger bracket
g. One uplight lead assembly
h. One loose parts bag containing:
1. One setscrew
2. One 5/32" hex wrench
3. Eleven 10-32 x 5/8" oval head screws
4. Two 1” threaded studs
5. Two 1-1/4” threaded studs
6. Four knurled knobs
7. Three wire connectors
8. Two screws, 8-32 x 3/8"
9. Two pull chain pendant and coupling
10. One hairpin clip
11. One clevis pin
12. Two lockwashers
13. Sixteen 10-32 x 3/8" pan head screws
14. Sixteen flat washers
3 U.L. Model No.: CF4800/CF4500
Unpacking Instructions
For your convenience, check-off boxes are
provided next to each step. As each step is
completed, place a check mark in the box. This
will insure that all steps have been completed and
will be helpful in finding your place should you be
interrupted.
NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
NOTE: Fan blades are ordered separately and are
packaged in a separate carton.
CEILING
COVER
FOAM
PACKING
PROTECTIVE
PLASTIC BAG
FOAM
PACKING
CARTON
MOTOR AND
HOUSING ASSEMBLY
HANGER BALL/
DOWNROD
ASSEMBLY
HANGER
BRACKET
LOOSE
PARTS BAG
BLADE
FLANGES
MOTOR
COVER
UPLIGHT LEAD
ASSEMBLY
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
WARNING
!
WARNING
!
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
Electrical Requirements
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.
To reduce the risk of fire, electric shock, or personal injury,
mount fan to outlet box marked “Acceptable for Fan
Support”, and use screws supplied with outlet box. Most
outlet boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.
To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these instructions
should be done or approved by a licensed electrician.
Turning off wall switch is not sufficient. To avoid possible
electrical shock, be sure electricity is turned off at the main
fuse box before wiring. All wiring must be in accordance
with National and Local codes and the ceiling fan must be
properly grounded as a precaution against possible
electrical shock.
WARNING
!
WARNING
!
WARNING
!

4 U.L. Model No.: CF4800/CF4500
How To Put Your
Ceiling Fan Together
1. Position the fan motor and housing assembly in the
lower foam packing so that the top of the motor is
facing you.
2. Separate, untwist and unkink the four motor leads.
3. Obtain the hanger ball/downrod assembly and
remove the hanger ball by loosening the setscrew
in the hanger ball until the ball falls freely down the
downrod (Figure 1). Remove the pin from the
downrod , then remove the hanger ball. Retain the
pin and hanger ball for reinstallation in Step 6.
4. Route the white, blue, and black motor leads
through the downrod. Fold the yellow wire into the
slot in the motor coupling, slide the downrod down
the wires and seat the downrod in the motor
coupling (Figure 2).
5. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip (Figure 2). The
clevis pin must go through the holes in the motor
coupling and the holes in the downrod. Push the
straight leg of the hairpin clip through the hole near
the end of the clevis pin until the curved portion of
the hairpin clip snaps around the clevis pin. The
hairpin clip must be properly installed to prevent
the clevis pin from working loose. Pull on the
hanger ball to make sure the clevis pin is properly
installed.
PIN
HANGER
BALL
SETSCREW
DOWNROD
Figure 1
SETSCREW
CLEVIS PIN
MOTOR
COUPLING
DOWNROD
HAIRPIN
CLIP
MOTOR
COUPLING
HAIRPIN
CLIP
CLEVIS
PIN
DOWNROD
BROWN LEAD
RED LEAD
CLEVIS PIN
YELLOW LEAD
FROM UPLIGHT
YELLOW LEADS
Figure 2
6. Install the setscrew (supplied in loose parts bag) in
the motor coupling and tighten using the 5/32"
setscrew wrench (supplied) (Figure 3).
7. Screw two 1” threaded studs (provided) into the
motor (Figure 4). Leave approximately 7/8” of the
stud extending above the motor. Slide the motor
cover over the downrod and rotate the cover until
the threaded studs protrude; install two knurled
knobs (supplied) to secure the cover.
NOTE: Make sure the red and brown leads are
capped with wire connectors. Make sure the red,
brown, and yellow wires and wire connectors are
completely inside motor coupling cover and not
pinched between the motor coupling cover and
motor.
8. Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 5).
9. Reinstall the hanger ball on the downrod as
follows. Route the motor leads through the hanger
ball and slide the hanger ball over the downrod
(Figure 5). Install the pin through the holes at the
top of the downrod and slide the hanger ball up
the downrod, aligning the ball so the pin is
captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin
and securely tighten the setscrew in the hanger
ball. A loose setscrew could create fan wobble.
DOWNROD
SETSCREW
Figure 3
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
WARNING
!
7/8"
RED LEAD
WIRE
CONNECTORS
KNURLED KNOB
1" THREADED
STUD
MOTOR
MOTOR
COUPLING
COVER
WIRE CONNECTOR
YELLOW LEADS
BROWN LEAD
Figure 4

5 U.L. Model No.: CF4800/CF4500
10.The blue, black and white leads exiting the
downrod are 80-inches long. Before installing fan,
measure up approximately 6 to 9-inches above the
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened.
Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.
WARNING
!
SETSCREW
DOWNROD
PIN
HANGER BALL
CEILING COVER
Figure 5
11.Use three 10-32 x 3/8" pan head screws and flat
washers (supplied) to secure flange to blade
(Figure 6). Repeat for the remaining four blades.
12.Use the 10 round recessed holes in the motor hub
marked with "5" and install the five blade
assemblies (ordered separately) in accordance
with Step 13.
13.Attach one blade assembly to the motor hub using
two 10-32 x 5/8" oval head screws (supplied)
(Figure 7). Do not tighten completely at this time.
Install remaining blade assemblies in the same
way. Gently snug all flange screws to the motor
hub, working around the hub in a clockwise
sequence. Next, securely tighten all flange screws,
again working in a clockwise sequence. Failure to
follow this procedure could result in fan wobble.
This completes the blade installation.
BLADE
BLADE
FLANGE
10-32 x 3/8"
PAN HEAD
SCREW (3)
FLAT WASHER (3)
Figure 6
14. Securely attach the hanger bracket to the outlet
box using the two screws supplied with the outlet
box (Figure 9).
15. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 10). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 9).
CEILING
FLOOR
AT LEAST
7'
Figure 8
10-32 x 5/8" OVAL HEAD SCREWS
(2 PER BLADE ASSEMBLY)
Figure 7
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
WARNING
!
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 8).
WARNING
!
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
WARNING
!
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
WARNING
!
The outlet box and joist must be securely mounted
and capable of supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable for Fan
Support”.
WARNING
!

c. Securely connect the blue wire from the
downrod to the supply red (hot) wire using
wire connector (supplied). After connections
have been made, turn leads upward and
carefully push leads into the outlet box, with
the white and green leads on one side of the
outlet box and the black, blue and yellow leads
on the other side of the outlet box.
17. Screw the two 1-1/4” threaded studs (provided)
into the tapped holes in the hanger bracket.
18. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 12).
19. Secure the ceiling cover in place by sliding
lockwashers over the threaded studs and
installing the two knurled knobs (supplied).
(Figure 12.) Tighten the knurled knobs securely
until the ceiling cover fits snugly against the
ceiling and the hole in the ceiling cover is clear of
the pipe.
20. Screw in three candelabra base lamps into the
uplight sockets on top of the fan housing
assembly. Maximum lamp wattage as follows:
CF4500 - 25-watt max., CF4800 - 40-watt max.
21. Connect the pendant and chain (supplied) to the
switch pull chain using the coupling (supplied).
16. For a wall control installation you will need a
three-wire (with ground) conductor cable between
the ceiling and wall outlet boxes. This will allow
you to control the fan separately from the lights.
Figure 11 is a basic wiring diagram that will
control the uplight and downlight on a switch and
the fan on a separate control. Refer to the
installation instructions and wiring diagrams
supplied with the Emerson Fan Control Owner’s
Manual.
a. Connect the green grounding lead from the
hanger ball and the green grounding lead from
the hanger bracket to the grounding conductor
of supply (this may be a bare wire or a wire
with green colored insulation). Securely
connect wires with wire connector supplied.
b. Securely connect the white wire from the
downrod to the supply white (neutral) wire
using wire connector supplied. Securely
connect the black wire from the downrod to
the supply black (hot) wire using wire
connector supplied.
TWO SCREWS
SUPPLIED WITH
OUTLET BOX HANGER
BRACKET
TAB
OUTLET
BOX
OUTLET
BOX
HANGER
BRACKET
HANGER BALL/
DOWNROD ASSEMBLY
NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.
Figure 9
Figure 10
6 U.L. Model No.: CF4800/CF4500
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
WARNING
!
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
NOTE: If you are not sure if the outlet box is
grounded, contact a licensed electrician for advice,
as it must be grounded for safe operation.
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.
WARNING
!
WARNING
!
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
WARNING
!
BLACK BLACK FAN WIRE
LISTED OUTLET BOX
LIGHT
CONTROL
GREEN WIRE
(GROUND)
FROM
HANGER
BRACKET TO 120
VOLT
SUPPLY
WHITE
GROUND GROUND
GREEN WIRE (GROUND)
FROM HANGER BALL
LISTED WIRE CONNECTOR (4)
GROUND
WIRE WHT.
EMERSON FAN CONTROL
BLACK
(HOT)
BLUE
RED
THREE - CONDUCTOR CABLE
WITH GROUND BETWEEN
CEILING AND WALL OUTLET
BOXES
Figure 11
1-1/4"
THREADED
STUD
LOCKWASHERS (2)
CEILING COVER
KNURLED KNOB
Figure 12
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box and
not pinched between the ceiling cover and the ceiling.
WARNING
!

7 U.L. Model No.: CF4800/CF4500
Using Your Ceiling Fan
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box.
2. When controlled by a wall switch check the
operation of the fan by gently pulling on the 4-
position speed control pull chain switch. (This
switch has the longer pull chain.) The operating
sequence is as follows:
THREE-SPEED
1st Pull—HIGH
2nd Pull—Medium
3rd Pull—Low
4th Pull—OFF
3.When operated by an Emerson Remote Control,
check operation of fan and light in accordance with
the Remote Control Owner’s Manual.
4. If airflow is desired in opposite direction, turn your
fan off and wait for the blades to stop turning. Then
slide the reversing switch to the opposite position
and turn fan on again. The fan blades will turn in
the opposite direction and reverse the airflow.
Attaching Light Kit
To install an Emerson accessory light kit, remove the
three screws securing the switch cup assembly to the
fan, remove the switch cup assembly, and disconnect
the connector. Remove the screw plug from the
bottom of the switch cup and install the light kit in
accordance with the Emerson light kit Owner's
Manual.
SPEED
CONTRO
L
SWITCH
REVERSIBLE
SWITCH
TM
To avoid possible electrical shock, be sure electricity
is turned off at the main service box before wiring.
WARNING
!
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
WARNING
!
Accessories
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
1. Ceiling Fan Light Kits (see store or catalog).
2. Ceiling Fan/Light Controls (see store or catalog).
3. Downrod Extension Kits (see store or catalog).
WARNING
!
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
WARNING
!

Trouble Shooting
TROUBLE PROBABLE CAUSE SUGGESTED REMEDY
1.Fan will not start. 1.Fuse or circuit breaker blown. 1.Check main and branch circuit fuses or
circuit breakers.
WARNING: Make sure main power is
turned off.
2.Loose power line connections to the fan, 2.Check line wire connections to fan and
or loose switch wire connections in the switch wire connections in the switch
switch housing. housing.
2.Fan sounds noisy. 1.Blades not attached to fan. 1.Attach blades to fan before operating.
2.Loose screws in motor housing. 2.Check to make sure all screws in motor
housing are snug (not over-tight).
3.Screws securing fan blade flanges to 3.Check to make sure the screws which
motor hub are loose. attach the fan flanges to the motor hub
are tight.
WARNING: Make sure main power is
turned off.
4.Wire connectors inside switch housing 4.Check to make sure wire connectors in
rattling. switch housing are not rattling against
each other or against the interior wall of
the switch housing.
5.Screws holding blades to flanges are loose. 5.Tighten screws securely.
3.Fan wobbles 1.Setscrew in motor coupling is loose. 1.Raise motor cover and tighten setscrew
excessively. securely.
2.Setscrew in hanger ball/downrod assembly 2.Tighten the setscrew in the hanger ball/
is loose. downrod assembly.
3.Screws securing fan blade flanges to motor 3.Check to be sure screws which attach
hub are loose. the fan blade flanges to the motor hub
are tight.
4.Fan blade flanges not seated properly. 4.Check to be sure the fan blade flanges
seat firmly and uniformly to the surface
of the motor hub. If flanges are seated
incorrectly, loosen the flange screws and
retighten according to Steps 12 and 13
in the Assembly Instructions.
5.Hanger bracket and/or ceiling outlet box 5.Tighten the hanger bracket screws to the
is not securely fastened. outlet box, and/or secure outlet box.
6.Fan blades out of balance. 6.Interchanging an adjacent (side-by-side)
blade pair can redistribute the weight
and result in smoother operation. Or use
supplied balancing kit to balance blades.
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER
BEFORE TROUBLE SHOOTING YOUR FAN.
8 U.L. Model No.: CF4800/CF4500
!
!
!

Repair Parts
9 U.L. Model No.: CF4800/CF4500
Before discarding packaging material,
be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE
THE FOLLOWING INFORMATION:
• NAME OF ITEM
• MODEL NUMBER
• THE PART NUMBER
• THE PART DESCRIPTION
For repair parts, phone [phone].
6
13
1
2
3
16
14
15
7
10
20
19
9
21
22
8
24
18
17
54
23
27
12
11
29
30
25
26
31
18
28
TM
32
11
12
33

PREMIUM Series Repair Parts List
Ref. PREMIUM Series
No. Description CF4800WW03 CF4800AB03 CF4800PB03 CF4800HTW03 CF4800AGW03 CF4800BQ03 CF4800BS03 CF4800ORB03
Hanger Pack, 761655 761655-3 761655-2 761655-12 761655-40 761655-19 761655-17 761655-32
containing:
1 Bracket, Hanger (1) — — — — — — — —
2 Hanger Ball Assembly (1) — — — — — — — —
3 Downrod (1) — — — — — — — —
6 Cover, Ceiling 761620 761620-3 761620-2 761620-12 761620-35 761620-28 761620-25 761620-33
7 Hub, Rubber 760601 760601 760601 760601 760601 760601 760601 760601
8 Blade Assembly *** * * ***
(Full set for one fan)
9 Flange Set 761317-23 761317-24 761317-25 761317-26 761317-40 761317-28 761317-29 761317-39
(Full set for one fan)
10 Switch Cup 761991 761991-2 761991-3 761991-5 761991-20 761991-7 761991-6 761991-18
13 Cover, Motor 761621 761621-3 761621-2 761621-12 761621-26 761621-19 761621-15 761621-25
23 Motor 762508 762508 762508 762508 762508 762508 762508 762508
Parts Bag, containing: 761629-3 761629-1 761629 761629-3 761629-1 761629-1 761629-3 761629-1
4 Pin, Clevis (1) — — — — — — — —
5 Clip, Hairpin (1) — — — — — — — —
11 Coupling (2) — — — — — — — —
12 Pendant (2) — — — — — — — —
14 Wire Connector (3) — — — — — — — —
15 Wrench, Setscrew (1) — — — — — — — —
16 Stud, Threaded, 1-1/4” (2) — — — — — — — —
17 Lockwasher (2) — — — — — — — —
18 Knob, Knurled (4) — — — — — — — —
19 Screw, 10-32 x 5/8" (11) — — — — — — — —
20 Screw, 8-32 x 3/8" (2) — — — — — — — —
21 Screw, 10-32 x 3/8" (16) — — — — — — — —
22 Washer, Flat (16) — — — — — — — —
27 Setscrew, (1) — — — — — — — —
31 Stud, Threaded, 1” (2) — — — — — — — —
24 Auxiliary Capacitor 762242 762242 762242 762242 762242 762242 762242 762242
25 Cover, Switch Cup 760671-2 760671 760671-1 760671-14 760671-26 760671-19 760671-6 760671-25
26 Harness 761450-8 761450-2 761450 761450-8 761450-2 761450-2 761450-1 761450-2
28 Screw, #8 Washerhead,
8-32 x 3/8” (4) — — — — — — — —
29 Washer, 9/16” — — — — — — — —
30 Lockwasher, 9/16” — — — — — — — —
32 Uplight Lead Assembly 761790 761790 761790 761790 761790 761790 761790 761790
33 Switch Uplight 761993-1 761993-2 761993 761993-1 761993-2 761993-2 761993-1 761993-2
— Owner's Manual BP7322 BP7322 BP7322 BP7322 BP7322 BP7322 BP7322 BP7322
*Contact your nearest authorized Emerson fan dealer for replacement B52 blade accessories.
10 U.L. Model No.: CF4800/CF4500

PREMIUM Series Repair Parts List
Ref. PREMIUM Series
No. Description CF4800SCB03 CF4800TG03 CF4800AW03 CF4800WB03 CF4800PW03 CF4800CK03 CF4800BC03
Hanger Pack, 761655-9 761655-13 761655-21 761655-20 761655-22 761655-23 761655-24
containing:
1 Bracket, Hanger (1) — — — — — — —
2 Hanger Ball Assembly (1) — — — — — — —
3 Downrod (1) — — — — — — —
6 Cover, Ceiling 761620-9 761620-23 761620-29 761620-26 761620-30 761620-31 761620-32
7 Hub, Rubber 760601 760601 760601 760601 760601 760601 760601
8 Blade Assembly ** * * * **
(Full set for one fan)
9 Flange Set 761317-27 761317-30 761317-32 761317-33 761317-34 761317-36 761317-37
(Full set for one fan)
10 Switch Cup 761991-9 761991-8 761991-12 761991-13 761991-14 761991-15 761991-16
13 Cover, Motor 761621-9 761621-13 761621-20 761621-17 761621-21 761621-22 761621-23
23 Motor 762508 762508 762508 762508 762508 762508 762508
Parts Bag, containing: 761629-1 761629-1 761629-3 761629-1 761629-1 761629-3 761629-1
4 Pin, Clevis (1) — — — — — — —
5 Clip, Hairpin (1) — — — — — — —
11 Coupling (2) — — — — — — —
12 Pendant (2) — — — — — — —
14 Wire Connector (3) — — — — — — —
15 Wrench, Setscrew (1) — — — — — — —
16 Stud, Threaded, 1-1/4” (2) — — — — — — —
17 Lockwasher (2) — — — — — — —
18 Knob, Knurled (4) — — — — — — —
19 Screw, 10-32 x 5/8" (11) — — — — — — —
20 Screw, 8-32 x 3/8" (2) — — — — — — —
21 Screw, 10-32 x 3/8" (16) — — — — — — —
22 Washer, Flat (16) — — — — — — —
27 Setscrew, (1) — — — — — — —
31 Stud, Threaded, 1” (2) — — — — — — —
24 Auxiliary Capacitor 762242 762242 762242 762242 762242 762242 762242
25 Cover, Switch Cup 760671-15 760671-16 760671-20 760671-18 760671-21 760671-22 760671-23
26 Harness 761450-2 761450-2 761450-8 761450-2 761450-2 761450-8 761450-2
28 Screw, # 8 Washerhead,
8-32 x 3/8” (4) — — — — — — —
29 Washer, 9/16” — — — — — — —
30 Lockwasher, 9/16” — — — — — — —
32 Uplight Lead Assembly 761790 761790 761790 761790 761790 761790 761790
33 Switch Uplight 761993-2 761993-2 761993-1 761993-2 761993-2 761993-1 761993-2
— Owner's Manual BP7322 BP7322 BP7322 BP7322 BP7322 BP7322 BP7322
*Contact your nearest authorized Emerson fan dealer for replacement B52 blade accessories.
11 U.L. Model No.: CF4800/CF4500

CROWN Series Repair Parts List
Ref. CROWN Series
No. Description CF4500AB04 CF4500AGW04 CF4500HTW04 CF4500BC04 CF4500WB04 CF4500ORB04 CF4500BZH04
Hanger Pack, 761655-3 761655-40 761655-12 761655-24 761655-20 761655-32 761655-41
containing:
1 Bracket, Hanger (1) — — — — — — —
2 Hanger Ball Assembly (1) — — — — — — —
3 Downrod (1) — — — — — — —
6 Cover, Ceiling 761620-3 761620-35 761620-12 761620-32 761620-26 761620-33 761620-36
7 Hub, Rubber 760601 760601 760601 760601 760601 760601 760601
8 Blade Assembly ** ** ** *
(Full set for one fan)
9 Flange Set 761845-5 761845-12 761845-7 761845-9 761845-11 761845-10 761845-13
(Full set for one fan)
10 Switch Cup 761991-2 761991-20 761991-5 761991-16 761991-13 761991-18 761991-21
13 Cover, Motor 761621-3 761621-26 761621-12 761621-23 761621-17 761621-25 761621-27
23 Motor 762508 762508 762508 762508 762508 762508 762508
Parts Bag, containing: 761629-1 761629-1 761629-3 761629-1 761629-1 761629-1 761629-1
4 Pin, Clevis (1) — — — — — — —
5 Clip, Hairpin (1) — — — — — — —
11 Coupling (2) — — — — — — —
12 Pendant (2) — — — — — — —
14 Wire Connector (3) — — — — — — —
15 Wrench, Setscrew (1) — — — — — — —
16 Stud, Threaded, 1-1/4” (2) — — — — — — —
17 Lockwasher (2) — — — — — — —
18 Knob, Knurled (4) — — — — — — —
19 Screw, 10-32 x 5/8" (11) — — — — — — —
20 Screw, 8-32 x 3/8" (2) — — — — — — —
21 Screw, 10-32 x 3/8" (16) — — — — — — —
22 Washer, Flat (16) — — — — — — —
27 Setscrew, (1) — — — — — — —
31 Stud, Threaded, 1” (2) — — — — — — —
24 Auxiliary Capacitor 762242 762242 762242 762242 762242 762242 762242
25 Cover, Switch Cup 760671 760671-26 760671-14 760671-23 760671-18 760671-25 760671-27
26 Harness 761450-2 761450-2 761450-8 761450-2 761450-2 761450-2 761450-2
28 Screw, #8 Washerhead,
8-32 x 3/8” (4) — — — — — — —
29 Washer, 9/16” — — — — — — —
30 Lockwasher, 9/16” — — — — — — —
32 Uplight Lead Assembly 761790 761790 761790 761790 761790 761790 761790
33 Switch Uplight 761993-2 761993-2 761993-1 761993-2 761993-2 761993-2 761993-2
— Owner's Manual BP7322 BP7322 BP7322 BP7322 BP7322 BP7322 BP7322
*Contact your nearest authorized Emerson fan dealer for replacement B52 blade accessories.
Printed in China 09/07
Part No. F40BP73220000 Form No BP7322
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100W.Florissant• St.Louis, MO63136
U.L. Model No.: CF4800/CF4500