Emerson MRLDS-250 User manual

1
SUPPORT CENTER ADVISORY
Local User’s Guide
MRLDS –250 to Multiflex I/O
By Emerson Commercial and Residential Solutions

2
SUPPORT CENTER ADVISORY
Contents
Basic Set Up.......................................................................................................................................................................... 3
A. Overview..................................................................................................................................................................... 3
B. How to Set Up Analog Output Type of MRLDS-250 ........................................................................................... 3
C. How to Set Multiflex Input point for MRLDS - 250................................................................................................ 4
D. How to Set the Input Type on E2 Controller for MRLDS –250......................................................................... 5
E. How to Associate the MRLDS –250 on a Sensor Control............................................................................... 10
F. How to Disable E2 applications when MRLDS –250 is in Alarm condition................................................... 15
1. Add Digital Sensor Control................................................................................................................................ 15
2. For Standard Circuit ........................................................................................................................................... 21
3. For Case Control Circuit .................................................................................................................................... 24
4. For XM Circuit...................................................................................................................................................... 26
G. Maintenance Requirements .............................................................................................................................. 29
1. Bump Testing....................................................................................................................................................... 29
2. Gas Detector Response Adjustment................................................................................................................ 30
H. Troubleshooting................................................................................................................................................... 31
1. Fault Codes.......................................................................................................................................................... 31
2. Diagnostic Attributes........................................................................................................................................... 32
3. Device Reads Incorrect PPM............................................................................................................................ 33

3
SUPPORT CENTER ADVISORY
Basic Set Up
A. Overview
•The MRLDS –250 provides an Analog Output signal that is proportional to the level of gas
detected.
•The Default will 1-5V but it can be set as follows: 4-20mA; 0-5V; 0-10V; 2-10V.
•No Jumpers or hardware switch settings are required to configure the Analog Output Type.
This is done electronically from the front panel display.
•Press and hold the information button for five seconds to activate the parameter list.
•Each parameter is shown in turn by using the UP or DOWN buttons. The parameter
is shown as P.-XX, with XX being the parameter value. Pressing Enter while a
parameter is displayed allows the attributes of the parameter to be set. Each Parameter has
its own attributes, as shown in the following table. Set the attributes as desired, and then press
Enter to save the setting.
B. How to Set Up Analog Output Type of MRLDS-250
1. For Address, look for P.-03 on the parameter list then press Enter button.
2. Set the desired type by pressing Up or Down with the type was designated as
follows:
➢00 Selects 0-5V
➢01 Selects 1-5V (Default)
➢02 Selects 0-10V
➢03 Selects 2-10V
➢04 Selects 4-20mA
3. Press Enter button to Save.
4. For Scaling, look for P.-16 on the parameter list then press Enter button.
5. This will allow the user to select the full-scale PPM value that represents the maximum analog
output (for example 1000PPM = 5V when 1-5V was selected on P.-03). Use the Up or
Down to adjust the value and set it to 1000PPM.
6. Press Enter to save the setting.

4
SUPPORT CENTER ADVISORY
C. How to Set Multiflex Input point for MRLDS - 250
1. An input point on a Multiflex board consists of two terminals. One of these terminals,
labeled as “SIG” reads the signal from the sensor, while the other, labeled “0v” is where
the sensor’s ground wire is connected.
2. The Analog Output Signal (+) should go to (SIG) terminal of the Multiflex board and the
Ground (GND) should go to (0v) terminal of the board.
3. The Dip Switch setting of the Multiflex board for the MRLDS –250 should be in OFF
position since it supplies its own voltage signal to the point.

5
SUPPORT CENTER ADVISORY
D. How to Set the Input Type on E2 Controller for MRLDS –250
1. Log in to E2 controller by pressing and type in your Log in credentials then press
.
2. Press + or press -- to go to Input Status Screen.

6
SUPPORT CENTER ADVISORY
3. Navigate to the Board and Point of the Input where the MRLDS –250 is connected then press
for Setup. Press for Analog Type. In this Example, Board 1 Point 1 is being used.
4. Highlight Sensor Type parameter by pressing the Down Arrow Key.

7
SUPPORT CENTER ADVISORY
5. Press for Look Up and look for Linear and press to confirm.
6. Navigate down to Eng Units.

8
SUPPORT CENTER ADVISORY
7. Press for Look Up and look for PPM and press to confirm.
8. Set the Low-End Point and High-End Point depending on the range set on the MRLDS –
250 which is on P.-03 parameter. On this Example, we use the default which is the 1-5V.

9
SUPPORT CENTER ADVISORY
9. Set the Low End EU and High End EU. This will be the equivalent PPMreading of the Analog
Output given out by the device. “0” will be the Low End EU and the High End EU will be what
is set on P.-16 parameter. We should set it to 1000.
10. For the Low End Limit, set it to -10% of what is set on Low End EU and +10% of what is
set on High End EU for the High End Limit.

10
SUPPORT CENTER ADVISORY
11. Press button to save.
E. How to Associate the MRLDS –250 on a Sensor Control
1. Add an Analog Sensor Application. Press --Add Application.