EMS EC-41-0200 User manual

IDENT REV DATE
FC-610-001
EN300 200-2
0905 !
20K4K7
CN/O
20K=Red/Bl
4k7=Yellow
ANTENNA
Zone Interface Module (ZIM)
Installation Guide
Part no
EC-41-0200
Product description
Wireless Zone Interface Module
1 Pre installation 2 Components
!
Installation must conform to applicable local installation codes
and should only be installed by a fully trained competent person.
• Ensure that the device is installed as per the site survey.
• The use of a non-metallic spacer should be considered if mounting the
device on to a metal surface.
• DO NOT press the log on button on a pre-programmed device, as this
will cause communication with the control panel to be lost. Should this
happen, delete the device from the system and add it back on.
• This device contains electronics that may be susceptible to damage
from Electrostatic Discharge (ESD). Take appropriate precautions when
handling electronic boards.
3 Mounting location guidelines
4 Remove cable entry points 5 Fix to the wall
©2022 EMS Ltd. All rights reserved. Page 1 of 2 TSD142-99 Issue 7 21/06/2022 AJM
1 2 3
14x lid xing screws, 2Front lid, 3Back box
For optimum wireless
performance, the following
must be observed:
• Ensure the ZIM is not installed
within 0.6 m of the WZM.
• Ensure the ZIM is not installed
within 2 m of the control panel
or any other wireless or electrical
equipment.
• Ensure the ZIM is not installed
within 0.6 m of any metal work.
• Use all four circled
xing positions to
ensure a rm xing.
• Use suitable fasteners
and xings.
DO NOT use
Available cable
entry points
WIRELESSZONEINTERFACE MODULE
POWER
FAULT
WIRELESSZONE MONITOR
FIRE
FireAlarm Control
FIRE
FireAlarm Control
WIRELESSZONEINTERFACE MODULE
POWER
FAULT
WIRELESSZONE MONITOR
WZM
WZM
ZIM
ZIM
0.6 m
0.6 m
2 m
Existing
control panel
Existing
control panel
• Drill the cable
entry points as
necessary.
• Cable glands
should be used.
• DO NOT leave
excess cable in the
device.
WIRELESS ZONE INTERFACEMODULE
=
=
ON
INPUT
1INPUT
2
EXPAN1EXPAN2
OUTPUT
2
OUTPUT
1
IP-
IP+ IP-
IP+
3VDCSETRST
N/OCOMN/C
3VDCSETRST
N/OCOMN/C
ANTENNA
KEEP CABLES AWAYFROM THIS AREA
LOGON
OUTPUT 2OUTPUT 1
3VDC SET RST
INPUT 1I NPUT 2
LED
ENABLE
POWER
INPUT
INPUT
FAULT
CLOSED
01
1
64
F-SAFE
N/OC OM N/C
IP- IP+ IP- IP+
3VDC SET RST N/OC OM N/C
EXPAN1 EXPAN2
RELAY ON RELAY ON
2
4
8
16
32
ON
1 2 3 4 5 6 7 8
012ABC
Fixing position location
within cavity

6 Connection wiring 7 Connection wiring
8 Conguration 9 LED operation
Specication Regulatory information
©2022 EMS Ltd. All rights reserved. Page 2 of 2 TSD142-99 Issue 7 21/06/2022 AJM
Refer to the wireless zone
monitor engineers guide
(TSD143) for full wiring details.
Free to download from www.
emsgroup.co.uk
The ZIM must be added to the WZM, before adding other wireless devices to
the system.
• Refer to the wireless zone monitor
engineers guide (TSD143) for full
programming details.
Operating temperature -10 to +55 °C
Storage temperature 5 to 30 °C
Humidity 0 to 95% non-condensing
Supply 6x AA alkaline (Panasonic LR6AD Powerline /
Varta 4006 Industrial)
CAUTION!
Fitting of an incorrect battery type invalidates the product certication and may
result in poor performance.
Output rating 2A at 24 VDC
IP rating IP65
Operating frequency 868 MHz
Output transmitter power 0 to 14 dBm (0 to 25 mW)
Signalling protocol X
Dimensions (W x H x D) 120 x 240 x 60 mm
Weight 0.95 kg
Location Type A: For indoor use
Manufacturer
Year of manufacture
Certication
Certication body
CPR DoP
Approved to
European Union
Directives
0359-CPR-00436
EN54-18:2005. Fire detection and re alarm systems.
Part 18:Input/output devices.
EN54-25:2008. Incorporating corrigenda September 2010
and March 2012. Fire detection and re alarm systems.
EMS declares that this device is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.
emsgroup.co.uk
2012/19/EU (WEEE directive): Products marked with this
symbol cannot be disposed of as unsorted municipal waste
in the European Union. For proper recycling, return this
product to your local supplier upon purchase of equivalent
new equipment, or dispose of it at designated collection
points. For more information see www.recyclethis.info
Dispose of your batteries in an environmentally friendly
manner according to your local regulations.
Carrier Manufacturing Poland Sp. z o.o.
Ul. Kolejowa 24. 39-100 Ropczyce, Poland
See devices serial number label
0905
14
• When tting / replacing batteries; observe correct polarity, using only
specied batteries.
• Connect the power jumper across the PIN header.
Free to download from
www.emsgroup.co.uk
The device has six indication LEDs. Pressing the LED enable button enables
their illumination for 10 minutes before automatically timing out.
2x input fault: YELLOW LED ON = FAULT
2x input closed: RED LED ON = ACTIVE
2x output: RED LED ON = ACTIVE
3VDCS
E
INPUT 1I NPUT 2
LED
E
NABLE
PO WER
INPUT 1 INPUT 2
FAULT
CLOSED
64
F-SAFE
IP- IP+I P- IP+
EXP
A
16
32
• Once powered, reassemble the device.
device
unpowered
(pins unlinked)
device
powered
(both pins
linked)
CLOSED
FAULT
INPUT 1
INPUT 2
Input 2
LEDs
Input 1
LEDs
Output 1 LED Output 2 LED