EMS Fusion FCX-532-001 User manual

Loop Module
Installation Guide
Part no
FCX-532-001
Description
Fusion Loop Module
1 Pre installation 2 Components
!Installation must conform to applicable local installation codes
and should only be installed by a fully trained competent person.
• Ensure the loop module is installed as per the site survey.
• Refer to step 3 to ensure optimised wireless performance.
• If using remote aerials with this product, refer to the remote aerial
installation guide (MK293) for more information.
• A maximum of 5 loop modules can be connected per loop.
• This device contains electronics that may be susceptible to damage
from Electrostatic Discharge (ESD). Take appropriate precautions when
handling electronic boards.
3 Mounting location guidelines 4 Optional PCB removal
5 Remove cable entry points 6 Fix to the wall
©2024 EMS Ltd. All rights reserved. Page 1 of 2 TSD077-99 (Issue 9) 10/01/2024 AJM
POWER
FAULT
ISOLATOR
ACTIVE
FFusionusion
1 2 3 4 5
14x corner covers, 24 x lid screws, 3Loop module lid,
4Loop module PCB, 5Loop module back box
For optimum wireless
performance, the following
must be observed:
• Ensure the loop
module is not installed
within 2 m of other
wireless or electrical
equipment (not
including the control
panel).
• Ensure the loop
module is not installed
within 0.6 m of metal
work.
FIRE
FireAlarm Control
POWER
FAULT
ISOLATOR
ACTIVE
2 m
0.6 m
Loop
module
Control
panel
• Remove the three circled retaining screws, before unclipping the PCB.
TX
RADIO
WD
RESET
HELP
RX
ON
12 34 56 78
BACK
POWER
FAULT
ISOLATE
0V
RX
TX
3V
SCR
+
-
LOOP IN
SCR
LOOP OUT
+
-
1 2 3 4 5 6 7
• Drill the cable entry
points as necessary.
= DO NOT use
= Available cable
entry points
• All ve circled xing
positions are available
for use as required.
• The key hole can also
be used for locating
and xing where
required.

7 Connection wiring 8 Conguration
9 Apply power 10 Close loop module
Specication Regulatory information
©2024 EMS Ltd. All rights reserved. Page 2 of 2 TSD077-99 (Issue 9) 10/01/2024 AJM
• Loop cables should only be passed via the access points available.
• Flame retardant cable glands must be used.
• DO NOT leave excess cable inside the loop module.
Single loop module.
Multiple loop modules (max. 5)
+
-
+
-
Scr
Loop
IN
Loop
OUT
Scr
+-+-
Scr
Loop
IN
Loop
OUT
Scr
+-+-
Scr
Loop
IN
Loop
OUT
Scr
+-+-
Screen not connected
Scr
Loop
IN
Loop
OUT
Scr
+-+-
+
-
+
-Screen not connected
Control panel
Screen
Loop
OUT
Loop
IN
Control panel
Screen
Loop
OUT
Loop
IN
• Set the loop module address using the on-board 8 way switch.
• Available selections are shown in the table below.
• The system can now be programmed.
• Refer to the Fusion programming manual (TSD062) for details of compatible
FireCell devices and full programming information.
Apply power to the control panel. The normal LED states for the Loop Module
are as below:
• The green POWER LED
will illuminate.
• The other LEDs should
be extinguished.
TX
RADIO
WD
RESET
HELP
RX
ON
12 34 56 78
BACK
POWER
FAULT
ISOLATE
0V
RX
TX
3V
SCR
+
-
LOOPIN
SCR
LOOPOUT
+
-
1 2 3 4 5 6 7
POWER
FAULT
ISOLATE
• Ensure that the loop module PCB is correctly inserted and the PCB retaining
screws are retted.
• Ret the loop module lid, ensuring LEDs are not damaged by the light pipe
when retting.
POWER
FAULT
ISOLATOR
ACTIVE
Operating temperature -10 to +55 °C
Storage temperature 5 to 30 °C
Humidity 0 to 95% non-condensing
Operating voltage 17 to 28 VDC
Operating current 17 mA (typical)
91mA (max.)
IP rating IP54
Operating frequency 868 MHz
Output transmitter power 0 to 14 dBm (0 to 25 mW)
Signalling protocol X
Panel protocol XP
Dimensions (W x H x D) 270 x 205 x 85 mm
Weight 0.95 kg
Location Type A: For indoor use
Manufacturer
Year of manufacture
Certication
Certication body
CPR DoP
Approved to
European Union
Directives
EN54-17:2005. Fire detection and re alarm systems.
Part 17:Short-circuit isolators.
EN54-18:2005. Fire detection and re alarm systems.
Part 18:Input/output devices.
EN54-25:2008. Incorporating corrigenda September 2010 and
March 2012. Fire detection and re alarm systems.
EMS declares that this device is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: www.emsgroup.co.uk
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to
your local supplier upon purchase of equivalent new equipment,
or dispose of it at designated collection points. For more
information see www.recyclethis.info
Dispose of your batteries in an environmentally friendly manner
according to your local regulations.
Carrier Manufacturing Poland Sp. z o.o.
Ul. Kolejowa 24. 39-100 Ropczyce, Poland
See devices serial number label
0359-CPR-0222
0905
13
Loop module 1
Loop module 1 Loop module 2 Loop module 3
DIL
SWITCH
SETTING
DIL
SWITCH
SETTING
DIL
SWITCH
SETTING
DIL
SWITCH
SETTING
DIL
SWITCH
SETTING
Addr. 1......8 Addr. 1......8 Addr. 1......8 Addr. 1......8 Addr. 1......8
1 10000000 11 11010000 21 10101000 31 11111000 41 10010100
2 01000000 12 00110000 22 01101000 32 00000100 42 01010100
3 11000000 13 10110000 23 11101000 33 10000100 43 11010100
4 00100000 14 01110000 24 00011000 34 01000100 44 00110100
5 10100000 15 11110000 25 10011000 35 11000100 45 10110100
6 01100000 16 00001000 26 01011000 36 00100100 46 01110100
7 11100000 17 10001000 27 11011000 37 10100100 47 11110100
8 00010000 18 01001000 28 00111000 38 01100100 48 00001100
9 10010000 19 11001000 29 10111000 39 11100100 49 10001100
10 01010000 20 00101000 30 01111000 40 00010100 50 01001100
51 11001100 61 10111100 71 11100010 81 10001010 91 11011010
52 00101100 62 01111100 72 00010010 82 01001010 92 00111010
53 10101100 63 11111100 73 10010010 83 11001010 93 10111010
54 01101100 64 00000010 74 01010010 84 00101010 94 01111010
55 11101100 65 10000010 75 11010010 85 10101010 95 11111010
56 00011100 66 01000010 76 00110010 86 01101010 96 00000110
57 10011100 67 11000010 77 10110010 87 11101010 97 10000110
58 01011100 68 00100010 78 01110010 88 00011010 98 01000110
59 11011100 69 10100010 79 11110010 89 10011010 99 11000110
60 00111100 70 01100010 80 00001010 90 01011010 100 00100110
101 10100110 106 01010110 111 11110110 116 00101110 121 10011110
102 01100110 107 11010110 112 00001110 117 10101110 122 01011110
103 11100110 108 00110110 113 10001110 118 01101110 123 11011110
104 00010110 109 10110110 114 01001110 119 11101110 124 00111110
105 10010110 110 01110110 115 11001110 120 00011110 125 10111110
126 01111110