EMS FireCell FC-171-001 User manual

63 mm
THIS WAY
UP WHEN
WALL
MOUNTING
SIZE C SIZE C SIZE C
SIZE AA
SIZE AA
SIZE AA
Wireless Sounder Beacon
Installation Guide
1 Pre installation
4 Power device
Cut out section
(shaded area)
To unlock, insert a 1.5
mm allen key to depress
the locking clip and turn
anticlockwise to release
as shown.
Unclip the battery retaining plate from the wireless module.
When fitting / replacing batteries; observe correct polarity,
using only specified batteries.
Connect the power jumper across the PIN header.
FC-171-001
FC-171-002
FC-315-CA1
FC-315-CA2
FC-315-WA1
FC-315-WA2
White Wireless Sounder Base Only [2]
Red Wireless Sounder Base Only [2]
White Ceiling Sounder Beacon Only [1]
Red Ceiling Sounder Beacon Only [1]
White Wall Sounder Beacon Only [1]
Red Wall Sounder Beacon Only [1]
3 Fix mounting plate
2 Components
Part no Product description
device
unpowered
(pins unlinked)
device
powered
(both pins linked)
!
Installation must conform to applicable local installation
codes and
should only be installed by a fully trained
competent person.
Ensure that the device is installed as per the site survey.
The use of a non-metallic spacer should be considered if
mounting the device on to a metal surface.
Do NOT Press the Log On button on a pre-programmed device,
as this will cause communication with the Control Panel to be
lost. Should this happen, delete the device from the system
and add it back on.
This device contains electronics that may be susceptible to
damage from Electrostatic Discharge (ESD). Take
appropriate precautions when handling electronic boards.
4
Remove the mounting plate by turning the device
ANTICLOCKWISE, to release it from the mounting plate.
3
5 Optional device locking 6 Configuration
To lock the Sounder
Beacon into the wireless
module, remove the cut
out section as shown.
Use both mounting holes.
Use suitable fasteners and fixings.
Once powered, reassemble the device.
When wall mounting, ensure the mounting plate is fitted in the
orientation shown.
See the Specification section for compliance information.
CPR
Sounder beacon Wireless module
Mounting plateBattery retaining plate
1
4
2
3
©2021 EMS Ltd. All rights reserved Page 1 of 2 TSD066-99 Iss 8 23/11/2021 AJM
Example shown:
FC-315-CA1
FC-171-001
12
The device’s loop address is configured within the user interface’s
menu structure.
Refer to the programming manual for full programming details.
Free to download from
www.emsgroup.co.uk
FireCell = MK98
Fusion = TSD062
WZM = TSD143

1 2 3 4 5
1 2 3 4 5
O-O-O-O-O
18
O-O-O-O-|
1
O-O-O-|-O
1
O-O-O-|-|
O-O-|-O-O
O-O-O-|-|
1
O-O-|-O-|
1
O-O-|-|-|
9
O-|-O-O-O
1
O-|-O-O-|
19
O-|-O-|-O
1
O-|-O-|-|
1
O-|-|-O-O
1
O-|-|-O-|
18
O-|-|-|-O
1
O-|-|-|-|
1
|-O-O-O-O
1
|-O-O-O-|
1
|-O-O-|-O
18
|-O-O-|-|
19
|-O-|-O-O
19
|-O-|-O-|
1
|-O-|-|-O
1
|-O-|-|-|
1
|-|-O-O-O
1
|-|-O-O-|
18
|-|-O-|-O
18
|-|-O-|-|
1
|-|-|-O-O
1
|-|-|-O-|
1
|-|-|-|-O
1
|-|-|-|-| 8
Operating temperature -10 to +55 °C
Storage temperature 5 to 30 °C
Humidity 0 to 95% non-condensing
Supply 3x AA alkaline (Panasonic LR6AD Powerline / Varta 4006
Industrial) 3x C alkaline (Panasonic LR14AD Powerline / Varta
4014 Industrial)
CAUTION!
Fitting of an incorrect battery type invalidates the product certification and may result in poor
performance.
Sounder output 94 to 97 dB(A) at 1 m (as dispatched).
Low setting reduces volume by 7 dB.
IP rating IP54
Operating frequency 868 MHz
Output transmitter
power Auto adjusting 0 to 14 dBm (0 to 25 mW)
Beacon element voltage 17 to 60 VDC operating at 18 VDC
Beacon element
current (max.) 45 mA at 1 Hz flash rate
Flash rate 0.5 Hz / 1 Hz (selectable)
Beacon
coverage C-3-15 (ceiling mounted variant)
W-3.1-11.3 (wall mounted variant)
Dimensions (Ø x D) 120 x 145 mm
Weight 0.65 kg
Location Type A: For indoor use
Carrier Manufacturing Polska Sp. Z o.o. Ul. Kolejowa 24.
39-100 Ropczyce, Poland
Manufacturer
Year of manufacture See devices serial number label
2012/19/EU (WEEE directive):
Products marked with this symbol cannot be disposed of as
unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon
purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see
www.recyclethis.info
Dispose of your batteries in an environmentally friendly
manner according to your local regulations.
European Union
directives
EMS declares that this device is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address:
www.emsgroup.co.uk
Approved to
See part listing for associated products:
EN54-3:2001. Incorporating Amendments Nos. 1 and 2. Fire
detection and fire alarm systems. Part 3: Fire alarm devices -
Sounders. [1]
EN54-23:2010. Fire detection and fire alarm systems. Part
23: Fire alarm devices. Visual alarm devices. [1]
EN54-25:2008. Incorporating corrigenda September 2010
and March 2012. Fire detection and fire alarm systems. Part
25: Components using radio links. [2]
Certification
Certification body
CPR DoP 0359-CPR-00292
Configuration continued
ON
12345 6 7
Sounder Beacon
All 32 available
configurations are shown
in the tone table.
ON
OFF
7
7
ON
OFF
ON
7
ON
7
OFF
OFF
6
6
6
6
SWITCHES
6 & 7
VOLUME
HIGH
FLASH
RATE
HIGH
1Hz
1Hz
0.5Hz
0.5Hz
LOW
LOW
ON
12345 6 7
Sounder Beacon
Volume/flash rate (Set on sounder beacon)
Audio monitoring (Set on wireless module)
Switches 6 and 7 are used to configure the
volume and flash rate.
www.emsgroup.co.uk
Wireless Sounder Base
PRESS HERE TO
LOG ON
IDENT
ON
OFF
2
2
ON
OFF
ON
2
ON
1
1
1
SWITCHES
1 & 2
PRIMARY
TONE
MONITORED
SECONDARY
TONE
MONITORED
The primary and secondary stage sounder
tones can be monitored. If enabled and no
audio is detected within 10 seconds upon
sounder activation, a fault is indicated at the
control panel.
OFF
OFF
Sounder tone (Set on sounder beacon)
Default setting: primary tone 5
Default setting: high volume / 1 Hz flash rate
Default setting: audio monitoring disabled
18
1
1
1
4
1
1
9
1
19
1
1
1
18
1
1
1
1
18
19
19
1
1
1
1
18
18
1
1
1
1
8
SECONDARY
TONE
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
TONE TYPE TONE DESCRIPTION / APPLICATION
1. 970Hz
2. 800Hz/970Hz @ 2Hz
800Hz - 970Hz @ 1Hz
970Hz 1s OFF / 1s ON
970Hz, 0.5s / 630Hz, 0.5s
554Hz, 0.1s / 440Hz, 0.4s (AFNOR NF S 32 001)
500 - 1200Hz, 3.5s / 0.5s OFF (NEN 2575:2000)
8.
420Hz 0.625s ON / 0.625s OFF (Australia AS1670 Alert tone)
9.
500 - 1200Hz, 0.5s / 0.5s OFF x 3 / 1.5s OFF (AS1670 Evacuation)
550Hz / 440Hz @ 0.5Hz
970Hz, 0.5 ON / 0.5s OFF x 3 / 1.5s OFF (ISO 8201)
2850Hz, 0.5s ON / 0.5s OFF x 3 / 1.5s OFF (ISO 8201)
1200Hz - 500Hz @ 1Hz (DIN 33 404)
14. 400Hz
550Hz, 0.7s / 1000Hz, 0.33s
1500Hz - 2700Hz @ 3Hz
17. 750Hz
18. 2400Hz
19. 660Hz
660Hz 1.8s ON / 1.8s OFF
660Hz 0.15s ON / 0.15s OFF
510Hz, 0.25s / 610Hz, 0.25s
800 / 100Hz 0.5s each (1Hz)
250Hz - 1200Hz @ 12Hz
500Hz - 1200Hz @ 0.33Hz
2400Hz - 2900Hz @ 9Hz
2400Hz - 2900Hz @ 3Hz
800Hz - 970Hz @100Hz
800Hz - 970Hz @ 9Hz
800Hz - 970Hz @ 3Hz
800Hz, 0.25s ON / 1s OFF
500Hz - 1200Hz, 3.75s / 0.25s OFF (AS2220)
PRIMARY
TONE
Switches 1-5 on the 7 way switch are used to
configure the sounder tone.
1 2 3 4 5
ON
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
12 3 4
ON
5
ON
1 2 3 4 5
SWITCHES
1-5
0905
14
Specification Regulatory Information
©2021 EMS Ltd. All rights reserved Page 2 of 2 TSD066-99 Iss 8 23/11/2021 AJM