Emtek EMPowered in8-empwrunty User manual

EMPoweredTM Motorized Touchscreen
Works with Yale Access
Keypad Smart Lock Deadbolt
WORKS
WITH

2
What’s in
the box
x3
#8-32 x 5/16”
Machine Screws
x4

Wood Screws
x2

Machine Screws x2
#10 x 3”
Wood Screws

Cover

Plate
Security PlateStrike Plate
AA x4

Connect Wi-Fi

DoorSense™
Interior
Escutcheon
Deadbolt Latch
2-3/8”
Deadbolt Latch
2-3/4”

3
Door Prep
Door Jamb Prep
2-3/8” or 2-3/4” Backset
2-1/8” Diameter Bore
1/8” Deep
2-1/4”
1”
1” Diameter Edge Bore
3/16” Deep
2-3/4”
1-1/8”
3/4”
1-1/4”
1-1/4” Deep

4
Install Latch & Strike Plate
!
1
Note: Use only the
supplied latch for proper

!
Bolt must be in retracted




5
Install Touchscreen Escutcheon
2
Outside of the door Inside of the door

6
Install Interior Mounng Plate
3
Loosen screw to


7
Connect the Cable Assembly
4

8
Install Interior Escutcheon
5
See comment about
reset buon on page
26, “Reseng Lock to
Factory Default.”

9
Tesng Operaon
6

10
1. Determine mounng locaon 1-1/2”
3-1/2”
DoorSense
TM
Cover
DoorSense
TM


Tape

Screws
Installing DoorSenseTM
Surface Mount Opon
7a

11
2. Aach mounng tape then screw into frame
Installing DoorSenseTM
Surface Mount Opon
7a
3. Complete the DoorSense™ setup in the Yale Access app
Lock Sengs aer compleng step 12.

12
1. Remove magnet from housing and place DoorSenseTM Cap
onto the magnet
DoorSense
TM

DoorSense
TM
Cap
Installing DoorSenseTM
Flush Mount Opon
7b

13
2. Drill hole and Insert DoorSenseTM
3-1/2”
5/8” Diameter
1/2” Deep
3. Complete the DoorSense™ setup in the Yale Access app
Lock Sengs aer compleng step 12.
Installing DoorSenseTM
Flush Mount Opon
7b

14
!
Bolt must be in retracted


Install Baeries
8

15

must be performed upon




step has been successfully

“Enter a 4 to 8 digit
PIN Code followed by
the gear key.”
“Registered.”
Press
Press
“Register Master PIN
Code. Press the gear
key to connue.”
Creang Master PIN Code
9

16
Handing the Lock
Acvate the Lock
OR
“Handing Lock”
“Handing Lock
Complete”
10

17
Register The Module
11
Follow steps below to enter the



 


  
  
 



the keypad, it may be due to any of


 
 
Press
Press
“Enter Master PIN
Code. Press the gear
key to connue.”
“Press 7 and then the
gear key.”
“Press the red arrow to
exit the menu.”

18
Download or go the Yale Access App
to Complete Installaon
Set Up an Emtek Lock in the Yale Access App
Set Up a Yale/August Connect Wi-Fi Bridge
12
SET UP A DEVICE
SET UP A DEVICE
CAN’T SCAN
THE CODE
CAN’T SCAN
THE CODE
CAN’T FIND THE
SERIAL NUMBER
ENTER SERIAL
NUMBER (FOUND
ON CONNECT
BRIDGE) OR
CAN’T FIND THE
SERIAL NUMBER
EMTEK
YALE
RADIO MODULE
ACCESSORY
MD-01
CONNECT
WI-FI
BRIDGE
QR Codes
Coming Soon
QR Codes
Coming Soon

19
Install Cover


13

20
1. Touch screen with back of hand or palm to acvate.
2. Enter 4-8 digit master PIN Code* followed by key.
Lock Response: “Menu mode, enter number, press key to connue.”
3. Enter digit corresponding to the funcon to be performed followed by the key.
Follow the voice commands.
*The Master PIN Code must be registered prior to any other programming of the lock.
Feature Programming Through Menu Mode
Using Master PIN Code*