Enable-IT 828W User manual

!
Enable-IT 828W Weatherproof
Professional Grade PoE Extender Unit
Quickstart Guide
All Rights Reserved © 1997 - 2017 Enable-IT™, Inc.

INSTALLING THE 828W WEATHERPROOF POE EXTENDER !
Installation!
!
The Enable-IT 828W – A Dual Output PoE and Gigabit PoE Ethernet Unit has a distance restriction
of 800ft or 240m over 4-pair Category 5e or higher spec rated wiring. Multiple 828W units can be
daisy chained to reach up to 2,000ft or 1,828m. For the 828W daisy chain use additional 828W
units.!
•Total distance limitation of 800ft or 240m from end to end per 828W unit.
•4-pair CAT 5e .24 AWG or better cabling is required for Gigabit throughput.
•Wire pairs used must be straight through, no taps/connection points.
Perform an Out Of The Box Test (OOTBT)
We highly recommend that you perform a quick test to ensure the working order of
your Enable-IT 828W Weatherproof PoE Extender Unit units prior to installing. !
This will also serve to familiarize you with how easy the process should be. Using a
Ethernet patch cord attach any PoE Injector Output to the 828W left side (single port)
sealed jack as shown below in the diagram.
Next use another Ethernet patch cord to connect one of the 828W right side (dual
ports) jack to your PoE device. Power up your PoE Injector. The left side Green Power
LEDs will turn on and all Yellow Link LEDs will flicker for LAN traffic activity. This
confirms basic proper operation of the units.
For a more detailed test and to confirm your LAN Equipment works with the 828W
units, connect your Ethernet LAN to the PoE injector LAN in port and then test LAN
port and test connectivity all the way end to end.
You will need a long flathead screwdriver to carefully remove the Ethernet patch cables
from the deeply recessed ports prior to installing.
All Rights Reserved © 1997 - 2017 Enable-IT™, Inc. Page !of !2 5

Performing the On-Site Installation
After removing the Enable-IT 828W Weatherproof PoE Extender Unit from the box, and
performing the Out Of The Box Testing (OOTBT), all that remains to install the unit on-site is
to mount the unit, attach the LAN device cabling through the open end screw caps, use the
grey sealant around the inserted Ethernet RJ45 LAN cable (inside the screw cap) and
securely tighten the screw caps.
Mounting the Enable-IT 828W Weatherproof PoE Extender Unit Units!
The Enable-IT 828W Weatherproof extended Ethernet solution is designed for quick wall
mounting. Choose a location to mount each of the Enable-IT 828W Weatherproof’s where
the maximum distance does not exceed 400ft or 121m from your PoE injector and or the end
PoE device or next 828W unit - (See diagram below). When wall-mounting the Enable-IT
828W Weatherproof unit it is recommended that you use the appropriate screw anchors for
your mounting surface. If mounting on existing plywood use wood screws; if mounting onto
drywall or sheetrock, use plastic drywall anchors to secure your installation.
TECHNICAL SUPPORT
Enable-IT, Inc.’s Customer Care Team support is available directly to customers and distributors. All
support requests are processed through the online support portal. This allows us to provide
assigned support ticket numbers in order to bring closure to any technical issues.
Online Technical Services
The Enable-IT Support Portal is available 24/7 to open a ticket or check the status of one. Please
use this support website as your first source for help as it contains an on-line knowledge base of
articles, documentation, FAQ's and other problem-solving resources. This web-based support
resource provides the quickest solution to the most common technical support issues.
World Wide Web Site
https://enableit.com/customer-care-support
All Rights Reserved © 1997 - 2017 Enable-IT™, Inc. Page !of !3 5

Returning Products for Warranty Repair
Enable-IT warrants to the original purchaser of the Product ("you" or the "End User") that, for the
limited lifetime period commencing on the date the Product was purchased (the “Warranty Period"),
the Product will be substantially free from defects in materials and workmanship under normal use
and conditions. This warranty does not apply to Products, which are resold as used, repaired or
reconditioned. Electrical or water damage is not covered under this warranty, extended
warranties or Advanced Replacement Program (AREP).
In order to obtain an authorized RMA approval, the End User must complete the required
information online located at http://support.enableit.com. If you have questions or difficulty
completing this information you may contact the Customer Care Team at 888-309-0910 between
the hours of 6:30 a.m. and 4:00 p.m. PT.
Please ship Authorized RMAs to:
RMA Warranty Repair Processing Facility
16027 Brookhurst St, Suite G272
Fountain Valley, CA 92708-1551
Returning Products for Refund
Enable-IT, Inc. offers a generous 45-Day refund on a single Ethernet Extender Kit only, and is
subject to a 15% Restocking Fee. Shipments without a valid or authorized RMA number, or
sent to our corporate Las Vegas address, can be refused and / or billed for additional
shipping.
ENABLE-IT, INC. LIMITED WARRANTY
Enable-IT, Inc. warrants the Enable-IT 828W Weatherproof PoE Extender Unit solely pursuant
to the following terms and conditions.
1.ENABLE-IT PRODUCT WARRANTY.
a. Express Warranty.
Enable-IT warrants to the original purchaser of the Product ("you" or the "End User") that,
forthelimitedlifetimeperiodcommencingonthedatetheProductwaspurchased(the
“WarrantyPeriod"),theProductwillbesubstantiallyfreefromdefectsinmaterialsand
workmanshipundernormaluseandconditions.ThiswarrantydoesnotapplytoProducts,
whichareresoldasused,repairedorreconditioned.
Electrical or water damage are not covered under this warranty, extended warranties
orAdvancedReplacementProgram(AREP).
!
Enable-IT does not make any warranty with respect to any third party product, software or
accessorysuppliedwithorusedinconnectionwiththeProductandsuchthirdparty
products,softwareandaccessories,ifany,areprovided"ASIS."Warrantyclaimsrelatedto
suchthirdpartyproducts,softwareandaccessoriesmustbemadetotheapplicablethird
partymanufacturer.
All Rights Reserved © 1997 - 2017 Enable-IT™, Inc. Page !of !4 5

CONTACT US
Sales and Customer Care:
Toll Free US and Canada 888 309-0910
866 389-8605 Fax
Other International [phone]
[phone] Fax
E Mail [email protected]
[email protected]
RMA Support:
https://support.enableit.com
All Rights Reserved © 1997 - 2017 Enable-IT™, Inc. Page !of !5 5