Enable-IT 865XSC PRO User manual

Enable-IT 865XSC PRO
Gigabit Coax PoE Extender Kit
Quickstart Guide
Professional Grade Networking
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc.

INSTALLING THE 865XSC PRO COAX POE EXTENDER KIT
We highly recommend that you perform a quick out of the box test to ensure the working order of your
Enable-IT 865XSC PRO Gigabit Coax PoE Extender units prior to installing. This will also serve to
familiarize you with how easy the process should be. Follow the steps below to perform the Out Of the
Box Test.
Step 1 - Attach the 60W 56V DC Gigabit PoE Injector and power adapter to the local 865XSC PRO unit and
power up the unit. The Power LEDs will indicate the injector and 865XSC PRO unit is receiving power.
Step 2 - Connect the 865XSC PRO units together using your own RJ6 75 Ohm Coax cable – attach
to the coax cable to the Interlink port on each 865XSC PRO unit as shown by the green line
connecting the units in the diagram above. The 865XC PRO CO unit Green Link LED will blink rapidly
when it is connected to the Extender unit successfully and passing traffic (data).
Step 3 - Next for a more detailed test and to confirm your PoE Equipment works with the 865XSC PRO,
connect your Ethernet LAN to the 865XSC PoE Injector and the remote PoE device/s to
the remote 865XSC PRO LAN port and test connectivity. The Green Interlink Sync LED will pulse
rapidly as it detects traffic.
This confirms basic proper operation of the units.
Performing the On-Site Installation
After removing the Enable-IT 865XSC PRO Gigabit Coax PoE Extender Kit from the box, and
performing the Out Of The Box Testing (OOTBT), all that remains to install the unit on-site is to
mount the unit, build the interconnect wiring, add voice lines if needed, and attach the LAN
device cabling with the provided Ethernet Patch cords.
Building the 865XSC PRO Interlink Wiring
The most important aspect of the installation is the correct wiring of the Interlink cabling.
The 865XSC PRO Interlink port (Coax BNC) carries this 1-pair signaling over 75 Ohm rated
RG6 cabling and is used as the transport for gigabit transport.
For all wiring you will need to crimp a Coax BNC head to each end of the contiguous wire run.
The 865XSC PRO BNC Interlink port carries this 1-pair signaling and power over the coax.
For all wiring you will need to crimp a 75 Ohm BNC Female head to each end of the contiguous
wire run straight through. We recommend using 75 Ohm coaxial cable as it is optimized for high
throughput frequencies isolated from cross-talk noise. Insert the completed BNC ends into the
865XSC PRO BNC Interlink port on each 865XSC PRO unit.
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc. Page of2 4
The Enable-IT 865XSC PRO Gigabit Coax Ethernet Extender Solution has a distance reach of up to
3,000ft (915m) over 75 Ohm rated RG6 cabling between the 860XSC PRO units. You can add an
additional 328ft (100m) onto the end of each 860XSC PRO LAN output ports for a total distance of
3,656ft (1.1km) from device extension to device extension.!
!
Therefore a site survey of the wiring and installation planning are highly recommended.!

Cabling Devices to The Enable-IT 865XSC PRO Extended Ethernet Kit
Attach your remote PoE device to the 865XSC PRO CPE unit LAN ports with Ethernet patch cord
provided. Attach your local LAN to the 865X PoE Injector PoE Injector with Ethernet patch cord
provided. Attach the power adapters to both 865XSC PRO units.
Attach your local Interlink cabling end to the 865XSC PRO CO unit Interlink port – Then do the same
for the remote end and plug into the 865XSC PRO CPE unit Interlink port. The Sync LED’s will flicker
in a sequence talking to each other until they go solid. Your equipment should now be powered up
and functioning. LED indicators will provide visual operational status of the 865XSC PRO units.
Troubleshooting
First examine the backbone wiring pair and make sure you have solid connections. The Interlink Link
LED should blink rapidly, indicating is sees the remote partner. The units sync instantly and have no
delay. If either fail to light up.... Then follow the steps below:
1) Make sure your wiring is straight through end to end coax.
2) Check for a firm connection of the RJ-45 and Coax BNC connections in each 865XSC PRO
unit, and power is applied to the 865XSC PRO CO & CPE units.
3) You can easily isolate any issue by performing an Out Of The Box Test (OOTBT). This test
will confirm the correct working order of your Enable-IT 865XSC PRO Gigabit Coax PoE
Extender Kit. This will point to a possible issue with your long distance Interlink wiring being
affected by possible outside interference.
865XSC PRO Remote unit DIP Switch Settings
•Switch 1: ON - only for 865XSC PRO remote unit
PoE On – Down / On Position - Default
PoE Off – Up / Off Position
•Switch 2: ON - only for 865XSC PRO remote unit 4-Pair output
PoE 2-Pair – Up / Off Position
PoE 4-Pair – Down / On Position - Default
•Switch 3: Not Used
•Switch 4: Not Used
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc. Page of3 4
865XSC PRO CPE
865XSC PRO CO
Coax Interlink Cabling up to 3,000 feet / 914m

TECHNICAL SUPPORT
Online Technical Services
The Enable-IT Support Portal is available 24/7 to open a ticket or check the status of one. Please use
this support website as your first source for help as it contains an on-line knowledge base of articles,
documentation, FAQ's and other problem-solving resources. This web-based support resource
provides the quickest solution to the most common technical support issues.
Returning Products for Warranty Repair
Enable-IT warrants to the original purchaser of this described Product ("you" or the "End User") that,
for the limited lifetime period commencing on the date the Product was purchased (the “Warranty
Period"), the Product will be substantially free from defects in materials and workmanship under
normal use and conditions. Lifetime Warranty details here: https://warranty.enableit.com
This warranty does not apply to Products, which are resold as used, repaired or reconditioned.
Electrical or water damage is not covered under this warranty, extended warranties or
Advanced Replacement Program (AREP).
In order to obtain an authorized RMA approval, the End User must complete the required information
online located at https://support.enableit.com Ifyouhavequestionsordifficultycompletingthis
information you may contact the Customer Care Team at 888-309-0910 between the hours of 7:00
a.m. and 4:00 p.m. Pacific Time(PST).
Returning Products for Refund
Enable-IT, Inc. offers a generous 45-Day refund on a single Ethernet Extender Kit only, and is
subject to a 20% Restocking Fee. Shipments without a valid or authorized RMA number, or
sent to our corporate Las Vegas address, can be refused and / or billed for additional shipping.
CONTACT US
Sales and Customer Care:
Toll Free US and Canada 888 309-0910
Other International [phone]
E Mail [email protected]
[email protected]
RMA Support:
https://support.enableit.com
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc. Page of4 4