Enable-IT 865XC PRO User manual

Enable-IT 865XC PRO
Gigabit Coax PoE Extender Kit
Quickstart Guide
Professional Grade Networking
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc.

INSTALLING THE 865XS PRO POE EXTENDER KIT
We highly recommend that you perform a quick out of the box test to ensure the working order of your
Enable-IT 865XS PRO Gigabit PoE Extender units prior to installing. This will also serve to familiarize
you with how easy the process should be. Follow the steps below to perform the Out Of the Box Test.
Step 1 - Attach the 60W 56V DC Gigabit PoE Injector output to the power side LAN port on the single port
865X PRO unit. Power up the PoE Injector. The Power LEDs will indicate the injector and 865X
PRO unit are receiving power.
Step 2 - Connect the 865XS PRO RJ-45 Interlink ports together using one of the Ethernet LAN Patch cords
provided – as shown by the green line connecting the ports in the diagram above.
On both units, the green Link LED will blink rapidly when it sees the partner unit and connects
successfully. The LAN Port LEDs will blink as they see passing traffic (data).
!
Step 3 - Next for a more detailed test and to confirm your PoE Equipment works with the 865XS PRO, connect
your local Ethernet LAN to the 60W 56V DC Gigabit PoE Injector and your remote PoE device/s to the
remote 865XS PRO LAN ports and test connectivity. Green Blink rapidly when it sees the partner unit
indicates working connection – Green No LED indicates it cannot see the partner unit.
LAN/Power side LEDs
Mode – Green LED (LED On = CO unit, LED Off = CPE unit)
Link – Green Blink rapidly when it sees the partner unit – indicates working connection
– Green No LED indicates it cannot see the partner unit.
Power – Green Solid LED indicates the unit is receiving 12V power.!
!
LAN Sync. – Green LED
Off = No device attached or detected.
On = Solid, indicates the presence of local LAN.
LAN Act. – Yellow LED
Blinking = Indicates the presence of local LAN traffic.
The Green Link LEDs will blink rapidly when it sees the partner unit and connects successfully.
This confirms basic proper operation of the units.!
!
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc. Page of2 5
The Enable-IT 865XS PRO Gigabit PoE Extenders have a distance restriction of 3,000ft (915m) over
1-pair of copper wiring from device extension to device extension.!
!
Therefore a site survey of the wiring and installation planning are highly recommended.!
For highest performance use 100Mhz rated for the interlink wiring.

Performing the On-Site Installation"
After removing the Enable-IT 865XS PRO Gigabit PoE Extender Kit from the box, and
performing the Out Of The Box Testing (OOTBT), all that remains to install the unit on-site is to
mount the unit, build the interconnect wiring, add voice lines if needed, and attach the LAN
device cabling with the provided Ethernet Patch cords.
Building the 865XS PRO Interlink Wiring
The most important aspect of the installation is the correct wiring of the Interlink cabling.
For all wiring you will need to crimp a (LAN Standard) RJ-45 Male head to each end of the
contiguous wire run and using the following TIA 568B straight through standard. We recommend
using a category rated 100MHz or better twisted pair cable as it is optimized for high throughput
frequencies isolated from cross-talk noise. Insert the completed RJ-45 ends into the 865XS
PRO Interlink port on each 865XS PRO unit.
Cabling Devices to The Enable-IT 865XS PRO Extended Ethernet Kit
Connect your local Ethernet LAN to the 60W 56V DC Gigabit PoE Injector and your remote PoE
device/s to the remote 865XS PRO LAN ports and test connectivity. Green Blink rapidly when it sees
the partner unit indicates working connection – Green No LED indicates it cannot see the partner unit.
Troubleshooting
First examine the backbone wiring pair and make sure you have solid connections. The Interlink
green Link LED will blink rapidly when it sees the partner unit and connects successfully. If the
Interlink Sync LED Link is off…. Then follow the steps below:
1) Make sure your wiring is straight through and not connected to any Telco punch down
blocks; If so remove from the block and use Telco butt clips to bridge wire.
2) Check for a firm connection of the RJ-45 connections in each 865XS PRO unit, and
power is applied to the 865XS PRO CO & CPE units.
3) You can easily isolate any issue by performing an Out Of The Box Test (OOTBT). This
test will confirm the correct working order of your Enable-IT 865 XS PRO Ethernet
Extender Kit. This will point to a possible issue with your long distance Interlink wiring
being affected by possible outside interference.
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc. Page of3 5
865XS PRO CPE
865X PRO CO
RJ-45 Interlink Cabling up to 3,000 feet / 915m

865XS PRO (4-Port) DIP Switch Settings
•Default is all DIP switches Down = On for 4-port PoE
•Switch 1:
LAN 1 / LAN 2 PoE On – Down / On Position - Default
LAN 1 / LAN 2 PoE Off – Up / Off Position
•Switch 2: 4-Pair output
PoE 4-Pair – Down / On Position - Default
PoE 2-Pair – Up / Off Position (PIN 1,2,3 & 6)
•Switch 3:
LAN 3 PoE On – Down / On Position - Default
LAN 3 PoE Off – Up / Off Position
•Switch 4: Not Used
LAN 4 PoE On – Down / On Position - Default
LAN 4 PoE Off – Up / Off Position
TECHNICAL SUPPORT
Online Technical Services
The Enable-IT Support Portal is available 24/7 to open a ticket or check the status of one. Please use
this support website as your first source for help as it contains an on-line knowledge base of articles,
documentation, FAQ's and other problem-solving resources. This web-based support resource
provides the quickest solution to the most common technical support issues.
Returning Products for Warranty Repair
Enable-IT warrants to the original purchaser of this described Product ("you" or the "End User") that,
for the limited lifetime period commencing on the date the Product was purchased (the “Warranty
Period"), the Product will be substantially free from defects in materials and workmanship under
normal use and conditions. Lifetime Warranty details here: https://warranty.enableit.com
This warranty does not apply to Products, which are resold as used, repaired or reconditioned.
Electrical or water damage is not covered under this warranty, extended warranties or
Advanced Replacement Program (AREP).
In order to obtain an authorized RMA approval, the End User must complete the required information
online located at https://support.enableit.com Ifyouhavequestionsordifficultycompletingthis
information you may contact the Customer Care Team at 888-309-0910 between the hours of 7:00
a.m. and 4:00 p.m. Pacific Time(PST).
Returning Products for Refund
Enable-IT, Inc. offers a generous 45-Day refund on a single Ethernet Extender Kit only, and is
subject to a 20% Restocking Fee. Shipments without a valid or authorized RMA number, or
sent to our corporate Las Vegas address, can be refused and / or billed for additional shipping.
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc. Page of4 5

CONTACT US
Sales and Customer Care:
Toll Free US and Canada 888 309-0910
Other International [phone]
E Mail [email protected]
[email protected]
RMA Support:
https://support.enableit.com
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc. Page of5 5