Endless Summer 235000 User manual

Owners Manual
Manual del Usuario
Model No.
235000
WARNING
FOR YOUR SAFETY
For Outdoor Use Only
(Outside any enclosure)
Solamente Para Uso En Exteriores
(Fuera de cual quier recinto)
WARNING
FOR YOUR SAFETY
Improper installation, adjustment,
alteration, service or maintenance
can cause injury or property
damage. Read the installation,
operation and maintenance
instructions thoroughly before
installing or servicing this equipment.
U.S. Patent Number: 6,6102,031; 6,470,877;
Hong Kong Patent Number: 1108587.1;
All Other Foreign Patents May Apply.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
2
WARNING
FOR YOUR SAFETY
For Outdoor Use Only
(Outside any enclosure)
WARNING
FOR YOUR SAFETY
1. Gas leaks may cause a fire or
explosion which can cause serious
bodily injury or death, or damage to
property.
2. You must follow all leak checking
procedures as outlined in step 12
before operating this unit.
3. Never use an open flame to check for
leaks.
WARNING
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors or liquids in the
vicinity of this or any other appliance.
WARNING
FOR YOUR SAFETY
Improper installation, adjustment,
alteration, service or maintenance
can cause injury or property damage.
Read the installation, operation and
maintenance instructions thoroughly
before installing or servicing this
equipment
WARNING
California Proposition 65:
Chemicals known to the State of
California to cause cancer, birth
defects, or other reproductive harm are
created by the combustion of propane.
WARNING
FOR YOUR SAFETY
• Purchaser assumes all risk in the
assembly and operation of this
unit. Failure to follow this manual’s
WARNINGs and instructions can
result in severe personal injury, death
or property damage.
• Do not use in an explosive
atmosphere. Keep heater away from
areas where flammable liquids,
gasoline, vapors, or explosives are
stored or used.
WARNING
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, immediately call
your gas supplier.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater 3
Table of Contents
SafetyFirst!................................................................4
Assembly Instructions
Components&Hardware.................................................6
GeneralComponents&Features...........................................7
AdditionalRequirements.................................................7
Step 1 AttachLegstoBase ..............................................7
Step 2 AttachPlatformtoLegs............................................8
Step 3 AttachWeightPlatetoBase ........................................8
Step 4 Insert Gas Line Through Platform / Attach Shroud Cover . . . . . . . . . . . . . . . . . . .9
Step 5 Attach Small and Medium Domes to Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Step 6 AttachEnginetoPost ............................................10
Step 7 Attach Engine/Post to Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 8 ConnectGasLinetoEngine .......................................11
Step 9 AttachTopDometoEmitter........................................11
Step 10 SecureGasLine...............................................11
Step 11 Connect Gas Line to Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Step 12 CheckforLeaks...............................................12
Step 13 Replace Engine Access Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Step 14 InstallIgniterBattery............................................13
Operation
BeforeTurningGasSupplyON............................................14
BeforeLighting .......................................................14
Lighting............................................................ 14
Re-Lighting..........................................................15
Shutdown ...........................................................15
OperationChecklist....................................................16
Troubleshooting............................................................17
Maintenance..............................................................18
Storage..................................................................19
Service ..................................................................19
Warranty.................................................................20
Specifications .............................................................21
The use and installation of this product must conform to local codes. In absence of local codes,
use the National Fuel and Gas Code, ANSI Z223.1/NFPA 54, Storage and Handling of Liquefied
Petroleum Gases, ANSI/NFPA 58 or CSA B149.1, Natural Gas and Propane Installation Code.
Save these instructions for future
reference. If you are assembling this
unit for someone else, give this
manual to him or her to
save for future reference.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
4
Safety First!
Read and become familiar with this entire manual, especially the following precautions.
If you are unsure of anything in these instructions, STOP and contact
1.800.762.1142 for assistance.
Caution: This appliance is for outdoor use only (outside any enclosure). Always
make sure there is fresh air ventilation.
• Always maintain at least 36” clearance (top) and 24” clearance (side) from combustible
materials.
• Always place heater on a hard and level surface.
• Do not use if the wind velocity is greater than 10 miles per hour.
• Unit will operate at reduced efficiency below 40ºF (5ºC).
• Keep sprinklers and other water sources away from burner and controls.
• Always use extreme caution when near heater. Alert both children and adults to
the hazards of high temperatures, especially to avoid burns or clothing catching
fire.
• Young children and pets should be carefully supervised when they are in the area
of heater.
• Do not hang clothing or other flammable materials either on or near heater.
• Any guard or other protective device removed for servicing the heater must be
replaced prior to operating the heater.
• Certain materials or items, when stored under heater, will be subjected to radiant heat
and could be seriously damaged.
• Do not alter heater in any manner.
• The pressure regulator and hose assembly supplied with the appliance must be used
and replacements must be those specified by the manufacturer.
• Inspect heater before each use. If a damaged part is detected, do not operate until an
original equipment replacement part has been properly installed. Use of unauthorized
parts will void warranty and create an unsafe condition.
• Do not attempt to use this appliance without a functional factory-supplied gas regulator
in place. If regulator becomes damaged, use only a factory-supplied replacement.
• Prior to operating heater, replace any guards or protective devices removed for
servicing.
• During operation, do not touch burner assembly. The surface of heater’s emitter can
reach temperatures approaching 1600ºF.
• After shutdown, do not touch burner assembly until heater has cooled (approximately
45 minutes after use).
Notice: This product should not be used with any fuel other than liquid propane. Use of
other fuels will detract from heaters performance and will void your warranty.
Caution: Liquid propane (LP) gas is flammable and hazardous if handled
improperly. Become aware of the characteristics before using any LP product.
• LP Characteristics – Flammable, explosive under pressure, heavier than air - settles in
pools in low areas.
Before you do anything else,
read and understand all
precautions in Safety First!
WARNING
FOR YOUR SAFETY
• Purchaser assumes all risk in the
assembly and operation of this
unit. Failure to follow this manual’s
WARNINGs and instructions can
result in severe personal injury,
death or property damage.
• Do not use in an explosive
atmosphere. Keep heater away
from areas where flammable
liquids, gasoline, vapors, or
explosives are stored or used.
Ceiling
Wall
24”
36”

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater 5
• In its natural state, propane has no odor. For your safety, an odorant is added that
smells like rotten cabbage.
• Contact with LP can cause freeze burns to skin.
• This heater is shipped from the factory for LP gas use only.
• Use only Department of Transportation (DOT) approved “20 lb.” LP gas cylinders (same
as those commonly used on gas grills) with Acme / Type 1 / QCC safety valves. These
valves can be quickly identified because they have external and internal threads.
• Never use an LP cylinder with a damaged body, valve, collar, or footring.
• Dented or rusted LP cylinders may be hazardous and should be checked by your LP gas
supplier.
• The cylinder supply system must be arranged for vapor withdrawl.
• The cylinder used must include a collar to protect the cylinder valve.
• When heater is not in use, turn LP cylinder OFF.
• Always perform a leak test on gas connections whenever a cylinder is connected. Never
use a flame to test for leaks. Do not smoke while performing a leak test.
Caution: It is essential to keep the heater’s valve compartment, burners, and
circulating air passages clean.
• Spiders and insects can create a dangerous condition that may damage heater or make
it unsafe. Keep burner area clean of all spiders, webs, or insects.
• Inspect heater before each use.
• Have heater inspected annually and repairs should be made by a qualified service
person.
• Check heater immediately if any of the following conditions exist:
• The smell of gas in conjunction with extreme yellow tipping of burner flames.
• Heater does not reach proper temperature.
Note: At temperatures less than 40ºF, heat output will be reduced.
• Heater’s glow is excessively uneven
• Burner makes popping noises during use.
Note: A slight pop is normal when burner is extinguished.
• Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times.
• Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water.
• Do not paint engine, engine access panel or dome.
FOR YOUR SAFETY:
Beware of Spiders
Spiders or small insects can get into the
burner tube or other openings of your
heater, and spin webs or build nests.
These obstructions can lead to gas
flow problems. It is important to make
frequent inspections of these areas and
clean them when necessary.
Before operating your heater for the first
time, be sure to check for obstructions
that may have occurred during
shipment.
Need a cylinder or gas?
Try Blue Rhino cylinder exchange service. It’s easy,
fast, safe, and available at tens of thousands of
conveniently located retail outlets nationwide. You
can purchase a new full cylinder or exchange your
empty for a precision filled one.
For your nearest Blue Rhino retailer visit www.
bluerhino.com.
“20 lb.” LP Cylinder
Collar
Valve
Body
Foot
18”-19”

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
6
Components Part Name
Large Dome
Medium Dome
Small Dome
Emitter
Valve Housing Assembly
Pilot Assembly
Nozzle
Impulse Ignitor
Valve Housing Cover
Valve
Knob
Pole
Platform Cover
Shroud
Platform
Gas Line/ Regulator Assembly
Leg (3)
Tank Retention Chain
Plug (2)
Base
Weight Plate
Hardware
Picture Qty Description
Used in
Step(s)
A4
Small Screw
1/4”-20 x 10 Stainless
Steel Philips Head Screw
6
B1
Large Screw
1/4”-20 x 20 Nickel
Plated Philips Head Screw
2
C6
Small Bolt
5/32”-32 x 12 Stainless
Steel Hex Head Bolt
5
D12
Large Bolt
1/4”-20 x 20 Nickel
Plated Hex Head Bolt
1 & 2
E
1 Carriage Bolt
3/8”-16 x 95 White Zinc
Plated
3
F12
Small Nut
1/4”-20 Nickel Plated
Hex Nut
1 & 2
G1
Large Nut
3/8”-16 Nickel Plated
Hex Nut
3
H3
Cap Nut
5/26”-18 Stainles Steel
Cap Nut
9
I12
Small Lockwasher
M6 Nickel Plated
Lockwasher
1 & 2
J1
Large Lockwasher
M10 Nickel Plated
Lockwasher
3
K1 Clip 2
L1 Battery 14
M1 Allen Wrench 7
Available Accessories
Ask your retailer or call 1.800.762.1142
Wheels Model # 269922
Cover Model # 251958

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater 7
Assembly Instructions
General Components & Features
Familiarize yourself with all components before proceeding. Refer to page 6 for hardware and components, and page 21 for specifications.
The white ceramic cone in the top of the engine is an important piece. DO NOT REMOVE.
Do NOT attempt assembly unless all components are available. If you believe a component is missing or damaged, contact 1.800.762.1142 for
assistance.
Note: All hardware is mounted on a cardboard pack and numbered to match their assembly step.
Additional Requirements
The following items are not included, but are necessary for the proper assembly of your heater. Do NOT attempt to assemble without proper tools.
A hex (Allen) wrench is necessary and is included in the parts bag.
(1) 7/16” Wrench
(1) 9/16” Wrench
(1) 7/16” Socket Wrench
(1) #2 Phillips Head Screwdriver
(1) Leak Detection Solution (Instructions on how to make solution are included in step 12)
(1) Precision Filled LP Gas Grill Cylinder with Acme Type 1 external threaded valve connection (4-5 gallon size)
Note: You must follow all steps to properly assemble heater.
Step 1 – Attach Legs to Base
Secure legs to base using 6 sets of large bolts (D), small lock washers (I), and small
nuts (F). Finger tighten only.
Do not fully tighten until step 2.
Attach small ‘s’ hook on cylinder restraint chain to left leg.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
8
Step 2 – Attach Platform to Legs
Line up hole in clip (K) with small threaded hole on bottom of platform.
Attach clip loosely to platform with large screw (B).
Note: do not tighten until step 10.
Using 7/16” wrench, secure platform to legs using 6 sets of large bolts (D), small lock
washers (I), and small nuts (F). Tighten fully.
Fully tighten all nuts and bolts from step 1.
Step 3 – Attach Weight Plate to Base
Lay base assembly on its side.
Place weight plate in base, feet out.
Insert carriage bolt (E) through center holes of base and plate.
Using 9/16” wrench, secure plate to base using a large lock washer (J) and large
nut (G).
Place base assembly upright.
TIP:
To tighten use a 7/16” wrench on bolt and a 7/16” socket wrench on nut.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater 9
Step 4 – Insert Gas Line through Platform/Attach Shroud Cover
Insert gas line up through large hole in platform from underneath between center and
left leg as shown in illustration.
Slide shroud cover over gas line, then over platform/leg assembly until bottom of
shroud rests on base.
Step 5 – Attach Small & Medium Dome to Engine
Set engine assembly on its top as shown at left.
Carefully slide medium sized dome over engine assembly, and line up slots in dome
with fins on dome brackets.
Line up holes in dome with threaded holes in bracket and 3 small bolts (C) into each
hole, finger tightening at first.
After three bolts are in place, tighten with 7/16” wrench.
Repeat process for small dome.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
10
Step 7 – Attach Engine/Post to Platform
Insert platform cover over gas line and set on top of shroud cover.
Insert end of post without holes over gas line, being careful not to bend gas line.
Slide post through cover and into collar of platform so post rests completely on
platform.
Align the control panel with either the right or left leg attached to base.
Slide platform cover up to expose setscrews in platform and tighten bottom three
setscrews with hex (allen) wrench (M) supplied.
Make sure post is perpendicular to base.
Use top three setscrews to adjust post’s angle as necessary.
Tighten all six setscrews and slide cover back down.
Note: post must be perpendicular to base. Failure to do so will adversely affect burner
performance.
Step 6 – Attach Engine to Post
Lay engine assembly on its side, using shipping carton for support.
Remove and save control knob.
Remove and save engine access panel by unscrewing black thumbscrew from bottom
of access door.
Disconnect wire from igniter by gently pulling wire from back of box.
Align 4 holes in top of post with 4 holes in bottom of engine.
Note: one hole is at a different level than the rest. Make sure that all 4 holes line up
properly.
Insert 4 small screws (A) enough to hold engine in place. They will be fully tightened at
the end of step 8.
Note: do not replace engine access panel until step 13.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater 11
Step 8 – Connect Gas Line to Engine
Attach gas line to control valve:
Pull collar of gas line back. (small arrow)
Insert gas line over control valve. (large arrow)
Release collar and it should lock in place. (Tip – push gas line up from bottom of post to
make a good seating before releasing the collar.)
Gently tug on line to test for proper connection. If gas line moves you are not properly
connected. Do not proceed until you have a proper connection.
Fully tighten the (4) screws from step 6.
Step 9 – Attach Top Dome to Emitter
Gently lay heater on its side using one styrofoam insert to prop
up top half.
Align holes in dome with threaded studs in emitter brackets.
Secure dome to emitter using 3 cap nuts (H). Tighten using 13 mm wrench.
Stand heater upright.
NOTE:
The white ceramic cone in the top of the engine is
an important piece. DO NOT REMOVE.
Step 10 – Secure Gas Line
Make sure angled side of gas clip pokes up through large hole in platform.
Tighten screw until gas line is held securely in place.
Stand heater upright.
Section View
Gas Line
Clip Gas Line
Bottom View

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
12
Caution
Before you attempt to use a propane
cylinder, understand all cylinder
and propane related precautions in
Section #1 - “Safety First.”
Caution
Your Endless Summer Heater
has been checked at all factory
connections for leaks. Recheck
all connections, as movement in
shipping can loosen connections.
Check for leaks even if your unit was
assembled for you at the store.
Step 11 – Connect Gas Line to Cylinder
The pressure regulator and hose assembly supplied with the appliance must be used and
replacements must be those specified by the manufacturer.
• Slide full propane cylinder onto heater base.
• Attach gas line to cylinder by turning black plastic knob clockwise over cylinder valve
until tight.
Note: be careful not to kink flexible hose of gas line.
• Secure cylinder in place by attaching loose end of cylinder restraint chain to hole in
right leg.
Step 12 – Check for Leaks
• Make 2-3 oz. Of leak check solution by mixing one part liquid dishwashing soap and
three parts water.
• Turn cylinder valve on.
• Check gas line / control valve for leaks:
• Spoon several drops of solution onto gas line and control valve connection.
• Inspect the solution at the connection to look for bubbles.
• If no bubbles appear, then the connection is secure.
• If bubbles appear, there is a leak -
• Turn cylinder valve off.
• Loosen screw on clip.
• Release gas line fitting from control valve and re-attach making sure connection is
secure (see step 8).
• Retighten clip.
• If you continue to see bubbles after several attempts, contact
1.800.762.1142 For assistance.
Check Gas Line / Cylinder valve for leaks:
• Turn cylinder valve on.
• Spoon several drops of solution onto gas line and cylinder valve connection.
• Inspect the solution at the connection to look for bubbles.
• If no bubbles appear, then the connection is secure.
• If bubbles appear, there is a leak:
• Turn cylinder valve off.
• Release gas line fitting from cylinder valve and re-attach making sure connection is
secure (see step 11).
• If you continue to see bubbles after several attempts, contact
1.800.762.1142 For assistance.
• Turn cylinder valve off.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater 13
Step 13 – Replace Engine Access Panel
Slide igniter wire onto igniter post.
Slide tab at top of access panel into slot in emitter bottom.
Rotate panel down until holes line up at bottom.
Secure access panel in place with thumbscrew.
Replace control knob.
Step 14 – Install Igniter Battery
Remove battery cover cap by turning cap counterclockwise.
Install AA battery (L). Negative end of battery goes in first.
Replace battery cover cap by turning cap clockwise.
Note: once you have successfully completed assembly steps 1-14 you are ready to
begin operating your heater.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
14
Operation
Caution: Do NOT attempt to operate heater until you have read and understand all
precautions in section 1 “Safety First.”
Before Turning Gas Supply ON
• Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it
inside a building, garage, or any other enclosed area.
• Make sure surrounding areas are free of combustible materials, gasoline, and other
flammable vapors or liquids.
• Ensure that there is no obstruction to air ventilation.
• Be sure all gas connections are tight and there are no leaks.
• Be sure the access panel is clear of debris.
• Be sure any component removed during assembly or servicing is replaced and
fastened prior to starting.
Before Lighting
• Heater should be thoroughly inspected before each use, and by a qualified service
person at least annually.
• If relighting a hot heater, always wait at least 5 minutes.
• Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear.
Suspected areas should be leak tested. If the hose leaks, it must be replaced prior to
operation. Only use the replacement hose assembly specified by manufacturer.
Lighting
Note: This heater is equipped with a Pilot Light that allows for safer startups and
shutdowns. Pilot must be lit before Main Burner can be started.
• Turn Cylinder Valve OFF.
• Push Control Knob IN and turn to OFF.
• Wait 5 minutes for any gas to clear.
• Turn Cylinder Valve ON.
• Open Viewing Hole by sliding cover to either side.
• Push Control Knob IN and rotate to Pilot position.
• Note - For initial start or after any cylinder change, hold Control Knob IN for 2 minutes
to purge air from gas lines before proceeding.
• Push Igniter button once. Pilot Light flame will appear and be visible through Viewing
Hole.
• Release Control Knob after 30 seconds. Pilot Light will remain lit.
If not, return to step 1.
• Turn Control Knob to ON. Main Burner will light immediately. Flame is visible through
Viewing Hole. If not, return to step 1.
WARNING
FOR YOUR SAFETY
• Do NOT attempt to operate heater
until you have read and understand
all precautions in Section 1 “Safety
First.” Failure to do so can result
in serious personal injury, death, or
property damage.
• If at any time you are unable to
light burner and smell gas, wait 5
minutes to allow gas to dissipate
before attempting to light heater.
• Do NOT touch emitter or dome or
move heater for at least 45 minutes
after use.
OFF
OFF
LOW
LOW
Pilot
Pilot
(Push in)
HIGH
HIGH
Pilot
Pilot
(Push in)
HIGH
HIGH
LOW
LOW
OFF
OFF
View Hole

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater 15
WARNING
FOR YOUR SAFETY
Be careful when attempting to
manually ignite this heater. Holding
in the control know for more than 10
seconds before igniting the gas will
cause a ball of flame upon ignition.
• If for some reason your ignitor fails to deliver a spark, your heater can be started by
inserting a lit match through the pilot view hole while pushing the control knob in
while in the PILOT position.
If you experience any ignition problem consult “Troubleshooting” on
page 17.
Caution: Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor
from the burning of oils used in manufacturing will appear. Both smoke and odor
will dissipate after approximately 30 minutes. The heater should NOT produce thick
black smoke.
Note: The burner may be noisy when initially turned on. To eliminate excessive noise from
the burner, turn the Control Knob to the Pilot position. Then, turn the knob to the level of
heat desired.
When heater is ON:
Emitter screen will become bright red due to intense heat. The color is more visible at
night.
Burner will display tongues of blue and yellow flame. These flames should not be
yellow or produce thick black smoke, indicating an obstruction of airflow through the
burners. The flame should be blue with straight yellow tops.
If excessive yellow flame is detected, turn off heater and consult “Troubleshooting” on
page 17.
Re-lighting
Note: For your safety, Control Knob cannot be turned OFF without first depressing Control
Knob in PILOT position and then rotating it to OFF.
Turn Control Knob to OFF.
Wait at least 5 minutes, to let gas dissipate, before attempting to relight Pilot.
Repeat the “Lighting” steps on prior page.
Shut Down
Turn Control Knob clockwise to Pilot. (Normally, burner will make a slight popping sound
when extinguished.) Burner will extinguish but Pilot will remain ON.
To extinguish Pilot, depress Control Knob and continue to turn it clockwise to OFF.
Turn Cylinder Valve clockwise to OFF and disconnect Regulator when heater is not in
use.
Note: After use, some discoloration of the emitter screen is normal.
WARNING
FOR YOUR SAFETY
Heater will be hot after use. Handle
with extreme care.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
16
Operation Checklist
For a safe and pleasurable heating experience, perform this check before each use.
Before Operating
qI am familiar with entire owner’s manual and understand all precautions noted in
“Safety First”.
qAll components are properly assembled, intact and operable.
qNo alterations have been made.
qAll gas connections are secure and do not leak.
qWind velocity is below 10 mph.
qOutdoor temperature is greater than 40 degrees F.
qHeater is outdoors (outside any enclosure).
qThere is adequate fresh air ventilation.
qHeater is away from gasoline or other flammable liquids or vapors.
qHeater is away from windows, air intake openings, sprinklers and other water sources.
qHeater is at least 36” clearance (top) and 24” clearance (side) combustible materials.
qHeater is on a hard and level surface.
qThere are no signs of spider or insect nests.
qAll burner passages are clear.
qAll air circulation passages are clear.
qChildren, pets, clothing, flammable materials and items that can be damaged from
radiant heat are away from the heater.
qChildren and adults in the area have been alerted to the high temperature hazards:
especially burns and clothing fires.
qChildren and adults in the area have been warned not to touch heater near engine
during operation and until unit has cooled.
After Operation
qGas control is in OFF position.
qGas tank valve is OFF
qDisconnect Gas line.
qHeater is upright in a secure location.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater 17
Troubleshooting
If the problem is: And this condition exists: Then do this
Pilot won’t light
Note: Heater operates at reduced efficiency below 40ºF
(5ºC).
Tank valve is closed
Blockage in orifice or pilot tube
Air in gas line
Low gas pressure with tank valve fully open
Igniter fails
Open valve
Clean or replace orifice or pilot tube
Open gas line and bleed it (pressing control
knob in) for not more than 1 - 2 minutes or
until you smell gas
Turn tank valve OFF and replace tank
Use match to light pilot; obtain new igniter
and replace
Pilot won’t stay lit Dirt built up around pilot
Connection between gas valve and pilot
assembly is loose
Thermocouple is not operating correctly
Clean dirt from around pilot
Tighten connection and perform leak check
Replace thermocouple
Burner won’t light Gas pressure is low
Blockage in orifice
Control knob is not in ON position
Turn tank valve OFF and replace tank
Clear blockage
Turn control knob to ON
Burner flame is low Gas pressure is low
Outdoor temperature is less than 40ºF and
tank is less than 1/4 full
Supply hose is bent or kinked
Control knob fully ON
Turn tank valve OFF and replace tan
Use a full tank
Straighten hose
Check burner and orifices for blockage
Emitter glows uneven
Note: Bottom 1” of emitter normally does
NOT glow.
Gas pressure is low
Base is not on a level surface
Heater is level
Turn tank valvue OFF and replace tank
Place heater on a level surface
Clean burner
Carbon build-up Dirt or film on reflector and emitter Clean reflector and emitter
Thick black smoke Blockage in burner Remove blockage and clean burner inside and
outside

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
18
Maintenance
To enjoy years of outstanding performance from your heater, make sure you perform the
following maintenance activities on a regular basis:
Keep exterior surfaces clean.
Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents.
While cleaning your unit, be sure to keep the area around the burner and pilot
assembly dry at all times. Do not submerge the control valve assembly. If the gas
control is submerged in water, do NOT use it. It must be replaced.
Air flow must be unobstructed. Keep controls, burner, and circulating air passageways
clean. Signs of possible blockage include:
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
Heater glow is excessively uneven.
Heater makes popping noises.
Spiders and insects can nest in burner or orifices. This dangerous condition can
damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty
pipe cleaner. Compressed air may help clear away smaller particles.
Carbon deposits may create a fire hazard. Clean dome and emitter with warm soapy
water if any carbon deposits develop.
Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly
than normal. Frequently check for corroded areas and repair them promptly.
WARNING
FOR YOUR SAFETY
• Do NOT touch or move heater for at
least 45 minutes after use.
• Dome is hot to the touch.
• Allow dome to cool before
touching.
TIP:
Use high-quality automobile wax to help maintain the appearance of your heater.
Apply to exterior surfaces from the pole down. Do not apply to emitter screen or
domes.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater 19
Storage
Between uses:
Turn Control Knob OFF.
Disconnect LP source.
Store heater upright in an area sheltered from direct contact with inclement weather
(such as rain, sleet, hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces and to help prevent build up in air
passages.
Note: Wait until heater is cool before covering.
During periods of extended inactivity or when transporting:
Turn Control Knob OFF.
Disconnect LP source and move to a secure, well-ventilated location outdoors.
Store heater upright in an area sheltered from direct contact with inclement weather
(such as rain, sleet, hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces and to help prevent build up in air
passages.
Never leave LP cannister exposed to direct sunlight or excessive heat.
Note: Wait until heater is cool before covering.
Service
To learn how to service and procure parts for worn out, defective or damaged components
contact 1.800.762.1142 for assistance or e-mail [email protected].
Please supply model number and serial ID number for best service support. These
numbers can be found on a label on the rear of the Valve Housing.
Caution: Use only original equipment replacement parts. Use of unauthorized parts
or modification of parts will void warranty and create an unsafe condition.
Caution: Always allow heater to cool before attempting service.

Contact 1.800.762.1142 for assistance.
Do not return to place of purchase.
®
Owner’s manual: model 235000 outdoor patio heater
20
Limited Warranty
Blue Rhino Global Sourcing, LLC (“Vendor”) warrants to the original retail purchaser of this product, and to no other person, that if
this product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of two (2)
years from the date of purchase, all parts in such product shall be free from defects in material and workmanship. Vendor may
require reasonable proof of your date of purchase. Therefore, you should retain your sales slip or invoice. This Limited Warranty
shall be limited to the repair or replacement of parts, which prove defective under normal use and service and which Vendor shall
determine in its reasonable discretion upon examination to be defective. Before returning any parts, you should contact Vendor’s
Customer Service Department using the contact information listed below. If Vendor confirms, after examination, a defect covered by
this Limited Warranty in any returned part, and if Vendor approves the claim, Vendor will replace such defective part without charge.
If you return defective parts, transportation charges must be prepaid by you. Vendor will return replacement parts to the original
retail purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication,
improper installation or improper maintenance or service by you or any third party, or failure to perform normal and routine
maintenance on the product as set out in this owner’s manual. In addition, the Limited Warranty does not cover damage to the
finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase.
This Limited Warranty is in lieu of all other express warranties. Vendor disclaims all warranties for products that are purchased
from sellers other than authorized retailers or distributors, including the warranty of merchantability or the warranty of fitness for a
particular purpose. VENDOR ALSO DISCLAIMS AND ANY ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. VENDOR SHALL NO LIABILITY TO PURCHASER OR
ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Vendor further disclaims any
implied or express warranty of, and assumes no responsibility for, defects in workmanship caused by third parties.
This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she
lives. Some jurisdictions do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on
how long a warranty lasts, so the above exclusion and limitations may not apply to everyone.
Vendor does not authorize any person or company to assume for it any other obligation or liability in connection with the sale,
installation, use, removal, return, or replacement of its equipment, and no such representations are binding on Vendor.
Blue Rhino Global Sourcing, LLC
Winston-Salem, North Carolina 27104 USA
[phone]
[email protected]