Endon Kiera User manual

Kiera Flush Light Fitting
INSTRUCTION MANUAL
Safety Warnings
• Thisproductisonlysuitableforconnectiontoa240V~50HzsupplyinaccordancewithcurrentIEEwiring
regulations.Itshouldbeinstalledinaccordancewithlocalbuildingregulationsandisfordomesticceilinguse
only.Itisarenotsuitableforabathroomlocation.
• Beforeinstallingyourlightttingalwaysswitchoffthemainssupplyandremovetheappropriatefuseor
switchofftheappropriatecircuitbreakerbeforecommencinginstallation.
• ThisisaClassII,DoubleInsulatedproduct ThisFittingdoesnotrequireanEarth,andLiveorNeutral
must notbeconnectedtoEarth.Theterminalblocksaresuppliedaccordingtorequirementsofthetting.
• Nevertbulbsofahigherwattagethanthosespeciedonthelabel,asthesemaycauseoverheatingand
damagethetting.
• Thisproductcontainsdelicateparts–becarefulduringhandlingandmaintenancetoavoidbreakage.
• Ifyouareinanydoubtaboutyourcompetencepleaseconsultaqualiedelectrician.
• Ifanymodicationismadeitwillinvalidatethewarrantyandmayrendertheproductunsafe.
Assembly/ User Instructions
Before you start
Pleasereadtheseinstructionscarefullybeforettingandretainforreference.Checkthepackagingandmake
surethatyouhavealltherequiredparts.Followeachassemblystepinordertopreventincorrectassembly.
Ensurethattheproductisfullyassembledasillustratedbeforeuse.
The Light pack contains:
Lighttting.
Terminalconnectionblock(s).
Fixingpack.
Decorativebeads(asperdiagram)
The following tools may be required:
Selectionofcrossandatheadscrewdrivers.
Electricdrillandassorteddrillbits.
Wirestrippers.
Electricalinsulationtape.
These assembly diagrams are intended as a guide – if in doubt consult a qualied electrician.
Care Information
Allow10minutestocoolbeforereplacing,adjustingorcleaning.
Cleanwithadryclothonly.Donotuseliquidorabrasivecleanersonthisproduct.
1. Decideonthepositionofthelighttting,orremoveexistinglighttting.Notethepositionoftheelectrical
connections.Ensurethereisasolidmountingsurface,preferablyawoodenjoistorjoistbridgetosupport
theweightofthelighttting.
2. Fitthebulbs(1),beingcarefulnottotouchthemwithyourbarehands-useaclothorgloves.NOTE: Never
t bulbs of a higher wattage than those specied on the label (as these may cause overheating and
damage the tting).
3. Fitthecrystals(A&B)asperthediagram,byhookingthemintotheframe.
4. Placethedecorativerim(2)overthettingsothatitcoversthecrystalhooks.
5. Removethetwosidescrews(6)andretainforre-use.Usethexingbracket(3)asatemplatetomarkthe
screwholes.Makethescrewholesandsecuretotheceilingwithappropriatescrewxings(4).
6. Supportyourttingandconnectthehousewiringtotheterminalblock(5)–seeexpandedwiringdetails.
NOTE: This is a Class II tting and must NOT be earthed.Anylooseterminalblocks–notsecuredto
ceilingcup–shouldalwaysbecoveredwith2layersofgoodqualityinsulationtape.
7. Securetheceilingcupoverthebracketbyusingthescrews(6)removedinPoint5.
8. Turnonthepowerandtest.
EndonLighting,LS90SE 67019-Kiera-F20160630

Assembly/ User Instructions Continued
5.Expandedwiringdiagram
EndonLighting,LS90SE 67019-Kiera-F20160630
LN
LN
A:80PCS
A:33PCS
B:1PC
1
2
3
4
56