Endress+Hauser Proline 800 Technical specifications

Products Solutions Services
Brief Operating Instructions
Proline 800
with electromagnetic sensor
Cellular radio (Type: DA800C-CRM02.01)
These instructions are Brief Operating Instructions; they are
not a substitute for the Operating Instructions pertaining to
the device.
Brief Operating Instructions part 2 of 2: Transmitter
Contain information about the transmitter.
Brief Operating Instructions part 1 of 2: Sensor →  3
KA01495D/06/EN/02.22-00
71552846
2022-01-15

Proline 800 Cellular radio
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555

Proline 800 Cellular radio Brief Operating Instructions for flowmeter
Endress+Hauser 3
Brief Operating Instructions for flowmeter
The device consists of a transmitter and a sensor.
The process of commissioning these two components is described in two separate manuals
that together form the Brief Operating Instructions for the flowmeter:
• Brief Operating Instructions Part 1: Sensor
• Brief Operating Instructions Part 2: Transmitter
Please refer to both parts of the Brief Operating Instructions when commissioning the device,
as the contents of the manuals complement one another:
Brief Operating Instructions Part 1: Sensor
The Sensor Brief Operating Instructions are aimed at specialists with responsibility for
installing the measuring device.
• Incoming acceptance and product identification
• Storage and transport
• Installation
Brief Operating Instructions Part 2: Transmitter
The Transmitter Brief Operating Instructions are aimed at specialists with responsibility for
commissioning, configuring and parameterizing the measuring device (until the first
measured value).
• Product description
• Installation
• Electrical connection
• Operation options
• System integration
• Commissioning
• Diagnostic information
Additional device documentation
These Brief Operating Instructions are Brief Operating Instructions Part 2:
Transmitter.
The "Brief Operating Instructions Part 1: Sensor" are available via:
• Internet: www.endress.com/deviceviewer
• Smart phone/tablet: Endress+Hauser Operations App
Detailed information about the device can be found in the Operating Instructions and the
other documentation:
• Internet: www.endress.com/deviceviewer
• Smart phone/tablet: Endress+Hauser Operations App

Table of contents Proline 800 Cellular radio
4 Endress+Hauser
Table of contents
1 About this document .............................................................. 5
1.1 Symbols used ......................................................................... 5
2 Safety instructions ................................................................ 7
2.1 Requirements for the personnel ............................................................ 7
2.2 Intended use .......................................................................... 7
2.3 Workplace safety ...................................................................... 8
2.4 Operational safety ......................................................................8
2.5 Product safety ......................................................................... 8
2.6 IT security ............................................................................ 9
2.7 Device-specific IT security ................................................................ 9
3 Product description ............................................................... 9
4 Mounting ......................................................................... 9
4.1 Mounting the measuring device ............................................................9
4.2 Transmitter post-installation check ........................................................ 19
5 Electrical connection ............................................................ 20
5.1 Electrical safety .......................................................................20
5.2 Connecting requirements ............................................................... 20
5.3 Connecting the measuring device ......................................................... 22
5.4 Power supply via battery packs, Proline 800 - Advanced ........................................ 26
5.5 Connect the cellular antenna ............................................................. 29
5.6 Connecting the pressure sensor, Proline 800 - Advanced ........................................ 30
5.7 Power supply via the external battery pack, Proline 800 - Advanced ................................ 31
5.8 Ensuring potential equalization ........................................................... 32
5.9 Ensuring potential equalization ........................................................... 35
5.10 Post-connection check ..................................................................38
6 Operation options ............................................................... 39
6.1 Overview of operation options ............................................................ 39
6.2 Access to the operating menu via the SmartBlue app ........................................... 39
7 System integration .............................................................. 40
8 Commissioning .................................................................. 40
8.1 Function check ....................................................................... 40
8.2 Preparatory steps ..................................................................... 40
8.3 Configuring the measuring device ......................................................... 41
8.4 Protecting settings from unauthorized access ................................................. 41
9 Diagnostic information .......................................................... 43
9.1 Diagnostic message .................................................................... 43

Proline 800 Cellular radio About this document
Endress+Hauser 5
1 About this document
1.1 Symbols used
1.1.1 Safety symbols
DANGER
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.1.2 Electrical symbols
Symbol Meaning Symbol Meaning
Direct current Alternating current
Direct current and alternating current Ground connection
A grounded terminal which, as far as
the operator is concerned, is grounded
via a grounding system.
Symbol Meaning
Potential equalization connection (PE: protective earth)
Ground terminals that must be connected to ground prior to establishing any other connections.
The ground terminals are located on the interior and exterior of the device:
• Interior ground terminal: potential equalization is connected to the supply network.
• Exterior ground terminal: device is connected to the plant grounding system.
1.1.3 Communication-specific symbols
Symbol Meaning Symbol Meaning
Bluetooth
Wireless data transmission between
devices over a short distance.
Cellular radio
Bidirectional data exchange via cellular
network.

About this document Proline 800 Cellular radio
6 Endress+Hauser
1.1.4 Tool symbols
Symbol Meaning Symbol Meaning
Torx screwdriver Flat-blade screwdriver
Phillips head screwdriver Allen key
Open-ended wrench
1.1.5 Symbols for certain types of information
Symbol Meaning Symbol Meaning
Permitted
Procedures, processes or actions that
are permitted.
Preferred
Procedures, processes or actions that
are preferred.
Forbidden
Procedures, processes or actions that
are forbidden.
Tip
Indicates additional information.
Reference to documentation
A
Reference to page
Reference to graphic
1.
,
2.
,
3.
… Series of steps
Result of a step Visual inspection
1.1.6 Symbols in graphics
Symbol Meaning Symbol Meaning
1, 2, 3,... Item numbers
1.
,
2.
,
3.
… Series of steps
A, B, C, ... Views A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
Flow direction

Proline 800 Cellular radio Safety instructions
Endress+Hauser 7
2 Safety instructions
2.1 Requirements for the personnel
The personnel must fulfill the following requirements for its tasks:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Are authorized by the plant owner/operator.
‣Are familiar with federal/national regulations.
‣Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the application).
‣Follow instructions and comply with basic conditions.
2.2 Intended use
Application and media
The measuring device described in this manual is intended only for the flow measurement of
liquids with a minimum conductivity of 20 µS/cm.
Measuring devices for use in applications where there is an increased risk due to process
pressure are labeled accordingly on the nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣Keep within the specified pressure and temperature range.
‣Only use the measuring device in full compliance with the data on the nameplate and the
general conditions listed in the Operating Instructions and supplementary documentation.
‣Based on the nameplate, check whether the ordered device is permitted for the intended
use in the hazardous area (e.g. explosion protection, pressure vessel safety).
‣Use the measuring device only for media to which the process-wetted materials are
sufficiently resistant.
‣If the ambient temperature of the measuring device is outside the atmospheric
temperature, it is absolutely essential to comply with the relevant basic conditions as
specified in the device documentation.
‣Protect the measuring device permanently against corrosion from environmental
influences.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage caused
by improper or non-designated use.
LWARNING
Danger of breakage due to corrosive or abrasive fluids and ambient conditions!
‣Verify the compatibility of the process fluid with the sensor material.
‣Ensure the resistance of all fluid-wetted materials in the process.
‣Keep within the specified pressure and temperature range.

Safety instructions Proline 800 Cellular radio
8 Endress+Hauser
NOTICE
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in
verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.
Residual risks
LWARNING
If the temperature of the media or electronics unit is high or low, this may cause the
surfaces of the device to become hot or cold. This poses a risk of burns or frostbite!
‣In the case of hot or cold medium temperatures, install appropriate protection against
contact.
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to national regulations.
For welding work on the piping:
‣Do not ground the welding unit via the measuring device.
If working on and with the device with wet hands:
‣Due to the increased risk of electric shock, wear suitable gloves.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which it
is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EU
directives listed in the device-specific EU Declaration of Conformity. Endress+Hauser confirms
this by affixing the CE mark to the device.
Furthermore, the device meets the legal requirements of the applicable UK regulations
(Statutory Instruments). These are listed in the UKCA Declaration of Conformity along with
the designated standards.
By selecting the order option for UKCA marking, Endress+Hauser confirms a successful
evaluation and testing of the device by affixing the UKCA mark.

Proline 800 Cellular radio Product description
Endress+Hauser 9
Contact address Endress+Hauser UK:
Endress+Hauser Ltd.
Floats Road
Manchester M23 9NF
United Kingdom
www.uk.endress.com
2.6 IT security
Our warranty is valid only if the device is installed and used as described in the Operating
Instructions. The device is equipped with security mechanisms to protect it against any
inadvertent changes to the settings.
IT security measures, which provide additional protection for the device and associated data
transfer, must be implemented by the operators themselves in line with their security
standards.
2.7 Device-specific IT security
The device offers a range of specific functions to support protective measures on the operator's
side. These functions can be configured by the user and guarantee greater in-operation safety
if used correctly.
For detailed information on device-specific IT security, see the Operating Instructions for
the device.
3 Product description
Proline Promag 800 - Advanced
Two device versions are available:
• Compact version – transmitter and sensor form a mechanical unit.
• Remote version - transmitter and sensor are mounted in separate locations.
For detailed information on the product description, see the Operating Instructions for
the device →  3
4 Mounting
For detailed information about mounting the sensor, see the Sensor Brief Operating
Instructions →  3
4.1 Mounting the measuring device
4.1.1 Screw tightening torques
For detailed information on the screw tightening torques, see the "Mounting the sensor"
section of the Brief Operating Instructions

Mounting Proline 800 Cellular radio
10 Endress+Hauser
4.1.2 Mounting the transmitter of the remote version, Proline 800 - Advanced
LCAUTION
Ambient temperature too high!
Danger of electronics overheating and housing deformation.
‣Do not exceed the permitted maximum ambient temperature .
‣If operating outdoors: Avoid direct sunlight and exposure to weathering, particularly in
warm climatic regions.
LCAUTION
Excessive force can damage the housing!
‣Avoid excessive mechanical stress.
The transmitter of the remote version can be mounted in the following ways:
• Wall mounting
• Pipe mounting
Wall mounting Proline 800 - Advanced
149 (5.85)
210.5 (8.29)
=
5.8 (0.23)
17 (0.67) =
14 (0.55)
5.8 (0.23)
A0020523
 1 Engineering unit mm (in)

Proline 800 Cellular radio Mounting
Endress+Hauser 11
Post mounting Proline 800 - Advanced
LWARNING
Excessive tightening torque applied to the fixing screws!
Risk of damaging the plastic transmitter.
‣Tighten the fixing screws as per the tightening torque: 2 Nm (1.5 lbf ft)
ø20…70
( 0.79…2.75)ø
~102 (~ 4.0)
4 x SW 10
3 x TX 25
A0029051
 2 Engineering unit mm (in)
4.1.3 Turning the transmitter housing, Proline 800 - Advanced
To provide easier access to the connection compartment or display module, the transmitter
housing can be turned.

Mounting Proline 800 Cellular radio
12 Endress+Hauser
1.
2.
T20
A0044272
1. Loosen the fixing screws of the housing cover (when reassembling, pay attention to the
tightening torque →  15).
2. Open the housing cover.
ON ON
12
3.
4. 5.
A0044274
3. Open the display module.
4. Push the ribbon cable out of the holder.
5. Disconnect the plug.

Proline 800 Cellular radio Mounting
Endress+Hauser 13
6.
7.
A0044273
6. Push the display module down gently at the hinge.
7. Pull the display module out of the holder.
A0043338
8. Disconnect the plug of the electronics module.
T10
1 Nm
(0.7 lbf ft)
A0042853
9. Release the screws on the electronics module.

Mounting Proline 800 Cellular radio
14 Endress+Hauser
A0042843
10. Remove the electronics module.
PUSH TO
REMOVE
TX 20
4 x
11.
PUSH TO
REMOVE
12.
A0044276
11. Loosen the fixing screws of the main electronics module (when reassembling, pay
attention to the tightening torque →  15).
12. Remove the main electronics module.

Proline 800 Cellular radio Mounting
Endress+Hauser 15
14.
15.
13. 4 mm
4 x
A0044277
13. Loosen the fixing screws of the transmitter housing (when reassembling, pay attention
to the tightening torque →  15).
14. Lift the transmitter housing.
15. Turn the housing to the desired position in increments of 90°.
Reassembling the transmitter housing
LWARNING
Excessive tightening torque applied to the fixing screws!
Risk of damaging the plastic transmitter.
‣Tighten the fixing screws as per the tightening torque: 2 Nm (1.5 lbf ft)
Step
→  11
Fixing screw Tightening torques
1 Housing cover 1 Nm (0.7 lbf ft)
9 Electronics module 0.6 Nm (0.4 lbf ft)
11 Main electronics module 1.5 Nm (1.1 lbf ft)
13 Transmitter housing 5.5 Nm (4.1 lbf ft)

Mounting Proline 800 Cellular radio
16 Endress+Hauser
PUSH TO
REMOVE
A0044279
‣Reverse the procedure to reassemble the measuring device.
4.1.4 Mounting the external cellular antenna
If the signal is too weak, mount the external cellular antenna in a separate location.

Proline 800 Cellular radio Mounting
Endress+Hauser 17
2 x TX 15
1
2
3
4
5
A0044318
1 = Antenna (vertical installation, maximum torque for mounting the antenna: 15 Nm)
2 = Antenna (horizontal installation, maximum torque for mounting the antenna: 15 Nm)
3 = Grounding lug with Torx screw and washer
4 = Torx screw with washer
5 = Antenna holder
4.1.5 Mounting the external battery pack
The external battery pack is mounted in the same way as the remote version of the
transmitter →  10.

Mounting Proline 800 Cellular radio
18 Endress+Hauser
4.1.6 Inserting the SIM card
The device is equipped with an Endress+Hauser eSIM. The device automatically
recognizes an additional SIM card that has been inserted.
The additionally inserted SIM card may not be protected by a PIN.
Only 1.8 V SIM cards are recognized.
1 → 2 →
1.
2.
T20
A0042838 A0044342
‣Open the connection
compartment cover.
‣Remove the plastic cover of the SIM card slot.
‣Insert the SIM card.
‣Put the plastic cover of the SIM card slot back on.
3
T20
1.
2.
2.5 Nm
(1.8 lbf ft)
A0042855
‣Close the connection
compartment cover.

Proline 800 Cellular radio Mounting
Endress+Hauser 19
4.2 Transmitter post-installation check
The post-installation check must always be performed after the following tasks:
• Mounting the transmitter housing:
• Post mounting
• Wall mounting
• Turning the transmitter housing
Is the device undamaged (visual inspection)? 
Turning the transmitter housing:
• Is the securing screw firmly tightened?
• Is the connection compartment cover screwed on tightly?
• Is the securing clamp tightened correctly?

Post and wall mounting:
Are the securing screws tightened securely? 

Electrical connection Proline 800 Cellular radio
20 Endress+Hauser
5 Electrical connection
NOTICE
In the device versions with a mains connection (order code for "Power supply" option K or
S), the device does not have an internal circuit breaker to disconnect from the power
supply network.
‣For this reason, assign the measuring device a switch or power-circuit breaker so that the
power supply line can be easily disconnected from the mains.
‣Although the measuring device is equipped with a fuse, additional overcurrent protection
(maximum 16 A) should be integrated into the system installation.
5.1 Electrical safety
In accordance with applicable national regulations.
5.2 Connecting requirements
5.2.1 Required tool
• Torque wrench
• For cable entries: use appropriate tool
• Wire stripper
• When using stranded cables: crimper for wire end ferrule
• For removing cables from terminal: flat blade screwdriver ≤ 3 mm (0.12 in)
5.2.2 Requirements for connecting cable
The connecting cables provided by the customer must fulfill the following requirements.
Permitted temperature range
• The installation guidelines that apply in the country of installation must be observed.
• The cables must be suitable for the minimum and maximum temperatures to be expected.
Power supply cable (incl. conductor for the inner ground terminal)
Standard installation cable is sufficient.
Signal cable
Pulse /switch output
Standard installation cable is sufficient.
Connecting cable for remote version
The remote version is connected via an electrode cable and a coil current cable.
For detailed information about the specification of the connecting cables, see the
Operating Instructions for the device.