Endress+Hauser Fieldgate FXA720 User manual

BA030S/04/en/07.07
Product Version 2.00.xx
56004856
Operating Instructions
Fieldgate FXA720
Ethernet/PROFIBUS DP gateway with Web server
8

Fieldgate FXA720
Endress+Hauser 1
Table of Contents
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Software Compatibility . . . . . . . . . . . . . . . . . . . . . . 3
Registered Trademarks . . . . . . . . . . . . . . . . . . . . . . . 3
1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Installation, commissioning and operation . . . . . . . . 3
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4 Technical improvement . . . . . . . . . . . . . . . . . . . . . . 3
1.5 Declaration of conformity . . . . . . . . . . . . . . . . . . . . 4
1.6 Writing conventions . . . . . . . . . . . . . . . . . . . . . . . . 5
1.7 Drawing conventions . . . . . . . . . . . . . . . . . . . . . . . 6
2 Identification . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Licensing agreement . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Function and System Design . . . . . . . . . . 8
3.1 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2 Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2.1 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2.2 Display elements (LEDs) . . . . . . . . . . . . . . . 9
3.3 System architecture . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4 System requirements . . . . . . . . . . . . . . . . . . . . . . . 12
4 Hardware Installation . . . . . . . . . . . . . . . 13
4.1 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2.1 Power supply . . . . . . . . . . . . . . . . . . . . . . 14
4.2.2 Communication ports . . . . . . . . . . . . . . . . 15
5 Getting Started . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Preparing for installation . . . . . . . . . . . . . . . . . . . . 16
5.1.1 Checking the system requirements . . . . . . 16
5.1.2 Installing the documentation . . . . . . . . . . . 17
5.1.3 Adobe Acrobat Reader . . . . . . . . . . . . . . . . 17
5.2 Establishing communication . . . . . . . . . . . . . . . . . 18
5.2.1 Making initial contact . . . . . . . . . . . . . . . . 18
5.2.2 Changing the Fieldgate address . . . . . . . . . 20
5.3 Installing FXA720 PROFIBUS Driver . . . . . . . . . . . 21
5.3.1 Installing the driver . . . . . . . . . . . . . . . . . . 21
5.3.2 Configuring the driver . . . . . . . . . . . . . . . . 23
5.3.3 Setting PROFIBUS DP bus parameters
in FieldCare . . . . . . . . . . . . . . . . . . . . . . . 26
5.3.4 Setting PROFIBUS DP bus parameters
in P View . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.4 Modifying, repairing or removing the application . . 28
5.4.1 Fieldgate FXA720 PROFIBUS Driver . . . . . 28
5.4.2 Fieldgate FXA720 documentation . . . . . . . 28
6 Configuring the Web Server . . . . . . . . . 29
6.1 Logging on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.2 User interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.2.1 Menu bar . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.2.2 Navigation bar . . . . . . . . . . . . . . . . . . . . . . 31
6.2.3 Information & Configuration pages . . . . . . . 32
6.3 Fieldgate location page . . . . . . . . . . . . . . . . . . . . . . 33
6.4 Security setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.5 Network setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.5.1 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.5.2 E-mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.5.3 Time server . . . . . . . . . . . . . . . . . . . . . . . . 37
6.6 PROFIBUS setup . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6.6.1 Communication settings . . . . . . . . . . . . . . 38
6.6.2 Scan settings . . . . . . . . . . . . . . . . . . . . . . . 40
6.6.3 Live list . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.7 Overview of selected devices . . . . . . . . . . . . . . . . . 41
6.7.1 Device detail parameters . . . . . . . . . . . . . . 42
6.7.2 E-mail on alarm . . . . . . . . . . . . . . . . . . . . . 42
6.7.3 Expert mode for Slot/Index configuration . 43
7 Viewing Information (User Mode) . . . 44
7.1 Logging on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
7.2 Live list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
7.3 Overview of selected devices . . . . . . . . . . . . . . . . . 46
7.4 Fieldgate information . . . . . . . . . . . . . . . . . . . . . . . 47
7.5 XML export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.6 Other view functions . . . . . . . . . . . . . . . . . . . . . . . 49
7.6.1 Refresh function . . . . . . . . . . . . . . . . . . . . 49
7.6.2 Endress+Hauser function . . . . . . . . . . . . . . 49
8 Firmware Update . . . . . . . . . . . . . . . . . . . 50
9 Trouble-Shooting . . . . . . . . . . . . . . . . . . . 51
9.1 Problems and remedies . . . . . . . . . . . . . . . . . . . . . 51
9.2 FAQ - Frequently Asked Questions . . . . . . . . . . . . . 51
9.3 Troubleshooting on no connection . . . . . . . . . . . . . 52
10 Accessories . . . . . . . . . . . . . . . . . . . . . . . . 53
10.1 E+H power supply units . . . . . . . . . . . . . . . . . . . . 53
11 Technical Data . . . . . . . . . . . . . . . . . . . . . 54
12 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . 55
12.1 Changing the Internet address (Windows 2000) . . . 55
12.2 XML data elements . . . . . . . . . . . . . . . . . . . . . . . . 57
12.3 PROFIBUS bus parameter ranges . . . . . . . . . . . . . . 58
Index . . . . . . . . . . . . . . . . . . . . . . . . . 59

Fieldgate FXA720
2Endress+Hauser
Revision History
Software Compatibility
* Also supplied with FieldCare, backwards compatible.
Registered Trademarks
PROFIBUS
®
Registered trademark of the PROFIBUS User Organisation, Karlsruhe Germany.
Microsoft
®
, Windows
®
, Windows 2000
®
,Windows XP
®
and the Microsoft logo are registered
trademarks of the Microsoft Corporation.
All other brand and product names are trademarks or registered trademarks of the companies and
organisations in question
Product
version Manual Changes Remarks
1.00.xx BA030S/04/en/02.04 Original manual
1.01.xx BA030S/04/en/12.04 Single channel version
Getting started revised
Update of user interface
Addition of limit alarms
New security set-up
E-mails now possible
Chapter 4 revised accordingly
Chapter 5 describes web and pass through set-up
Chapter 7.2
Chapter 7.4
Chapter 7.5, Maintenance user added
Chapter 7.6
2.00.xx BA030S/04/en/07.07 Product Java Applets no longer supported
Revision of Web server pages
Editorial Removal of Java Applets
TOF-Tool/Commuwin II replaced by Fieldgate
Product
version DTM (PROFIdtmDPV1) PROFIBUS Driver PROFIBUS DP OPC Server
Supplied on Fieldgate FXA720 CD-ROM Purchased Separately
1.00.xx Version 1.00 (74)* Version 26.00.00 Version 1.15
1.01.xx Version 1.00 (74)* Version 27.00.00 Version 2.00
2.00.xx Version 1.00 (74)* Version 27.00.00 Version 2.00

Fieldgate FXA720 1 Safety
Endress+Hauser 3
1 Safety
1.1 Designated use
Fieldgate FXA720 is a PROFIBUS/Ethernet Gateway with integrated web server that can be used:
• as a PROFIBUS DP/Ethernet gateway within a PROFIBUS monitoring and control system
• as a remote data acquisition module for PROFIBUS devices connected to its PROFIBUS DP
channels.
More information on these applications is to be found in the manual, or visit the Fieldgate web page
at www.products.endress.com/fieldgate.
1.2 Installation, commissioning and operation
Fieldgate FXA720 must be installed, connected, operated and maintained according to the
instructions in this manual: personnel must be authorised and suitably qualified.
Warning
• You require a unique IP address to set up Fieldgate. The use of IP addresses is strictly
controlled. Usually your system administrator will be authorised to allocate unique addresses
for your Fieldgates. Assigning an unauthorised address to a Fieldgate may result in conflicts
within your system and the failure of the associated devices!
1.3 Operational safety
The unit must not be used in explosion hazardous areas. The permissible ambient conditions given
in the technical data must be complied with.
Repair Do not open the housing of the Fieldgate FXA720. It does not contain any parts that need to be
maintained or repaired by the user. In the event of a fault or defect, return the unit to the vendor.
Opening the unit will void the warranty!
1.4 Technical improvement
Endress+Hauser reserves the right to make technical improvements toits hardware and software at
any time and without prior notification. Where such improvements have no effect on the operation
of the equipment, they are not documented. If the improvements effect operation, a new version of
the operating instructions is normally issued, see Revision History.

1Safety Fieldgate FXA720
4Endress+Hauser
1.5 Declaration of conformity
CE Notice Fieldgate FXA720 complies with the requirements of the EC Directives 89/336/EEC
"Electromagnetic Compatibility" (EMC directive).
• Emission: EN 50022:1998 Class A (ITE Product Standard)
EN 50011:1998 Group 1 Class A (ISM Product Standard)
• Immunity: EN 61000-4-5:1999 Generic Immunity Standard
EN 61000-4-3: 1996 RF Electromagnetic Fields
A Declaration of Conformity in compliance with the above standards has been made and can be
inspected at Endress+Hauser Process Solutions AG on request.
North America Fieldgate FXA720 conforms with the following North American Electromagnetic Compatibility
standards:
• UL 508: Industrial Control Equipment
• CSA C22.2 # 14.795: Industrial Control Equipment
Note!
• For compliance with the legal EMC requirements, the other components (AC adapter, PROFIBUS
stations, etc.) must also meet these requirements.
• To meet the EMC conditions, the device must be installed andconnectedin accordance with the
Installation Instructions.
Warning!
• This is a Class A product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
FCC This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

Fieldgate FXA720 1 Safety
Endress+Hauser 5
1.6 Writing conventions
The following writing conventions and symbols have been used to provide the user with a better
overview of the contents of this manual and to highlight important information:
Text emphasis The following table provides you with a brief overview of the methods used to emphasise text in
this manual.
Safety conventions Safety relevant information is highlighted by an icon in the margin plus the note, caution or warning
text.
.
Text emphasis Function Example
" Bold in inverted
commas " Keys, buttons, program icons, tabs, menus, commands "
Start => Programs => Endress+Hauser "
or " Enter "
Select " Print " in the " File " menu.
With the CTRL key (CONTROL key) held down,
press the SHIFT key. Keep the "
CTRL key " pressed and press
the " SHIFT key ".
With the CTRL key (CONTROL key) held down,
click the left mouse button. Keep the "
CTRL key " pressed and left-
click the mouse.
CAPS Details on paths and file names in the text DOKUFMR2XX.PDF or WIN.HLP
Angle brackets Variables <CD-ROM drive>
Icon Meaning
Note!
A note highlights actions or procedures which, if not performed correctly, may indirectly affect operation
or may lead to an instrument response which is not planned
Caution!
Caution highlights actions or procedures which, if not performed correctly, may lead to personal injury or
incorrect functioning of the instrument
Warning!
A warning highlights actions or procedures which, if not performed correctly, will lead to personal injury,
a safety hazard or destruction of the instrument

1Safety Fieldgate FXA720
6Endress+Hauser
1.7 Drawing conventions
The following symbols may be found within technical drawings.
Explosion protection .
Electrical symbols .
Icon Meaning
Device certified for use in explosion hazardous area
If the device has this symbol embossed on its name plate it can be installed in an explosion hazardous area
in accordance with the specifications in the certificate or in a safe area
Explosion hazardous area
Symbol used in drawings to indicate explosion hazardous areas. Devices located in and wiring entering
areas with the designation “explosion hazardous areas” must conform with the stated type of protection
Safe area (non-explosion hazardous area)
Symbol used in drawings to indicate, if necessary, non-explosion hazardous areas. Devices located in safe
areas stiill require a certificate if their outputs run into explosion hazardous areas.
Icon Meaning
Direct voltage
A terminal to which or from which a direct current or voltage may be applied or supplied
Alternating voltage
A terminal to which or from which an alternating (sine-wave) current or voltage may be applied or
supplied
Grounded terminal
A grounded terminal, which as far as the operator is concerned, is already grounded by means of an earth
grounding system
Protective grounding (earth) terminal
A terminal which must be connected to earth ground prior to making any other connection to the
equipment
Equipotential connection (earth bonding)
A connection made to the plant grounding system which may be of type e.g. neutral star or equipotential
line according to national or company practice

Fieldgate FXA720 2 Identification
Endress+Hauser 7
2 Identification
2.1 Device designation
The device designation is to be found on the nameplate affixed to the righthand side of the module
.
The device type can be derived from the product code as follows:
2.2 Scope of delivery
Please check that the delivery is complete and free of defects before starting installation. The scope
of delivery comprises the following parts:
• Fieldgate FXA720 gateway
• 24V female plug connector
• Profibus drivers and installation manual (on CD-ROM)
• "Getting Started" manual (printed document)
• If appropriate, additional software licences including documentation
2.3 Licensing agreement
The PROFIBUS driver supplied with the Setup CD can be used on any computer that is to be used
with Fieldgate FXA720. The license agreement is on the Setup CD.
The software required for start-up and commissioning is freely available or is subject to the licensing
conditions of its manufacturer. Installation of the software on your computer implies that you accept
the terms of the corresponding licensing agreement.
Root Description
FXA720- 1
2
3
4
9
No. of Channels
1x PROFIBUS port
2x PROFIBUS ports
3x PROFIBUS ports
1x PROFIBUS port, small housing
Special version
E
Y
Power Supply
24 VDC (+/- 20%)
Special version
1
9
Modem Interface
Ethernet 100Base-Tx/10Base-T
Special version
A
Y
DAT Module
Without DAT module
Special version
Name
Device information
Power requirement
ControlCare
Fieldgate FXA720
FXA720 3E1A
2.00
Ser. No.: 6A000124038
Order Code:
+24VDC +/-10%, max 3A
HW. Version:

3 Function and System Design Fieldgate FXA720
8Endress+Hauser
3 Function and System Design
3.1 Function
Fieldgate FXA720 connects host systems to PROFIBUS DP networks via Ethernet. It can be
equipped with up to three RS-485 ports, each giving access to up to 125 PROFIBUS DP devices.
Fieldgate is designed for Windows and web-based applications such as configuration, monitoring,
and visualisation. Process data can be monitored with the integrated Web server.
Fieldgate can also be integrated into system applications via OPC, DTM or XML, eg.:
• OPC for exchanging data with applications such as SCADA/HMI OPC clients,
e.g. P View SPV200
• DTM for exchanging data with FDT frame applications, e.g. FieldCare
• XML for exchanging data with Microsoft Office applications or simple visualisation applications
such as Field Viewer SPV10