Endress+Hauser dosimass User manual

Products Solutions Services
Operating Instructions
Dosimass
Coriolis flowmeter
BA00097D/06/EN/16.15
71291279
Valid as of version
03.00.zz (Device firmware)

Dosimass
2 Endress+Hauser
• Make sure the document is stored in a safe place such that it is always available when
working on or with the device.
• To avoid danger to individuals or the facility, read the "Basic safety instructions" section
carefully, as well as all other safety instructions in the document that are specific to
working procedures.
• The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser Sales Center will supply you with current information and updates to
these instructions.

Dosimass Table of contents
Endress+Hauser 3
Table of contents
1 Document information .............. 5
1.1 Document function ..................... 5
1.2 Symbols used .......................... 5
1.2.1 Safety symbols .................. 5
1.2.2 Electrical symbols ................ 5
1.2.3 Symbols for certain types of
information .................... 5
1.2.4 Symbols in graphics ............... 6
1.3 Documentation ........................ 6
1.3.1 Standard documentation ........... 6
1.3.2 Supplementary device-dependent
documentation .................. 7
1.4 Registered trademarks ................... 7
2 Basic safety instructions ............ 8
2.1 Requirements for the personnel ............ 8
2.2 Designated use ........................ 8
2.3 Workplace safety ....................... 9
2.4 Operational safety ...................... 9
2.5 Product safety ......................... 9
2.6 IT security ........................... 10
3 Product description ................ 11
3.1 Product design ........................ 11
4 Incoming acceptance and product
identification ..................... 12
4.1 Incoming acceptance ................... 12
4.2 Product identification ................... 12
4.2.1 Sensor nameplate ............... 13
4.2.2 Symbols on measuring device ...... 14
5 Storage and transport ............. 15
5.1 Storage conditions ..................... 15
5.2 Transporting the product ................ 15
5.3 Packaging disposal ..................... 15
6 Installation ....................... 16
6.1 Installation conditions .................. 16
6.1.1 Mounting position ............... 16
6.1.2 Requirements from environment and
process ....................... 19
6.1.3 Special mounting instructions ...... 21
6.2 Mounting the measuring device ........... 22
6.2.1 Required tools .................. 22
6.2.2 Preparing the measuring device ..... 23
6.2.3 Mounting the measuring device ..... 23
6.3 Post-installation check .................. 23
7 Electrical connection .............. 24
7.1 Connection conditions .................. 24
7.1.1 Requirements for connecting cable ... 24
7.1.2 Terminal assignment ............. 24
7.1.3 Pin assignment, device plug ........ 25
7.1.4 Requirements for the supply unit .... 26
7.2 Connecting the measuring device .......... 26
7.2.1 Connecting the transmitter ........ 26
7.3 Ensuring the degree of protection .......... 26
7.4 Post-connection check .................. 27
8 Operation options ................. 28
8.1 Overview of operating options ............ 28
8.2 Access to the operating menu via the
operating tool ........................ 28
8.2.1 Connecting the operating tool ...... 28
8.2.2 FieldCare ..................... 29
8.2.3 DeviceCare .................... 30
9 System integration ................ 31
9.1 Overview of device description files ......... 31
9.1.1 Current version data for the device ... 31
9.1.2 Operating tools ................. 31
10 Commissioning .................... 32
10.1 Function check ....................... 32
10.2 Switching on the measuring device ......... 32
10.3 Establishing a connection via FieldCare ...... 32
10.4 Configuring the measuring device .......... 32
10.4.1 Defining the tag name ............ 33
10.4.2 Setting the system units .......... 33
10.4.3 Configuring the pulse/frequency/
switch output .................. 35
10.4.4 Low flow cut off ................ 40
10.4.5 Detection of partially filled pipes .... 41
10.5 Advanced settings ..................... 41
10.5.1 Sensor adjustment ............... 42
10.5.2 Configuring the totalizer .......... 42
10.6 Simulation ........................... 43
11 Operation ......................... 45
11.1 Reading device locking status ............. 45
11.2 Reading access authorization status on
operating software ..................... 45
11.3 Reading measured values ................ 45
11.3.1 Process variables ................ 45
11.3.2 Totalizer ...................... 46
11.3.3 Output values .................. 47
11.4 Performing a totalizer reset .............. 47
12 Diagnostics and troubleshooting ... 49
12.1 General troubleshooting ................. 49

Table of contents Dosimass
4 Endress+Hauser
12.2 Diagnostic information in FieldCare ........ 49
12.2.1 Diagnostic options ............... 49
12.2.2 Calling up remedy information ...... 50
12.3 Adapting the diagnostic information ....... 50
12.3.1 Adapting the diagnostic behavior .... 50
12.4 Overview of diagnostic information ........ 50
12.5 Pending diagnostic events ............... 52
12.6 Diagnostic list ........................ 53
12.7 Event logbook ........................ 53
12.7.1 Event history ................... 53
12.7.2 Filtering the event logbook ........ 53
12.7.3 Overview of information events ..... 54
12.8 Resetting the measuring device ........... 54
12.9 Device information .................... 54
12.10 Firmware history ...................... 56
13 Maintenance ...................... 57
13.1 Maintenance tasks ..................... 57
13.1.1 Exterior cleaning ................ 57
13.1.2 Interior cleaning ................ 57
13.2 Measuring and test equipment ............ 57
13.3 Endress+Hauser services ................ 57
14 Repair ............................ 58
14.1 General notes ........................ 58
14.2 Spare parts .......................... 58
14.3 Endress+Hauser services ................ 58
14.4 Return .............................. 58
14.5 Disposal ............................ 58
14.5.1 Removing the measuring device ..... 58
14.5.2 Disposing of the measuring device ... 59
15 Accessories ....................... 60
15.1 Communication-specific accessories ........ 60
15.2 Service-specific accessories ............... 60
16 Technical data .................... 62
16.1 Application .......................... 62
16.2 Function and system design .............. 62
16.3 Input ............................... 62
16.4 Output ............................. 63
16.5 Power supply ......................... 64
16.6 Performance characteristics .............. 65
16.7 Installation .......................... 67
16.8 Environment ......................... 67
16.9 Process ............................. 68
16.10 Mechanical construction ................ 70
16.11 Operability .......................... 71
16.12 Certificates and approvals ............... 72
16.13 Accessories .......................... 73
16.14 Supplementary documentation ............ 73
Index .................................. 75

Dosimass Document information
Endress+Hauser 5
1 Document information
1.1 Document function
These Operating Instructions contain all the information that is required in various phases
of the life cycle of the device: from product identification, incoming acceptance and
storage, to mounting, connection, operation and commissioning through to
troubleshooting, maintenance and disposal.
1.2 Symbols used
1.2.1 Safety symbols
Symbol Meaning
DANGER
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
NOTE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Symbol Meaning Symbol Meaning
Direct current Alternating current
Direct current and alternating current Ground connection
A grounded terminal which, as far as
the operator is concerned, is
grounded via a grounding system.
Protective ground connection
A terminal which must be connected
to ground prior to establishing any
other connections.
Equipotential connection
A connection that has to be connected
to the plant grounding system: This
may be a potential equalization line
or a star grounding system depending
on national or company codes of
practice.
1.2.3 Symbols for certain types of information
Symbol Meaning
Permitted
Procedures, processes or actions that are permitted.
Preferred
Procedures, processes or actions that are preferred.
Forbidden
Procedures, processes or actions that are forbidden.

Document information Dosimass
6 Endress+Hauser
Symbol Meaning
Tip
Indicates additional information.
Reference to documentation
Reference to page
Reference to graphic
,… ,
Series of steps
Result of a step
Help in the event of a problem
Visual inspection
1.2.4 Symbols in graphics
Symbol Meaning Symbol Meaning
1, 2, 3,... Item numbers
,… ,
Series of steps
A, B, C, ... Views A-A, B-B, C-C, ... Sections
-
Hazardous area
.
Safe area (non-hazardous area)
Flow direction
1.3 Documentation
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The CD-ROM provided for the device (depending on the device version, the CD-ROM
might not be part of the delivery!)
• The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate
or scan the 2-D matrix code (QR code) on the nameplate.
For a detailed list of the individual documents along with the documentation code
1.3.1 Standard documentation
Document type Purpose and content of the document
Technical Information Planning aid for your device
The document contains all the technical data on the device and provides
an overview of the accessories and other products that can be ordered for
the device.
Brief Operating Instructions Guide that takes you quickly to the 1st measured value
The Brief Operating Instructions contain all the essential information
from incoming acceptance to initial commissioning.

Dosimass Document information
Endress+Hauser 7
1.3.2 Supplementary device-dependent documentation
Additional documents are supplied depending on the device version ordered: Always
comply strictly with the instructions in the supplementary documentation. The
supplementary documentation is an integral part of the device documentation.
1.4 Registered trademarks
TRI-CLAMP®
Registered trademark of Ladish & Co., Inc., Kenosha, USA
Applicator®, FieldCare®, DeviceCare®
Registered or registration-pending trademarks of the Endress+Hauser Group

Basic safety instructions Dosimass
8 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill
the following requirements:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task
‣Are authorized by the plant owner/operator
‣Are familiar with federal/national regulations
‣Before beginning work, the specialist staff must have read and understood the
instructions in the Operating Instructions and supplementary documentation as well as
in the certificates (depending on the application)
‣Following instructions and basic conditions
The operating personnel must fulfill the following requirements:
‣Being instructed and authorized according to the requirements of the task by the
facility's owner-operator
‣Following the instructions in these Operating Instructions
2.2 Designated use
Application and media
The measuring device described in these Instructions is intended only for flow
measurement of liquids and gases.
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or in applications
where there is an increased risk due to process pressure, are labeled accordingly on the
nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣Only use the measuring device in full compliance with the data on the nameplate and
the general conditions listed in the Operating Instructions and supplementary
documentation.
‣Check the nameplate to verify if the device ordered can be put to its intended use in the
approval-related area (e.g. explosion protection, pressure vessel safety).
‣Use the measuring device only for media against which the process-wetted materials
are adequately resistant.
‣If the measuring device is not operated at atmospheric temperature, compliance with
the relevant basic conditions specified in the associated device documentation is
absolutely essential: "Documentation" section →  6.
‣Protect the measuring device permanently against corrosion from environmental
influences.
Incorrect use
Non-designated use can compromise safety. The manufacturer is not liable for damage
caused by improper or non-designated use.
LWARNING
Danger of breakage of the measuring tube due to corrosive or abrasive fluids or from
environmental conditions.
Housing breakage due to mechanical overload possible!
‣Verify the compatibility of the process fluid with the measuring tube material.
‣Ensure the resistance of all fluid-wetted materials in the process.
‣Keep within the specified pressure and temperature range.

Dosimass Basic safety instructions
Endress+Hauser 9
Verification for borderline cases:
‣For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance
in verifying the corrosion resistance of fluid-wetted materials, but does not accept any
warranty or liability as minute changes in the temperature, concentration or level of
contamination in the process can alter the corrosion resistance properties.
Residual risks
The external surface temperature of the housing can increase by max. 20 K due to the
power consumption of the electronic components. Hot process fluids passing through the
measuring device will further increase the surface temperature of the housing. The surface
of the sensor, in particular, can reach temperatures which are close to the fluid
temperature.
Possible burn hazard due to fluid temperatures!
‣For elevated fluid temperature, ensure protection against contact to prevent burns.
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
For welding work on the piping:
‣Do not ground the welding unit via the measuring device.
If working on and with the device with wet hands:
‣It is recommended to wear gloves on account of the higher risk of electric shock.
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
‣If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability,
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to repair of an electrical device.
‣Use original spare parts and accessories from Endress+Hauser only.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet
state-of-the-art safety requirements, has been tested, and left the factory in a condition in
which it is safe to operate.
It meets general safety standards and legal requirements. It also complies with the EC
directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser
confirms this by affixing the CE mark to the device.

Basic safety instructions Dosimass
10 Endress+Hauser
2.6 IT security
We only provide a warranty if the device is installed and used as described in the
Operating Instructions. The device is equipped with security mechanisms to protect it
against any inadvertent changes to the device settings.
IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.