Endress+Hauser Flowphant T DTT31 Manual

TI00125R/09/en
71009492
Technical information
Flow switch
Flowphant®T DTT31, DTT35
Flow switch for safe monitoring of mass flow and temperature in
industrial processes
Application
Flow switch for monitoring and displaying relative mass flow
rates of liquid media in the range from
0.03 to 3 m/s (0.1 to 9.84 ft/s):
Flowphant®T DTT31
−with thread connections or coupling
Flowphant®T DTT35
−with process connections for hygienic applications
Application examples:
• Monitoring cooling water circulation systems of pumps,
turbines, compressors and heat exchangers
• Monitoring pump functionality
• Leak monitoring in process lines
• Monitoring lubrication systems
• Filter monitoring in the beverage industry
Benefits at a glance
This compact flow switch impresses with the latest in
technology being used:
• Practically no pressure loss
• Configuration software ReadWin®2000 or FieldCare for
quick configuration and reliable storage of device settings
• Optional: 4 to 20 mA analog output to read out the flow rate
as percentage value
• Optional: second switch output or 4 to 20 mA analog output
for temperature monitoring
• Function check and process information onsite thanks to
digital display at device
• Top housing section which can be rotated 310° and rotatable
display make it possible to read the measured values in all
orientations
• DTT35: 3-A marked

DTT31, DTT35
2Endress+Hauser
Function and system design
Measuring principle
T09-DTT31xxx-15-xx-xx-xx-000
The device measures the mass flow of a liquid medium with the calorimetric measurement method. The
calorimetric measuring principle is based on cooling a heated temperature sensor. Heat is removed from the
sensor by forced convection due to medium flowing by. The extent of this heat transfer depends on the medium
velocity and the difference in temperature between the sensor and medium (King's law). The higher the
velocity or the mass flow of the medium, the greater the temperature sensor cooling.
Measuring system Overview
Flowphant®
product family
DTT31 DTT35
a0005276 T09-TTR35xxx-14-xx-xx-xx-000
Measurement
probe
RTD RTD
Field of
application
Monitoring of the mass flow of water, water-
like substances and low-viscosity oils.
Monitoring of the mass flow of liquid media
in hygienic processes.
Process
connection
• Compression fitting
•Thread:
−G½" and G¼"
−ANSI NPT ¼" and NPT ½"
•Hygiene:
−Conical metal-metal G½"
−Clamp 1" - 1½", 2"
−Varivent F, N
−DIN 11851
−APV-Inline
Measuring range Mass flow as a relative value between 0 and 100%.
Process measuring limit, liquids: 0.03 to 3 m/s (0.1 to 9.84 ft/s)

DTT31, DTT35
Endress+Hauser 3
DC voltage version
PNP switch output of electronics.
Power supply e.g. with a power supply unit.
Preferably in conjunction with programmable logic controllers (PLC) or for controlling a relay.
a0005373
A: 1x PNP switch output
B: 2x PNP switch output
C: PNP switch output with additional analog output 4 to 20 mA
mTransmitter power supply unit, e.g. RNB130
nLoad (e.g. programmable logic controller, process control system, relay)
o Display e.g. RIA452 or recorder e.g. Ecograph T or Minilog B (at 4 to 20 mA analog output)
mPower supply "Easy Analog RNB130":
Primary switched-mode power supply for sensors. Space saving DIN rail mounting as per IEC 60715.
Wide-range nominal voltage input: 100 to 240 V AC; Output: 24 V DC, max. 30 V in the event of a fault;
Nominal output current: 1.5 A. Connection to monophased a.c. networks or to two phase conductors of three-
phase supply networks.
n Process display RIA452:
If you would like to read off the instantaneous value of the temperature not only locally, but also e.g. directly
from a control room or in the PC network, then one suitable device is the process display RIA452:
Digital process display unit in 96 x 96 mm (3.78 x 3.78 in) panel mounted housing for monitoring and
displaying analog measured values with pump control and batch functions. Multicoloured 7-digit 14-segment
LC display with large bargraph. Configuration and visualisation via RS232 interface and ReadWin®2000 PC
operating software.
o Multi Channel Recorder Ecograph T, Data logger Minilog B:
If you would like to read off the instantaneous value of the temperature not only locally, but also record, analyze
and display it e.g. directly from a control room or in the PC network, then the following devices are suitable:

DTT31, DTT35
4Endress+Hauser
• Multi Channel Recorder Ecograph T
144 x 144 mm (5.67 x 5.67 in) panel mounted housing for electronic acquisition, display, recording,
analysis, remote transmission and archiving of analog and digitalinput signals. Data recording system with
CompactFlash card and multi-coloured LCD display (120 mm / 4.7 in screen size). Configuration and
visualisation via interface (USB, Ethernet, RS232/485) and ReadWin®2000 PC operating software.
• Data logger Minilog B
Battery powered measured value collector with 2 input channels for storing analog and digital values.
Internal memory 128 kB for max. 84000 measured values. Configuration and visualisation via RS232
interface and ReadWin®2000 PC operating software. Optionally with telealarm function.
Input
Measured variable • Flow velocity of liquid media (calorimetric measuring principle)
• Temperature (RTD), optional for two switch outputs or additional analog output
Measuring range • Flow: 0.03 m/s to 3 m/s (0.1 to 9.84 ft/s), as relative value between 0 and 100%; maximum display
resolution: 1%
• Temperature: -20 °C to +85 °C (-4 to +185 °F); display resolution: 1 °C (1 °F)
Output
Output signal DC voltage version: (short-circuit proof version)
• 1x PNP switch output (flow) or
• 2x PNP switch outputs (flow or temperature, adjustable) or
• 1x PNP switch output and 1x 4 to20 mA output, active (flow or temperature, adjustable)
!Note!
The analog output reads out the measured flow rate as relative value in percentage of the adjusted measuring
range.
Signal on alarm Signal on alarm as per NAMUR NE43
• Underranging: Linear drop to 3.8 mA
• Overranging: Linear rise to 20.5 mA
• Sensor break; sensor short-circuit:
≤3.6 mA or ≥21.0 mA (at settings ≥21.0 mA, 21.7 mA output is guaranteed)
• Switch outputs: at safety condition (switch open)
Load Max. (Vpower supply - 6.5 V) / 0.022 A (current output)
Range of adjustment • Switch output
Switch point (SP) and switchback point (RSP) in increments of 1% with min. hysteresis of 5%
• Damping: freely adjustable: 0 = off (no damping) or 10 to 40 s in increments of 1 second
• Unit: %, optional °C, °F (with two outputs and temperature monitoring)
Switching capacity DC voltage version:
• Switch status ON: Ia≤250 mA, switch status OFF: Ia≤1 mA
• Switching cycles: > 10,000,000
• Voltage drop PNP: ≤2 V
• Overload protection
Automatic testing of switching current; output is switched off in case of overcurrent, the switching current
is tested again every 0.5 s; max. capacitance load: 14 μF for max. supply voltage (without resistive load)
Periodic disconnection from a protective circuit in event of overcurrent (f = 2 Hz) and indication of
’Warning’

DTT31, DTT35
Endress+Hauser 5
Inductive load To prevent electrical interference, only operate an inductive load (relays, contactors, solenoid valves) when
directly connected to a protective circuit (free-wheeling diode or capacitor).
Power supply
Electrical connection Plug connection
!Note!
DTT35: Electrical cables must comply with 3-A standard, must be smooth, corrosion resistantand cleanable.
T09-TTR31xxx-04-00-xx-xx-000
A: M12x1 connector
B: Valve connector M16x1.5 or NPT ½"
Device connection
• DC voltage version with M12x1 connector
a0006818
Item No. Output setting Order code (see Ordering information section)
A1 1x PNP switch output DTT3x-A1A*******
A2 2x PNP switch output R1 and m(R2) DTT3x-A1B*******
A2’ 2x PNP switch output R1 and m(diagnosis/NC
contact with "DESINA" setting)
DTT3x-A1B*******
A3 1x PNP switch output and 1x analog output
(4 to 20 mA)
DTT3x-A1C*******

DTT31, DTT35
6Endress+Hauser
• DC voltage version with valve connector M16x1.5 or NPT ½"
P01-PTx3xxxx-04-xx-xx-xx-003
Supply voltage DC voltage version
18 up to 30 V DC (reverse polarity protection)
Current consumption < 100 mA (without load) at 24 V DC, max. 150 mA (without load); with reverse polarity protection
Power supply failure • Behaviour in case of overvoltage (> 30 V)
The device works continuously up to 34 V DC without any damage.
No damage is caused to the device in case of a short-term overvoltage up to 1 kV (as per EN 61000-4-5).
The specific properties are no longer guaranteed if the supply voltage is exceeded.
• Behaviour in case of undervoltage
If the supply voltage drops below the minimum value, the device switches off (status as if not supplied with
power = switch open).
Performance characteristics
The percentage information in the "Performance characteristics" section refers to the full scale value or the set
maximum value (100% value) of the monitoring range.
Reference operating
conditions
As per DIN IEC 60770 or DIN IEC 61003
T = 25 °C ± 5 °C (77 °F ± 9 °F), relative humidity 45 to 75 %, ambient air pressure 860 to 1060 kPa
(124 to 153 PSI), water test medium. Supply voltage U = 24 V DC.
Maximum measured error Flow
The device records fluid velocity relatively in relation to a set monitoring range of the flow (0 to 100 % as
display value). An absolute measurement of the fluid velocity or the mass flow is not possible. The sensitivity
of the calorimetric flow sensor changes with the fluid velocity. It increases with decreasing fluid velocity (for
example, with water, the greatest sensor sensitivity is recorded in the range from 0.03 to 0.5 m/s).
Item No. Output setting Order code (see Ordering information section)
B 1x PNP switch output DTT3x-A2A*******; DTT3x-A3A*******

DTT31, DTT35
Endress+Hauser 7
a0008181-en
Standard characteristic
A, B: Set monitoring ranges of the flow (example)
LOWF 0%: Setting for the minimum fluid velocity occurring in the monitoring range A or B (0% value)
HIF 100%: Setting for the maximum fluid velocity occurring in the monitoring range A or B (100% value)
Temperature
• Accuracy: 2 K (3.6 °F)
• Repeatability: 1 K (1.8 °F)
• Influence of medium temperature: 0.05 %/K of full scale value
Switch point non-repeatability
Temperature gradient In the event of a temperature change of ≥0.5 K/min in the medium, temporary display drifts are possible which
can exceed the specified non-reproducibility values of the switch point.
Sensor reaction time 6 to 12 s
Long-term drift 0.5% per year under reference operating conditions
Long-term reliability Mean time between failure (MTBF) > 100 years
(calculated according to "British Telecom Handbook of Reliability Data No. 5")
Switch output response time 100 ms
Analog output • Maximum measured error = switch point error and display error + 0.1%
• Rise time T90: ≤200 ms
• Settling time T99: ≤500 ms
Measuring range
(water as medium)
% of maximum value Influence of
medium temperature1)
1) The values indicated only apply to the device itself without taking the temperature-dependent change of the thermo-
physical properties of the medium into account. For this reason, we recommend you commission the device at the
process temperature and set the switch points (see 'Learn function' →ä12)
Influence of
ambient temperature
0.03 to 0.5 m/s
(0.1 to 1.6 ft/s)
≤2 % 0.05 %/K 0.04 %/K
0.03 to 1 m/s
(0.1 to 3.28 ft/s)
≤3 % 0.10 %/K 0.05 %/K
0.03 to 2 m/s
(0.1 to 6.56 ft/s)
≤5 % 0.15 %/K 0.10 %/K
0.03 to 3 m/s
(0.1 to 9.84 ft/s)
≤10 % 0.20 %/K 0.30 %/K

DTT31, DTT35
8Endress+Hauser
Operating conditions: Installation instructions
Installation instructions
• Electrical rotation of display by 180°
• Housing can be rotated up to 310 ° mechanically
Orientation
No restrictions, but self draining.
Inlet and outlet run
The sensor requires a fully developed flow profile for correct monitoring. For this reason, steadying sections
(5x DN) must be provided in the pipe after a pump, pipe bend, internal fittings and cross-sectional changes.
• The sensor tip should be completely surrounded by medium.
• Position the sensor tip in the area of maximum fluid velocity
(pipe center).
• Minimum sensor immersion length: Li≥10 mm (0.4 in)
A0007163
Installation conditions
Orientation
• For horizontal pipes: lateral installation.
!Note!
Installation from above only if the pipe is completely filled
with medium.
• For vertical pipes: installation in the ascending pipeline.
• DTT35: min. 3° inclination, because of self draining.
A0006977
Correct orientation
"Caution!
• Do not install in down pipes open towards the end.
• The sensor tip should never touch the pipe wall.
A0006978
Incorrect installation!

DTT31, DTT35
Endress+Hauser 9
Operating conditions: Environment
Ambient temperature range –40 up to +85 °C (-40 to +185 °F)
Storage temperature –40 up to +85 °C (-40 to +185 °F)
Climate class 4K4H as per DIN EN 60721-3-4
Degree of protection IP 65 (complete housing)
Shock resistance 50 g as per DIN IEC 68-2-27 (11 ms)
Vibration resistance • 20 g as per DIN IEC 68-2-6 (10-2000Hz)
• 4 g as per German Lloyd GL Guidelines
Electromagnetic compatibility • Interference emission as per IEC 61326 Series, class B electrical equipment
• Interference immunity as per IEC 61326 Series, appendix A (industrial use) and NAMUR Recommendation
NE 21
EMC influence: ≤0.5 %
Operating conditions: Process
Process temperature limits -20 to +85 °C (-4 to +185 °F)
!Note!
The sensor can be exposed up to 130 °C (266 °F) without damage; monitoring switches off automatically at
T ≥85 °C (185 °F) and starts again at T ≤ 85 °C (185 °F).
Process pressure limits Maximum permitted process pressure pmax ≤10 MPa = 100 bar (1450 psi)
"Caution!
The maximum process pressure for the conical metal-metal process connection (MB option) for the DTT35 is
1.6 MPa = 16 bar (232 psi)!
Process flow limit Liquids: 0 up to 3.0 m/s (0 up to 9.84 ft/s)
Operating range Liquids: 0.03 up to 3.0 m/s (0.1 up to 9.84 ft/s)

DTT31, DTT35
10 Endress+Hauser
Mechanical construction
Design, dimensions DTT31,
DTT35
Dimensions
a0005279
All dimensions in mm (in)
L = insertion length (see ordering information, Pos. 080)
Connector M12x1 as per IEC 60947-5-2 (see ordering information, Pos. 020)
Valve connector M16x1.5 or NPT ½" as per DIN 43650A/ISO 4400 (see ordering information, Pos. 020)
DTT31 design, dimensions for
process connections
a0007101
Process connections DTT31 (see ordering information DTT31, Pos. 080)
Item No. Version DTT31 Insertion length L Thread length L1Screw-in length L2
A Without process connection. For suitable welding bosses and compression
fittings see 'Accessories'.
30 and 100 mm
(1.18 and 3.94 in)
--
B Threaded process connection:
• ANSI NPT ¼" (m= AF14)
• ANSI NPT ½" (m= AF27)
• 14.3 mm (0.56 in)
• 19 mm (0.75 in)
• 5.8 mm (0.23 in)
• 8.1 mm (0.32 in)
C Cylindrical threaded process connection in inches as per ISO 228:
• G¼" (n= AF14)
• G½" (n= AF27)
• 12 mm (0.47 in)
• 14 mm (0.55 in)
-