Endress+Hauser Proline Promag 10 User manual

BA082D/24/ae/09.05
Valid as of software version
V 1.02.00 (electronics board)
Operating Instructions
Proline Promag 10
Electromagnetic Flow Measuring System
6

Brief operating instructions Proline Promag 10
2Endress+Hauser
Brief operating instructions
The brief operating instructions are aimed at helping you commission your measuring device quickly
and easily:
Safety instructions Page 5 ff.
First familiarise yourself with the safety instructions to be able to carry out the following work steps quickly and easily.
Here, you can find information on:
• The designated use of the measuring device
• Operational safety
• The safety symbols and conventions used in the document
▼
Installation Page 10 ff.
The “Installation” section provides you with all necessary information from incoming acceptance and the installation
conditions to be taken into consideration (orientation, mounting location, vibrations, etc.) to the actual installation of the
device, including information on seals, earthing and the torques to be observed for the compact and remote versions.
▼
Wiring Page 33 ff.
The electrical connection of the device and the process for connecting the connecting cable of the remote version are
described in the “Wiring” section. This section also includes the following topics:
• The cable specifications of the coil and signal cable
• The terminal assignment
• The potential equalisation and the degree of protection
▼
Display and operating elements Page 45 ff.
All the display and operating elements available for operating the device are described here.
Furthermore, this section provides you with a description of the procedure for configuring the measuring device via the
function matrix and the HART protocol.
▼
Commissioning Page 56 ff.
By means of the brief commissioning guide (→Page 46), you can put your measuring device into operation quickly and
easily. It enables you to configure important basic functions using the local display, for example the display language,
measured variables, units of measure, type of signal, etc.
In addition, this section also describes the empty-pipe/full-pipe adjustment to be carried out for using empty pipe
detection.
▼
Customer-specific configuration Page 85 ff.
Complex measurement tasks require the configuration of additional functions which you can individually select, set and
adapt to your process conditions using the function matrix.
!Note!
All functions are described in detail, as is the function matrix itself, in the Appendix to these Operating Instructions
→Page 85 ff.
!Note!
Always start trouble-shooting with the checklist on Page 62 if faults occur after commissioning or during operation.
This takes you directly (via various queries) to the cause of the problem and the appropriate remedial measures.

Proline Promag 10 Table of contents
Endress+Hauser 3
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . 5
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Installation, commissioning, operation . . . . . . . . . . . 5
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5 Notes on safety conventions and icons . . . . . . . . . . . 6
2 Identification . . . . . . . . . . . . . . . . . . . . 7
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.1 Nameplate of the transmitter . . . . . . . . . . . . 7
2.1.2 Nameplate of the sensor . . . . . . . . . . . . . . . 8
2.1.3 Nameplate of the connections . . . . . . . . . . . 8
2.2 Certificates and approvals . . . . . . . . . . . . . . . . . . . . 9
2.3 Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 9
3 Installation . . . . . . . . . . . . . . . . . . . . . 10
3.1 Incoming acceptance, transport, storage . . . . . . . . . 10
3.1.1 Incoming acceptance . . . . . . . . . . . . . . . . . 10
3.1.2 Transport . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1.3 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . 12
3.2.1 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2.2 Installation location . . . . . . . . . . . . . . . . . . 12
3.2.3 Orientation . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2.4 Vibrations . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.5 Foundations, supports . . . . . . . . . . . . . . . . 16
3.2.6 Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.7 Nominal diameter and flow rate . . . . . . . . 17
3.2.8 Length of connecting cable . . . . . . . . . . . . 19
3.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3.1 Installing Promag W sensor . . . . . . . . . . . . 20
3.3.2 Installing Promag P sensor . . . . . . . . . . . . . 25
3.3.3 Installing Promag H sensor . . . . . . . . . . . . 29
3.3.4 Rotating the transmitter housing . . . . . . . . 30
3.3.5 Affixing the local display to the
blind version . . . . . . . . . . . . . . . . . . . . . . . 30
3.3.6 Rotating the local display . . . . . . . . . . . . . . 31
3.3.7 Mounting the transmitter
(remote version) . . . . . . . . . . . . . . . . . . . 31
3.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . 32
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . 33
4.1 Connecting the remote version . . . . . . . . . . . . . . . 33
4.1.1 Connecting Promag W/P/H . . . . . . . . . . . 33
4.1.2 Cable specifications . . . . . . . . . . . . . . . . . . 37
4.2 Connecting the measuring unit . . . . . . . . . . . . . . . 38
4.2.1 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 38
4.2.2 Terminal assignment . . . . . . . . . . . . . . . . . 39
4.2.3 HART connection . . . . . . . . . . . . . . . . . . . 39
4.3 Potential equalisation . . . . . . . . . . . . . . . . . . . . . . . 40
4.3.1 Standard . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.3.2 Special cases . . . . . . . . . . . . . . . . . . . . . . . 41
4.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . 43
4.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . 44
5 Operation . . . . . . . . . . . . . . . . . . . . . . 45
5.1 Display and operating elements . . . . . . . . . . . . . . . 45
5.2 Brief guide to the function matrix . . . . . . . . . . . . . . 46
5.2.1 General notes . . . . . . . . . . . . . . . . . . . . . . 47
5.2.2 Enabling the programming mode . . . . . . . . 47
5.2.3 Disabling the programming mode . . . . . . . . 47
5.3 Error message display . . . . . . . . . . . . . . . . . . . . . . 48
5.3.1 Type of error . . . . . . . . . . . . . . . . . . . . . . . 48
5.3.2 Error message types . . . . . . . . . . . . . . . . . . 48
5.4 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.4.1 Operating options . . . . . . . . . . . . . . . . . . . 49
5.4.2 Device variables . . . . . . . . . . . . . . . . . . . . . 50
5.4.3 Switching HART write protection on/off . . 50
5.4.4 Universal / common practice
HART commands . . . . . . . . . . . . . . . . . . . 51
5.4.5 Device status/error messages . . . . . . . . . . . 55
6 Commissioning . . . . . . . . . . . . . . . . . . 56
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.2 Switching on the measuring device . . . . . . . . . . . . 56
6.3 Brief commissioning guide . . . . . . . . . . . . . . . . . . . 56
6.4 Commissioning after installing a
new electronics board . . . . . . . . . . . . . . . . . . . . . . 57
6.4.1 Setup “Commissioning” . . . . . . . . . . . . . . . 57
6.5 Empty-pipe/full-pipe adjustment . . . . . . . . . . . . . . 58
6.5.1 Performing empty-pipe and
full-pipe adjustment (EPD) . . . . . . . . . . . . . 58
7 Maintenance . . . . . . . . . . . . . . . . . . . . 59
7.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 59
7.2 Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
8 Accessories . . . . . . . . . . . . . . . . . . . . . 60
9 Trouble-shooting . . . . . . . . . . . . . . . . . 62
9.1 Trouble-shooting instructions . . . . . . . . . . . . . . . . . 62
9.2 System error messages . . . . . . . . . . . . . . . . . . . . . . 63
9.3 Process error messages . . . . . . . . . . . . . . . . . . . . . . 65
9.4 Process errors without display messages . . . . . . . . . 65
9.5 Response of outputs to errors . . . . . . . . . . . . . . . . . 66
9.6 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
9.7 Removing and installing electronics boards . . . . . . 68
9.7.1 Field housing: removing and installing
electronics boards . . . . . . . . . . . . . . . . . . . 68
9.8 Replacing the device fuse . . . . . . . . . . . . . . . . . . . . 70
9.9 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9.10 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9.11 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Proline Promag 10 Table of contents
4Endress+Hauser
10 Technical data . . . . . . . . . . . . . . . . . . . 72
10.1 Technical data at a glance . . . . . . . . . . . . . . . . . . . 72
10.1.1 Application . . . . . . . . . . . . . . . . . . . . . . . . 72
10.1.2 Function and system design . . . . . . . . . . . . 72
10.1.3 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
10.1.4 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
10.1.5 Power supply . . . . . . . . . . . . . . . . . . . . . . . 73
10.1.6 Performance characteristics . . . . . . . . . . . . 74
10.1.7 Operating conditions: Installation . . . . . . . 74
10.1.8 Operating conditions: Environment . . . . . 75
10.1.9 Operating conditions: Process . . . . . . . . . . 76
10.1.10 Mechanical construction . . . . . . . . . . . . . . 78
10.1.11 Human interface . . . . . . . . . . . . . . . . . . . . 82
10.1.12 Certificates and approvals . . . . . . . . . . . . . 83
10.1.13 Ordering information . . . . . . . . . . . . . . . . 83
10.1.14 Accessories . . . . . . . . . . . . . . . . . . . . . . . . 83
10.1.15 Documentation . . . . . . . . . . . . . . . . . . . . 83
10.2 Measuring tube specifications . . . . . . . . . . . . . . . . 84
10.3 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
11 Appendix. . . . . . . . . . . . . . . . . . . . . . . 85
11.1 Illustration of the function matrix . . . . . . . . . . . . . 85
11.2 Group SYSTEM UNITS . . . . . . . . . . . . . . . . . . . . 86
11.3 Group OPERATION . . . . . . . . . . . . . . . . . . . . . . . 87
11.4 Group USER INTERFACE . . . . . . . . . . . . . . . . . . . 88
11.5 Group TOTALIZER . . . . . . . . . . . . . . . . . . . . . . . . 89
11.6 Group CURRENT OUTPUT . . . . . . . . . . . . . . . . . . 90
11.7 Group PULSE/STATUS OUTPUT . . . . . . . . . . . . . 92
11.7.1 Information on the response
of the status output . . . . . . . . . . . . . . . . . . 94
11.7.2 Switching behaviour
of the status output . . . . . . . . . . . . . . . . . . 95
11.8 Group COMMUNICATION . . . . . . . . . . . . . . . . . 97
11.9 Group PROCESS PARAMETER . . . . . . . . . . . . . . 98
11.10 Group SYSTEM PARAMETER . . . . . . . . . . . . . . 100
11.11 Group SENSOR DATA . . . . . . . . . . . . . . . . . . . . 103
11.12 Group SUPERVISION . . . . . . . . . . . . . . . . . . . . 104
11.13 Group SIMULATION SYSTEM . . . . . . . . . . . . . 106
11.14 Group SENSOR VERSION . . . . . . . . . . . . . . . . . 107
11.15 Group AMPLIFIER VERSION . . . . . . . . . . . . . . . 107
11.16 Factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . 108
11.16.1 SI units
(not for USA and Canada) . . . . . . . . . . . . 108
11.16.2 US units
(only for USA and Canada) . . . . . . . . . . . 110
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Proline Promag 10 Safety instructions
Endress+Hauser 5
1 Safety instructions
1.1 Designated use
The measuring device described in these Operating Instructions is to be used only for measuring the
flow of conductive liquids in closed pipes.
The majority of liquids can be measured as of a minimum conductivity of 50 µS/cm e.g.:
• Acids, alkalis,
• Drinking water, wastewater, sewage sludge,
• Milk, beer, wine, mineral water, etc.
Resulting from incorrect use or from use other than that designated the operational safety of the
measuring devices can be suspended. The manufacturer accepts no liability for damages being
produced from this.
1.2 Installation, commissioning, operation
Note the following points:
• Installation, connection to the electricity supply, commissioning and maintenance of the device
must be carried out by trained, qualified specialists authorised to perform such work by the
facility's owner-operator. The specialist must have read and understood these Operating
Instructions and must follow the instructions they contain.
• The device must be operated by persons authorised and trained by the facility's owner-operator.
Strict compliance with the instructions in these Operating Instructions is mandatory.
• In the case of special fluids (incl. fluids for cleaning), Endress+Hauser will be happy to assist in
clarifying the material resistance properties of wetted parts. However, the user is responsible for
the choice of wetted materials as regards their in-process resistance to corrosion. The
manufacturer refuses to accept liability.
• If welding work is performed on the piping system, do not ground the welding appliance through
the measuring device.
• The installer must ensure that the measuring system is correctly wired in accordance with the
wiring diagrams. The transmitter must be grounded, unless the power supply is galvanically
isolated.
• Invariably, local regulations governing the opening and repair of electrical devices apply.
1.3 Operational safety
Note the following points:
• Measuring systems for use in hazardous environments are accompanied by separate Ex
documentation, which is an integral part of this Operating Manual. Strict compliance with the
installation instructions and ratings as stated in this supplementary documentation is mandatory.
The symbol on the front of this Ex documentation indicates the approval and the test center
(0Europe, 2USA, 1Canada).
• The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser Sales Centre will supply you with current information and updates to these
Operating Instructions.
• The measuring device complies with the general safety requirements in accordance with
EN 61010 and the EMC requirements of EN 61326/A1 (IEC 1326) →Chap. 10.1.12
“Certificates and approvals”, Page 83.
• In the case of the Promag H sensor, the process connection seals must be replaced periodically
depending on the application.

Safety instructions Proline Promag 10
6Endress+Hauser
1.4 Return
The following procedures must be carried out before a flowmeter requiring repair or calibration, for
example, is returned to Endress+Hauser:
• Always enclose a fully completed “Declaration of Contamination” form with the device. Only
then can Endress+Hauser transport, examine and repair a returned device.
!Note!
A copy of the “Declaration of Contamination” can be found at the end of these Operating
Instructions.
• Enclose special handling instructions if necessary, for example a safety data sheet as per
EN 91/155/EEC.
• Remove all fluid residues. Pay special attention to the grooves for seals and crevices which could
contain fluid residues. This is particularly important if the fluid is hazardous to health, e.g.
flammable, toxic, caustic, carcinogenic, etc.
#Warning!
• Do not return a measuring device if you are not absolutely certain that all traces of hazardous
substances have been removed, e.g. substances which have penetrated crevices or diffused
through plastic.
• Costs incurred for waste disposal and injury (caustic burns, etc.) due to inadequate cleaning will
be charged to the owner-operator.
1.5 Notes on safety conventions and icons
The devices are designed to meet state-of-the-art safety requirements. They have been tested and
left the factory in a condition in which they are safe to operate. The devices comply with the
applicable standards and regulations in accordance with EN 61010 “Protection Measures for
Electrical Equipment for Measurement, Control, Regulation and Laboratory Procedures.”
The devices can, however, be a source of danger if used incorrectly or for use other than that
designated. Consequently, always pay particular attention to the safety instructions indicated in
these Operating Instructions by the following symbols:
#Warning!
“Warning” indicates an action or procedure which, if not performed correctly, can result in injury
or a safety hazard. Comply strictly with the instructions and proceed with care.
"Caution!
“Caution” indicates an action or procedure which, if not performed correctly, can result in incorrect
operation or destruction of the device. Comply strictly with the instructions.
!Note!
“Note” indicates an action or procedure which, if not performed correctly, can have an indirect
effect on operation or trigger an unexpected response on the part of the device.

Proline Promag 10 Identification
Endress+Hauser 7
2 Identification
2.1 Device designation
The flowmeter system consists of the following components:
• Promag 10 transmitter
• Promag W, Promag P or Promag H sensor
In the compact version, the transmitter and sensor form a mechanical unit; in the remote version
they are mounted separate from one another.
2.1.1 Nameplate of the transmitter
F06-10xxxxxx-18-06-xx-xx-000
Fig. 1: Nameplate specifications for the “Promag 10” transmitter (example)
1 Order code /serial number: see the specifications on the order confirmation for the meanings of the individual
letters and digits
2 Power supply, frequency: 11...40 V DC / 20...28 V AC, 50...60 Hz
Power consumption: 8 VA / 6 W
3 Additional information:
EPD/MSÜ: with empty pipe detection
4Outputsavailable:
I-OUT (HART): with current output (HART)
PULSE-OUT: with pulse/status output
5 Permitted ambient temperature range
6 Degree of protection
PROMAG 10
-20°C (-4°F) <Tamb<+60°C (+140°F)
Pat. US 5,323,156 5,479,007
Pat. US 4,382,387 4,704,908 5,351,554
IP67 / NEMA/Type 4X Order Code:
Ser.No.:
TAG No.:
10P1H-XXXXXXXXXXXX
12345678901
ABCDEFGHJKLMNPQRST
11-40VDC/20-28VAC
50-60Hz
I-OUT (HART), PULSE-OUT
8VA/6W
i
EPD/MSU
2
3
4
6
5
1

Identification Proline Promag 10
8Endress+Hauser
2.1.2 Nameplate of the sensor
F06-xxxxxxxx-18-05-xx-xx-000
Fig. 2: Nameplate specifications for the “Promag” sensor (example)
1 Order code / serial number: see the specifications on the order confirmation for the meanings of the individual
letters and digits
2 Calibration factor: 0.5328 / zero point: –5
3 Nominal diameter: DN 100 / nominal pressure: EN (DIN) 16 bar
4 Medium temperature range
5 Lining material: PTFE
6 Measuring electrode material: stainless steel 1.4435/316L
7 Permitted ambient temperature range
8 See “Maximum measured error” →Page 74
9 Additional information (examples):
– EPD/MSÜ: with empty pipe detection electrode
– R/B: with reference electrode
10 Degree of protection
11 Reserved for additional information on device version (approvals, certificates)
12 Flow direction
2.1.3 Nameplate of the connections
F06-10xxxxxx-18-05-xx-xx-002
Fig. 3: Nameplate specifications for the transmitter (example)
-20°C (-4°F)<Tamb<+60°C (+140°F) NEMA/Type4X
Pat. US 4,382,387 4,704,908 5,540,103
XXP1H-XXXXXXXXXXXX
0.5328/ 5-
–40 ...+130°C/–40 ...+265°F°C °F
PTFE
12345678901
ABCDEFGHJKLMNPQRST
DN100 DIN EN PN16/
EPD/MSÜ, R/B
TM:
Order Code:
Materials:
K-factor:
Ser.No.:
TAG No.:
PROMAG P
1
2
3
7
12
10
11
1.4435/316L
Electrodes:
0,5% CAL
4
5
6
8
9
24
+
25
–
26
+
27
–L1 (L+)
12
N (L–)
$
PULSE-OUT
fmax: 100 Hz
Passive: 30 VDC
250 mA
I-OUT (HART)
Active: 4...20 mA
RLmax. = 700 Ohm
HART
RLmin. = 250 Ohm
Supply /
Versorgung /
Tension
d’Alimentation
See operating manual
Betriebsanleitung beachten
Observer Manual d’Instruction
319740-0000

Proline Promag 10 Identification
Endress+Hauser 9
2.2 Certificates and approvals
The devices are designed according to good engineering practice to meet state-of-the-art safety
requirements, have been tested and left the factory in a condition in which they are safe to operate.
The devices comply with the applicable standards and regulations in accordance with EN 61010
“Protection Measures for Electrical Equipment for Measurement, Control, Regulation and
Laboratory Procedures” and with the EMC requirements of EN 61326/A1 (IEC 1326).
The measuring system described in these Operating Instructions thus complies with the statutory
requirements of the EC Directives. Endress+Hauser confirms successful testing of the device by
affixing to it the CE mark.
2.3 Registered trademarks
KALREZ®and VITON®
Registered trademarks of E.I. Du Pont de Nemours & Co., Wilmington, USA
TRI-CLAMP®
Registered trademark of Ladish & Co., Inc., Kenosha, USA
HART®
Registered trademark of the HART Communication Foundation, Austin, USA
ToF Tool - Fieldtool®Package, Fieldcheck®, Applicator®
Registered or registration-pending trademarks of Endress+Hauser Flowtec AG, Reinach, CH

Installation Proline Promag 10
10 Endress+Hauser
3 Installation
3.1 Incoming acceptance, transport, storage
3.1.1 Incoming acceptance
On receipt of the goods, check the following points:
• Check the packaging and the contents for damage.
• Check the shipment, make sure nothing is missing and that the scope of supply matches your
order.
3.1.2 Transport
Please note the following when unpacking or transporting to the measuring point:
• The devices must be transported in the container supplied.
• Do not remove the protective covers or caps on the process connections before installation. This
is particularly important in the case of sensors with PTFE linings.
Points to note for flanged devices
"Caution!
• The wooden covers mounted on the flanges before the device leaves the factory protect the linings
on the flanges during storage and transportation. Do not remove these covers until immediately
before the device is installed in the pipe.
• Flanged devices may not be lifted at the transmitter housing or at the connection housing of the
remote version when transporting.
Transporting flanged devices (DN
≤ 300)
Use carrier slings when transporting and put the slings around both process connections .
Avoid chains as these could damage the housing.
#Warning!
Risk of injury if the measuring device slips! The centre of gravity of the entire measuring device
might be higher than the points around which the slings are slung.
Therefore, when transporting, make sure that the device does not unintentionally turn or slip.
F06-xxxxxxxx-22-00-00-xx-002
Fig. 4: Transporting sensors with DN ≤ 300

Proline Promag 10 Installation
Endress+Hauser 11
Transporting flanged devices (DN > 300)
Use only the metal eyes on the flanges for transporting the device, lifting it and positioning the
sensor in the piping.
"Caution!
Do not attempt to lift the sensor with the tines of a fork-lift truck beneath the metal casing.
The casing would buckle and damage the internal magnetic coils.
F06-10Fxxxxx-22-xx-xx-xx-001
Fig. 5: Transporting sensors with DN > 300
3.1.3 Storage
Note the following points:
• Pack the measuring device in such a way as to protect it reliably against impact for storage (and
transportation).
The original packaging provides optimum protection.
• The storage temperature corresponds to the ambient temperature range of the transmitter and
sensor →Page 75.
• Do not remove the protective covers or caps on the process connections before installation. This
is particularly important in the case of sensors with PTFE linings.
• The measuring device must be protected against direct sunlight during storage in order to avoid
unacceptably high surface temperatures.
• Choose a storage location where moisture does not collect in the measuring device. This will help
prevent fungus and bacteria infestation which can damage the liner.

Installation Proline Promag 10
12 Endress+Hauser
3.2 Installation conditions
3.2.1 Dimensions
The dimensions and lengths of the sensor and transmitter can be found in the “Technical
Information” document for the device in question. This can be downloaded as a PDF file from
www.endress.com. A list of the “Technical Information” documents available is provided in Section
“Documentation” on Page 83.
3.2.2 Installation location
Entrained air or gas bubble formation in the measuring tube can result in an increase in measuring
errors.
Avoid the following installation locations in the pipe:
• Highest point of a pipeline. Risk of air accumulating!
• Directly upstream from a free pipe outlet in a vertical pipeline.
A0003202
Fig. 6: Installation location
Installation of pumps
Sensors may not be installed on the pump suction side. This precaution is to avoid low pressure and
the consequent risk of damage to the lining of the measuring tube. Information on the pressure
tightness of the measuring tube lining is provided on Page 78.
Pulsation dampers may be needed when using piston pumps, piston diaphragm pumps or hose
pumps. Information on the vibration and shock resistance of the measuring system is provided
on Page 75.
A0003203
Fig. 7: Installation of pumps
h 2xDN³

Proline Promag 10 Installation
Endress+Hauser 13
Partially filled pipes
Partially filled pipes with gradients necessitate a drain-type configuration.
The empty pipe detection function (EPD →Page 58) provides additional security in detecting
empty or partially filled pipes.
"Caution!
Risk of solids accumulating! Do not install the sensor at the lowest point in the drain. It is advisable
to install a cleaning valve.
A0003204
Fig. 8: Installation in partially filled pipes
Down pipes
Install a siphon or a vent valve downstream of the sensor in down pipes longer than 5 meters. This
precaution is to avoid low pressure and the consequent risk of damage to the lining of the measuring
tube. This measure also prevents the liquid current stopping in the pipe which could cause air locks.
Information on the pressure tightness of the measuring tube lining is provided on Page 78.
A0003205
Fig. 9: Installation measures for vertical pipes
1Ventvalve
2Pipesiphon
³5xDN
³2xDN
>5m
2
1

Installation Proline Promag 10
14 Endress+Hauser
3.2.3 Orientation
An optimum orientation helps avoid gas and air accumulations and deposits in the measuring tube.
However, Promag also offers the additional function of empty pipe detection for detecting partially
filled measuring tubes or if outgassing fluids or fluctuating operating pressures are present.
Vertical orientation
This is the ideal orientation for self-emptying piping systems and for use in conjunction with empty
pipe detection.
A0003206
Fig. 10: Vertical orientation
Horizontal orientation
The measuring electrode axis should be horizontal. This prevents brief insulation of the two
measuring electrodes by entrained air bubbles.
"Caution!
Empty pipe detection only works correctly with horizontal orientation if the transmitter housing is
facing upwards (→Fig. 10). Otherwise there is no guarantee that empty pipe detection will
respond if the measuring tube is only partially filled or empty.
A0003207
Fig. 11: Horizontal orientation
1 EPD electrode for empty pipe detection (not for Promag H, DN 2...4)
2 Measuring electrodes for signal detection
3 Reference electrode for potential equalisation (not for Promag H)
A
1
22
A
3

Proline Promag 10 Installation
Endress+Hauser 15
Inlet and outlet run
If possible, install the sensor well clear of assemblies such as valves, T-pieces, elbows, etc.
Note the following inlet and outlet runs to comply with measuring accuracy specifications:
• Inlet run: ≥5 x DN
•Outletrun:≥2 x DN
A0003210
Fig. 12: Inlet and outlet run
3.2.4 Vibrations
Secure the piping and the sensor if vibration is severe.
"Caution!
If vibrations are too severe, we recommend the sensor and transmitter be mounted separately.
Information on the permitted vibration and shock resistance is provided on Page 75.
A0003208
Fig. 13: Measures to prevent vibration of the measuring device
5xDN2xDN
>10m

Installation Proline Promag 10
16 Endress+Hauser
3.2.5 Foundations, supports
For nominal diameters DN ≥350, mount the sensor on a foundation of adequate load-bearing
strength.
"Caution!
Risk of damage!
Do not support the weight of the sensor at the metal casing. The casing would buckle and damage
the internal magnetic coils.
A0003209
Fig. 14: Correct support for large nominal diameters (DN ≥ 350)
3.2.6 Adapters
Suitable adapters to DIN EN 545 (double-flange reducers) can be used to install the sensor in larger-
diameter pipes.
The resultant increase in the rate of flow improves measuring accuracy with very slow-moving
fluids. The nomogram shown here can be used to calculate the pressure loss caused by reducers and
expanders.
!Note!
The nomogram only applies to liquids of viscosity similar to water.
1. Calculate the ratio of the diameters d/D.
2. From the nomogram read off the pressure loss as a function of flow velocity (downstream from
the reduction) and the d/D ratio.
A0003213
Fig. 15: Pressure loss due to adapters
100
10
0.5
d/D
[mbar]
0.6 0.7 0.8 0.9
1 m/s
2 m/s
3 m/s
4 m/s
5 m/s
6 m/s
7 m/s
8 m/s
1
D
d
max. 8°

Proline Promag 10 Installation
Endress+Hauser 17
3.2.7 Nominal diameter and flow rate
The diameter of the pipe and the flow rate determine the nominal diameter of the sensor. The
optimum flow velocity is between 2 and 3 m/s.
The velocity of flow (v), moreover, has to be matched to the physical properties of the fluid:
• v < 2 m/s: for abrasive fluids
• v > 2 m/s: for fluids producing build-up
!Note!
Flow velocity can be increased, if necessary, by reducing the nominal diameter of the sensor
→Page 16.
SI units Recommended flow rate
Diameter Promag W Promag P Promag H
[mm]
Min./max. full scale value
(v ≈0.3 or 10 m/s)
Min./max. full scale value
(v ≈0.3 or 10 m/s)
Min./max. full scale value
(v ≈0.3 or 10 m/s)
2 – – 0.06 ...1.8 dm3/min
4 – – 0.25 ...7 dm3/min
8 – – 1 ...30 dm3/min
15 – – 4 ...100 dm3/min
25 9...300 dm3/min 9...300 dm3/min 9...300 dm3/min
32 15...500 dm3/min 15...500 dm3/min 25...700 dm3/min
40 25...700 dm3/min 25...700 dm3/min 35...1100 dm3/min
50 35...1100 dm3/min 35...1100 dm3/min 60...2000 dm3/min
65 60...2000 dm3/min 60...2000 dm3/min 90...3000 dm3/min
80 90...3000 dm3/min 90...3000 dm3/min 145...4700 dm3/min
100 145...4700 dm3/min 145...4700 dm3/min 0.06 ...1.8 dm3/min
125 220...7500 dm3/min 220...7500 dm3/min –
150 20...600 m3/h 20...600 m3/h –
200 35...1100 m3/h 35...1100 m3/h –
250 55...1700 m3/h 55...1700 m3/h –
300 80...2400 m3/h 80...2400 m3/h –
350 110…3300 m3/h 110…3300 m3/h –
400 140…4200 m3/h 140…4200 m3/h –
450 180…5400 m3/h 180…5400 m3/h –
500 220…6600 m3/h 220…6600 m3/h –
600 310…9600 m3/h 310…9600 m3/h –
700 420...13500 m3/h – –
– 480...15000 m3/h – –
800 550...18000 m3/h – –
900 690...22500 m3/h – –
1000 850...28000 m3/h – –
- 950...30000 m3/h – –
1200 1250...40000 m3/h – –
– 1550...50000 m3/h – –
1400 1700...55000 m3/h – –
- 1950...60000 m3/h – –
1600 2200...70000 m3/h – –
- 2500…80000 m3/h – –
1800 2800…90000 m3/h – –
- 3300…100000 m3/h – –
2000 3400…110000 m3/h –

Installation Proline Promag 10
18 Endress+Hauser
US units Recommended flow rate
Diameter Promag W Promag P Promag H
[inch]
Min./max. full scale value
(v ≈0.3 or 10 m/s)
Min./max. full scale value
(v ≈0.3 or 10 m/s)
Min./max. full scale value
(v ≈0.3 or 10 m/s)
1 1/12" – – 0.015 ...0.5 gal/min
5/32" – – 0.07...2 gal/min
5/16" – – 0.25...8 gal/min
1/2" – – 1.0...27 gal/min
1" 2.5...80 gal/min 2.5...80 gal/min 2.5...65 gal/min
1 1/4" 4...130 gal/min 4...130 gal/min 7...190 gal/min
1 1/2" 7...190 gal/min 7...190 gal/min 10...300 gal/min
2" 10...300 gal/min 10...300 gal/min 16...500 gal/min
2 1/2" 16...500 gal/min 16...500 gal/min 24...800 gal/min
3" 24...800 gal/min 24...800 gal/min 40...1250 gal/min
4" 40...1250 gal/min 40...1250 gal/min 0.015 ...0.5 gal/min
5" 60...1950 gal/min 60...1950 gal/min –
6" 90...2650 gal/min 90...2650 gal/min –
8" 155...4850 gal/min 155...4850 gal/min –
10" 250...7500 gal/min 250...7500 gal/min –
12" 350...10600 gal/min 350...10600 gal/min –
14" 500...15000 gal/min 500...15000 gal/min –
16" 600...19000 gal/min 600...19000 gal/min –
18" 800...24000 gal/min 800...24000 gal/min –
20" 1000...30000 gal/min 1000...30000 gal/min –
24" 1400...44000 gal/min 1400...44000 gal/min –
28" 1900…60000 gal/min – –
30" 2150...67000 gal/min – –
32" 2450...80000 gal/min – –
36" 3100...100000 gal/min – –
40" 3800...125000 gal/min – –
42" 4200...135000 gal/min – –
48" 5500...175000 gal/min – –
54" 9...300 Mgal/d – –
– 10...340 Mgal/d – –
60" 12...380 Mgal/d – –
– 13...450 Mgal/d – –
66" 14...500 Mgal/d – –
72" 16...570 Mgal/d – –
78" 18…650 Mgal/d – –
– 20…700 Mgal/d –

Proline Promag 10 Installation
Endress+Hauser 19
3.2.8 Length of connecting cable
When mounting the remote version, please note the following to achieve correct measuring results:
• Fix cable run or lay in armoured conduit. Cable movements can falsify the measuring signal
especially in the case of low fluid conductivities.
• Route the cable well clear of electrical machines and switching elements.
• If necessary, ensure potential equalisation between sensor and transmitter.
• The permitted length of connecting cable Lmax is determined by the fluid conductivity
(→Fig. 16). A minimum conductivity of 50 µS/cm is needed for all fluids.
• When the empty pipe detection function is switched on (EPD →Page 58), the maximum
connecting cable length is 10 m.
A0003214
Fig. 16: Permitted lengths of connecting cable for remote version
Area marked grey = permitted range
Lmax = length of connecting cable in [m]
Fluid conductivity in [
µ S/cm]
200
100
50 100 200
[m]
[ S/cm]m
L
max
L
max
50

Installation Proline Promag 10
20 Endress+Hauser
3.3 Installation
3.3.1 Installing Promag W sensor
!Note!
Bolts, nuts, seals, etc. are not included in the scope of supply and must be supplied by the customer.
The sensor is designed for installation between the pipe flanges:
• Please pay particular attention to the torques required on Page 21 ff.
• You can find a description of how to install additional ground disks on Page 21.
F06-10Fxxxxx-17-05-xx-xx-000
Fig. 17: Mounting Promag W sensor
Seals
Comply with the following instructions when mounting seals:
• Hard rubber lining →Additional seals are always required!
• Polyurethane lining →Additional seals are recommended.
• For DIN flanges, use only seals acc. to EN 1514-1.
• Make sure that the seals do not protrude into the piping cross-section.
"Caution!
Risk of short-circuit! Do not use electrically conductive sealing compound such as graphite. An
electrically conductive layer can build up inside the measuring tube and short-circuit the measuring
signal.
Ground cable (25...2000)
• If necessary, special ground cables can be ordered as accessories for potential equalisation
→Page 60.
• Information on potential equalisation and detailed mounting instructions for using ground cables
can be found on Page 40 ff.