Endress+Hauser Proline Promass 80 Application guide

BA058D/06/en/12.05
71008478
Valid as of software version:
V 2.01.XX (device software)
Description of Device Functions
Proline Promass 80
Coriolis Mass Flow Measuring System
6
MASS FLOW VOLUME FLOW DENSITY TEMPERATURE
UNIT VOLUME
UNIT MASS FLOW UNIT MASS
COMMISSIONING
LANGUAGE
ASSIGN LINE 1
SUM
ASSIGN
TOTALIZER
ASSIGN CURRENT
OPERATION
MODE
ASSIGN STATUS
OUTPUT
ASSIGN STATUS
INPUT
TAG
NAME
ASSIGN
LF-CUTOFF
INSTALLATION
DIRECTION
K-FACTOR
ACTUAL SYSTEM
CONDITION
FAILSAFE MODE
SERIAL
NUMBER
SW-REV.
AMP.
ACCESS CODE
ASSIGN LINE 2
OVERFLOW
CURRENT SPAN
ASSIGN
FREQUENCY
ON-VALUE
AKTIVE LEVEL
TAG
DESCRIPTION
ON-VALUE
MEASURING
MODE
ZERO
POINT
PREVIOUS SYST.
CONDITION
SIMULATION
MEASURAND
SW-REV.-NO.
SENSOR
SENSOR
TYPE
I/O-MODUL
TYPE
SW-REV.
I/O-MODUL
UNIT
VOLUME FLOW
DEFINE PRIVATE
CODE
100% VALUE
LINE 1
100% VALUE
LINE 2
UNIT SUM
VALUE 0_4 mA VALUE 20 mA
END VALUE
FREQUENCY
OFF-VALUE
MIN. PULSE WIDTH
BUS ADDRESSE
OFF-VALUE
POSITVE ZERO
RETURN
NOMINAL
DIAMETER
ASSIGN SYSTEM
ERROR
VALUE
SIMULATION
STATUS ACCESS
VALUE F LOW
TIME CONSTANT
SIMULATION
STATUS
HART PROTOCOL
EPD
SYSTEM
DAMPING
SENSOR
TYPE
ERROR
CATEGORY
MEASURING
VALUES
SYSTEM UNITS
QUICK SETUP
OPERATION
USER INTERFACE
TOTALIZER
CURRENT
OUTPUT
PULSE/FREQ.-
OUTPUT
STATUS
OUTPUT
S TAT U S
INPUT
COMMUNICATION
PROCESS
PARAMETER
SYSTEM
PARAMETER
SENSOR DATA
SUPERVISION
SIMULATION SYST.
SENSOR VERSION
AMP. VERSION
MASS FLOW VOLUME FLOW DENSITY TEMPERATURE
UNIT VOLUME
UNIT MASS FLOW UNIT MASS
COMMISSIONING
LANGUAGE
ASSIGN LINE 1
SUM
ASSIGN
TOTALIZER
ASSIGN CURRENT
OPERATION
MODE
ASSIGN STATUS
OUTPUT
ASSIGN STATUS
INPUT
TAG
NAME
ASSIGN
LF-CUTOFF
INSTALLATION
DIRECTION
K-FACTOR
ACTUAL SYSTEM
CONDITION
FAILSAFE MODE
SERIAL
NUMBER
SW-REV.
AMP.
ACCESS CODE
ASSIGN LINE 2
OVERFLOW
CURRENT SPAN
ASSIGN
FREQUENCY
ON-VALUE
AKTIVE LEVEL
TAG
DESCRIPTION
ON-VALUE
MEASURING
MODE
ZERO
POINT
PREVIOUS SYST.
CONDITION
SIMULATION
MEASURAND
SW-REV.-NO.
SENSOR
SENSOR
TYPE
I/O-MODUL
TYPE
SW-REV.
I/O-MODUL
UNIT
VOLUME FLOW
DEFINE PRIVATE
CODE
100% VALUE
LINE 1
100% VALUE
LINE 2
UNIT SUM
VALUE 0_4 mA VALUE 20 mA
END VALUE
FREQUENCY
OFF-VALUE
MIN. PULSE WIDTH
BUS ADDRESSE
OFF-VALUE
POSITVE ZERO
RETURN
NOMINAL
DIAMETER
ASSIGN SYSTEM
ERROR
VALUE
SIMULATION
STATUS ACCESS
VALUE F LOW
TIME CONSTANT
SIMULATION
STATUS
HART PROTOCOL
EPD
SYSTEM
DAMPING
SENSOR
TYPE
ERROR
CATEGORY
MEASURING
VALUES
SYSTEM UNITS
QUICK SETUP
OPERATION
USER INTERFACE
TOTALIZER
CURRENT
OUTPUT
PULSE/FREQ.-
OUTPUT
STATUS
OUTPUT
STATUS
INPUT
COMMUNICATION
PROCESS
PARAMETER
SYSTEM
PARAMETER
SENSOR DATA
SUPERVISION
SIMULATION SYST.
SENSOR VERSION
AMP. VERSION
COMMISSIONING
LANGUAGE
ASSIGN LINE 1
SUM
ASSIGN
TOTALIZER
ASSIGN CURRENT
OPERATION
MODE
ASSIGN STATUS
OUTPUT
ASSIGN STATUS
INPUT
TAG
NAME
ASSIGN
LF-CUTOFF
INSTALLATION
DIRECTION
K-FACTOR
ACTUAL SYSTEM
CONDITION
FAILSAFE MODE
SERIAL
NUMBER
SW-REV.
AMP.
ACCESS CODE
ASSIGN LINE 2
O
CURRENT SPAN
ASSIGN
FREQUENCY
ON-VALUE
AKTIVE LEVEL
TAG
DESCRIPTION
ON-VALUE
MEASURING
MODE
ZERO
POINT
PREVIOUS SYST.
CONDITION
SIMULATION
MEASURAND
S
SENSOR
TYPE
I/O-MODUL
TYPE I
DEF
1
VA
E
F
O
MIN.
BUS
O
PO
D
ASS
S
QUICK SETUP
OPERATION
USER INTERFACE
TOTALIZER
CURRENT
OUTPUT
PULSE/FREQ.-
OUTPUT
STATUS
OUTPUT
STATUS
INPUT
COMMUNICATION
PROCESS
PARAMETER
SYSTEM
PARAMETER
SENSOR DATA
SUPERVISION
SIMULATION SYST.
SENSOR VERSION
AMP. VERSION

Device Functions Proline Promass 80
2Endress+Hauser

Device Functions Proline Promass 80 Table of Contents
Endress+Hauser 3
Table of Contents
1 Function matrix Promass 80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 The function matrix: layout and use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Group MEASURING VALUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Group SYSTEM UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Group QUICK SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5 Group OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Group USER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7 Group TOTALIZER 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8 Group HANDLING TOTALIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9 Group CURRENT OUTPUT 1/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
10 Group PULSE/FREQUENCY OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11 Group STATUS OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
11.1 Information on the response of the status output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
11.2 Switching action of the status output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
12 Group STATUS INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
13 Group COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
14 Group PROCESS PARAMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
15 Group SYSTEM PARAMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
16 Group SENSOR DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
17 Group SUPERVISION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
18 Group SIMULATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
19 Group SENSOR VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
21 Factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
21.1 SI units (not for USA and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
21.2 US units (only for USA and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Table of Contents Device Functions Proline Promass 80
4Endress+Hauser
Registered trademarks
HART®
Registered trademark of HART Communication Foundation, Austin, USA
HistoROM™, S-DAT®
Registered trademarks of Endress+Hauser Flowtec AG, Reinach, CH

Device Functions Proline Promass 80 1 Function matrix Promass 80
Endress+Hauser 5
1 Function matrix Promass 80
1.1 The function matrix: layout and use
The function matrix is a two-level construct: the groups form one level, functions the other. The
groups are the highest-level grouping of the control options for the measuring device. Each group
comprises a number of functions.
You select a group in order to access the individual functions for controlling or configuring the
measuring device.
You will find an overview of the groups in the table of contents on page 3 and in the graphical
representation of the function matrix on Page 6.
You will also find an overview of the functions on Page 6, complete with the page references of the
detailed function descriptions.
The descriptions of the individual functions start on Page 7.
Example of how to configure a function (in this case changing the language for the user interface):
mEntry into the function matrix (Fkey).
nSelect the OPERATION group.
oSelect the LANGUAGE function, change the setting from ENGLISH to DEUTSCH
with OS and save F(all texts displayed on the user interface appear in German).
pExit the function matrix (ESC > 3 seconds).
A0001142
>3s
-+E
Esc
E
E
E
E
E E E E E
–
+
+
Esc
–
+
Esc
–
+
Esc
–
E
m
n
o
p

1 Function matrix Promass 80 Device Functions Proline Promass 80
6Endress+Hauser
1.2 Graphical illustration of the function matrix
UNIT LENGTH
(P. 12)
ACTUAL FREQUENCY
(P. 34)
ZERO PT. ADJ. (P. 51)
DENSITY COEFF. C 1
(P. 58)
PERMANENT
STORAGE (P. 60)
UNIT TEMPERATURE
(P. 11)
TEST DISPLAY
(P. 19)
VALUE SIM. CURRENT
(P. 28)
FAILSAFE VALUE (P. 34)
VALUE SIM. PULSE
(P. 40)
FIXED REFERENCE
DENSITY (P. 51)
DENSITY COEFF. C 0
(P. 58)
OPERATION HOURS
(P. 60)
UNIT REF. DENSITY
(P. 11)
BACKLIGHT
(P. 19)
SIMULATION CURRENT
(P. 27)
FAILSAFE MODE
(P. 34)
SIMULATION PULSE
(P. 39)
EPD EXC. CURRENT
(P. 51)
CAL. COEFF. KD 2
(P. 57)
MAX. CARR. TEMP.
(P. 58)
SYSTEM RESET
(P. 60)
UNIT DENSITY
(P. 11)
CONTRAST LCD
(P. 19)
ACTUAL CURRENT
(P. 27)
TIME CONSTANT
(P. 34)
FAILSAFE MODE
(P. 39)
VALUE SIM. SW. PT.
(P. 42)
EPD RESP. TIME (P. 50)
CAL. COEFF. KD 1
(P. 57)
MIN. CARR. TEMP.
(P. 58)
ALARM DELAY (P. 60)
TEMPERATURE
(P. 7)
UNIT CORR. VOLUME
(P. 10)
DISPLAY DAMPING
(P. 19)
RESET TOTALIZERS
(P. 21)
FAILSAFE MODE
(P. 27)
OUTPUT SIGNAL
(P. 32)
OUTPUT SIGNAL
(P. 37)
SIMUL. SWITCH PT.
(P. 42)
DEVICE ID
(P. 48)
EPD VALUE HIGH
(P. 50)
PRESSURE
(P. 53)
TEMP. COEFF. KT
(P. 57)
MAX. MEAS. TEMP.
(P. 58)
ERROR CATEGORY
(P. 60)
REFERENCE DENSITY
(P. 7)
UNIT CORR. VOL.
FLOW (P. 10)
ACCESS CODE
COUNTER (P. 16)
FORMAT
(P. 18)
TOTALIZER MODE
(P. 21)
TIME CONSTANT
(P. 27)
VALUE F HIGH
(P. 30)
PULSE WIDTH
(P. 36)
ACTUAL STATUS
OUTPUT (P. 42)
VALUE SIM. STATUS
INPUT (P. 47)
MANUFACTURER ID
(P. 48)
EPD LOW VALUE
(P. 50)
PRESSURE MODE
(P. 52)
FLOW DAMP.
(P. 56)
TEMP. COEFF. KM 2
(P. 57)
MIN. MEAS. TEMP.
(P. 58)
ASSIGN PROC. ERR.
(P. 59)
SW REV. I/O MOD
(P. 62)
DENSITY
(P. 7)
UNIT VOLUME
(P. 9)
STATUS ACCESS
(P. 16)
100% VALUE
(P. 18)
UNIT TOTALIZ. (P. 21)
VALUE 20 mA
(P. 24)
VALUE F LOW
(P. 30)
PULSE VALUE (P. 36)
TIME CONSTANT
(P. 42)
SIMUL. STATUS INP.
(P. 46)
HART PROTOCOL
(P. 48)
EMPTY PIPE DET.
(P. 50)
RESTORE ORIG. (P. 52)
DENSITY DAMPING
(P. 56)
TEMP. COEFF. KM
(P. 57)
DENSITY COEFF. C 5
(P. 58)
ERROR CATEGORY
(P. 59)
I/O MODULE TYPE
(P. 62)
CORR.VOL.-FLOW
(P. 7)
UNIT. VOL. FLOW (P. 9)
DEFINE PRIVATE CODE
(P. 16)
100% VALUE
(P. 18)
OVERFLOW
(P. 20)
VALUE 0_4 mA
(P. 24)
END VALUE FREQ.
(P. 29)
ASSIGN PULSE (P. 35)
SWITCH-OFF POINT
(P. 41)
MIN. PULSE WIDTH
(P. 46)
BUS ADDRESS
(P. 48)
OFF POINT LF CUTOFF
(P. 49)
DENSITY ADJUST
(P. 52)
POS. ZERO RET.
(P. 55)
NOMINAL DIAMETER
(P. 57)
DENSITY COEFF. C 4
(P. 58)
ASSIGN SYS. ERR.
(P. 59)
VALUE SIM. MEAS.
(P. 61)
SW REV. S-DAT
(P. 62)
LANGUAGE GROUP
(P. 62)
VOLUME FLOW
(P. 7)
UNIT MASS
(P. 8)
ACCESS CODE
(P. 16)
ASSIGN LINE 2
(P. 17)
SUM
(P. 20)
FAILSAFE MODE
(P. 22)
CURRENT SPAN (P. 23)
ASSIGN FREQUENCY
(P. 29)
VALUE SIMUL. FREQ.
(P. 35)
SWITCH-ON POINT
(P. 41)
ACTIVE LEVEL
(P. 46)
TAG DESCR.
(P. 48)
ON POINT LF CUTOFF
(P. 49)
MEAS. FLUID
(P. 52)
MEASURING MODE
(P. 54)
ZERO POINT
(P. 57)
DENSITY COEFF. C 3
(P. 58)
PREV. SYST. COND.
(P. 59)
SIM. MEASURAND
(P. 61)
SENSOR TYPE
(P. 62)
SW REV. AMPLIF.
(P. 62)
MASS FLOW
(P. 7)
UNIT. MASS FLOW
(P. 8)
UNIT PRESSURE
(P. 12)
QS COMMISSION
(P. 13)
LANGUAGE
(P. 15)
ASSIGN LINE 1
(P. 17)
ASSIGN TOTALIZER
(P. 20)
RESET ALL TOTALIZERS
(P. 22)
ASSIGN CURRENT
OUTPUT (P. 23)
OPERATION MODE
(P. 29)
SIMULATION FREQ.
(P. 35)
ASSIGN STATUS
OUTPUT (P. 41)
ASSIGN STATUS
INPUT (P. 46)
TAG NAME
(P. 48)
ASSIGN LF CUTOFF
(P. 49)
DENSITY SET POINT
(P. 51)
INST. DIR. SENSOR
(P. 54)
K-FACTOR
(P. 57)
DENSITY COEFF. C 2
(P. 58)
ACT. SYST. COND.
(P. 59)
SIM. FAILSAFE (P. 61)
SERIAL NUMBER (P. 62)
DEVICE SOFTWARE
(P. 62)
⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒
MEASURING VALUES
(P. 7)
SYSTEM UNITS
(P. 8)
QUICK SETUP
(P. 13)
OPERATION
(P. 15)
USER INTERFACE
(P. 17)
TOTALIZER 1/2
(P. 20)
HANDLING TOTALIZER
(P. 22)
CURRENT OUTPUT 1/2
(P. 22)
PULS./FREQ. OUTP.
(P. 29)
STATUS OUTPUT
(P. 41)
STATUS INPUT (P. 46)
COMMUNICATION
(P. 48)
PROCESS PARAMETER
(P. 49)
SYSTEM PARAMETER
(P. 54)
SENSOR DATA (P. 57)
SUPERVISION (P. 59)
SIMULAT. SYSTEM
(P. 61)
SENSOR VERSION
(P. 62)
AMPLIFIER VERS.
(P. 62)

Device Functions Proline Promass 80 2 Group MEASURING VALUES
Endress+Hauser 7
2 Group MEASURING VALUES
Function description MEASURING VALUES
!Note!
• The engineering unit of the measured variable shown here can be set in the “SYSTEM UNITS” group (see Page 8).
• If the fluid in the pipe flows backwards, a negative sign prefixes the flow reading on the display.
MASS FLOW In this function, the currently measured mass flow appears on the display.
Display:
5-digit floating-point number, including unit and sign
(e.g. 462.87 kg/h; –731.63 lb/min; etc.)
VOLUME FLOW In this function, the currently measured volumetric flow appears on the display.
Display:
5-digit floating-point number, including unit and sign
(e.g. 5.5445 dm3/min; 1.4359 m3/h; –731.63 gal/d; etc.)
CORRECTED VOLUME
FLOW
The calculated corrected volume flow appears on the display. The calculated corrected
volume flow is derived from the measured mass flow and the reference density of the
fluid (density at reference temperature, measured or fixed entry).
Display:
5-digit floating-point number, including unit and sign
(e.g. 1.3549 Nm3/h; 7.9846 scm/day; etc.)
DENSITY In this function, the currently measured density or the specific gravity appears on the
display.
Display:
5-digit fixed-point number, including unit
(e.g. 1.2345 kg/dm3; 993.5 kg/dm3; etc.)
REFERENCE DENSITY The density of the fluid, at reference temperature, appears on the display. The reference
density can be calculated with the measured density or also specified via the function
FIXED REFERENCE DENSITY.
Display:
5 digit floating-point number, incl. unit corr. to 0.100000...6.00000 kg/dm3
(e.g. 1.2345 kg/dm3; 993.5 kg/m3; 1.0015 SG_20 °C; etc.)
TEMPERATURE In this function, the currently measured temperature appears on the display.
Display:
5-digit floating-point number, including unit and sign
(e.g. –23.4 °C; 160.0 °F; 295.4 K; etc.)

3 Group SYSTEM UNITS Device Functions Proline Promass 80
8Endress+Hauser
3 Group SYSTEM UNITS
Function description SYSTEM UNITS
You can select the unit for the measured variable in this function group.
UNIT MASS FLOW Use this function to select the unit for displaying the mass flow (mass/time).
The unit you select here is also valid for:
• Current output
• Frequency output
• Switching points (limit value for mass flow, flow direction)
• Low flow cut off
Options:
Metric:
gram →g/s; g/min; g/h; g/day
kilogram →kg/s; kg/min; kg/h; kg/day
Metric ton →t/s; t/min; t/h; t/day
US:
ounce →oz/s; oz/min; oz/h; oz/day
pound →lb/s; lb/min; lb/h; lb/day
ton →ton/s; ton/min; ton/h; ton/day
Factory setting:
Country dependent (kg/h or US lb/day)
UNIT MASS Use this function to select the unit for displaying the mass.
The unit you select here is also valid for:
• Pulse value (e.g. kg/p)
Options:
Metric →g; kg; t
US →oz; lb; ton
Factory setting:
Country dependent (kg or US lb)
!Note!
The unit for the totalizer is independent of your choice here, it is selected separately in
the TOTALIZER 1/2 function group (see Page 20).

Device Functions Proline Promass 80 3 Group SYSTEM UNITS
Endress+Hauser 9
UNIT VOLUME FLOW Use this function to select the unit for the volume flow.
The unit you select here is also valid for:
• Current output
• Frequency output
• Switching points (limit value for volume flow, flow direction)
• Low flow cut off
Options:
Metric:
Cubic centimeter →cm3/s; cm3/min; cm3/h; cm3/day
Cubic decimeter →dm3/s; dm3/min; dm3/h; dm3/day
Cubic meter →m3/s; m3/min; m3/h; m3/day
Milliliter →ml/s; ml/min; ml/h; ml/day
Liter →l/s; l/min; l/h; l/day
Hectoliter →hl/s; hl/min; hl/h; hl/day
Megaliter →Ml/s; Ml/min; Ml/h; Ml/day
US:
Cubic centimeter →cc/s; cc/min; cc/h; cc/day
Acre foot →af/s; af/min; af/h; af/day
Cubic foot →ft3/s; ft3/min; ft3/h; ft3/day
Fluid ounce →oz f/s; oz f/min; oz f/h; oz f/day
Gallon →gal/s; gal/min; gal/h; gal/day
Kilo gallon →Kgal/s; Kgal/min; Kgal/h; Kgal/day
Million gallon →Mgal/s; Mgal/min; Mgal/h; Mgal/day
Barrel (normal fluids: 31.5 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Barrel (beer: 31.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Barrel (petrochemicals: 42.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Barrel (filling tanks: 55.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Imperial:
Gallon →gal/s; gal/min; gal/h; gal/day
Mega gallon →Mgal/s; Mgal/min; Mgal/h; Mgal/day
Barrel (beer: 36.0 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Barrel (petrochemicals: 34.97 gal/bbl) →bbl/s; bbl/min; bbl/h; bbl/day
Factory setting:
Country dependent (m3/h or US Mgal/day)
UNIT VOLUME Use this function to select the unit for the volume.
The unit you select here is also valid for:
• Pulse value (e.g. m3/p)
Options:
Metric →cm3; dm3; m3; ml; l; hl; Ml
US →cc; af; ft3; oz f; gal; Kgal; Mgal; bbl (normal fluids); bbl (beer);
bbl (petrochemicals); bbl (filling tanks)
Imperial →gal; Mgal; bbl (beer); bbl (petrochemicals)
Factory setting:
Country dependent (m3or US Mgal)
!Note!
The unit for the totalizer is independent of your choice here, it is selected separately in
the TOTALIZER 1/2 function group (see Page 20).
Function description SYSTEM UNITS

3 Group SYSTEM UNITS Device Functions Proline Promass 80
10 Endress+Hauser
UNIT CORRECTED
VOLUME FLOW
Use this function to select the unit for displaying the corrected volume flow (corrected
volume/time).
The unit you select here is also valid for:
• Current outputs
• Frequency outputs
• Relay switch points (limit value for corrected volume flow, flow direction)
• Low flow cut off
Options:
Metric:
Nl/s
Nl/min
Nl/h
Nl/day
Nm3/s
Nm3/min
Nm3/h
Nm3/day
US:
Sm3/s;
Sm3/min;
Sm3/h;
Sm3/day
Scf/s;
Scf/min;
Scf/h;
Scf/day
Factory setting:
Nm3/h
UNIT CORR. VOLUME Use this function to select the unit for displaying the corrected volume.
The unit you select here is also valid for:
• Pulse value (e.g. Nm3/p)
Options:
Metric:
Nm3
Nl
US:
Sm3
Scf
Factory setting:
Nm3
!Note!
The unit of the totalizers is independent of your choice here. The unit for each totalizer is
selected separately for the totalizer in question.
Function description SYSTEM UNITS