Endress+Hauser Proline Promag 10 Technical specifications

Products Solutions Services
KA00032D/06/EN/18.16
71321446
Brief Operating Instructions
Proline Promag 10
Electromagnetic flowmeter
These Brief Operating Instructions are not intended to replace
the Operating Instructions provided in the scope of supply.
Detailed information is provided in the Operating Instructions
and the additional documentation on the CD-ROM supplied.
The complete device documentation consists of:
• These Brief Operating Instructions
• Depending on the device version:
– Operating Instructions and the Description of Device Funct.
– Approvals and safety certificates
– Special safety instructions in accordance with the approvals
for the device (e.g. explosion protection, pressure
equipment directive etc.)
– Additional device-specific information

Proline Promag 10 Table of contents
Endress+Hauser 3
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Installation, commissioning and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 Safety conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Transporting to the measuring point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Installing the Promag E sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4 Installing the Promag H sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.5 Installing the Promag L sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.6 Installing the Promag P sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.7 Installing the Promag W sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.8 Installing the transmitter housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.9 Post-installation check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
3.1 Connecting the various housing types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.2 Connecting the remote version connecting cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.3 Potential equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.4 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
3.5 Post-connection check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
4.1 Switching on the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.3 Navigating within the function matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.4 Device functions to be configured during commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Safety instructions Proline Promag 10
4Endress+Hauser
1 Safety instructions
1.1 Designated use
• The measuring device is to be used only for measuring the flow of conductive liquids in closed
pipes. Most liquids can be measured as of a minimum conductivity of 50 S/cm.
• Any use other than that described here compromises the safety of persons and the entire
measuring system and is, therefore, not permitted.
• The manufacturer is not liable for damage caused by improper or non-designated use.
1.2 Installation, commissioning and operation
• The measuring device must only be installed, connected, commissioned and maintained by
qualified and authorized specialists (e.g. electrical technicians) in full compliance with the
instructions in these Brief Operating Instructions, the applicable norms, legal regulations and
certificates (depending on the application).
• The specialists must have read and understood these Brief Operating Instructions and must
follow the instructions they contain. If you are unclear on anything in these Brief Operating
Instructions, you must read the Operating Instructions (on the CD-ROM). The Operating
Instructions provide detailed information on the measuring device.
• The measuring device should only be installed in the pipe in a de-energized state free from
outside loads or strain.
• The measuring device may only be modified if such work is expressly permitted in the
Operating Instructions (on the CD-ROM).
• Repairs may only be performed if a genuine spare parts kit is available and this repair work is
expressly permitted.
• If performing welding work on the piping, the welding unit may not be grounded by means of
the measuring device.
1.3 Operational safety
• The measuring device is designed to meet state-of-the-art safety requirements, has been
tested, and left the factory in a condition in which it is safe to operate. Relevant regulations
and European standards have been observed.
• The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser distributor will supply you with current information and updates to these
Operating Instructions.
• The information specified on the warning notices, nameplates and connection labels fitted on
the measuring device must be observed. These contain important data, including information
on the permitted operating conditions, the application of the measuring device and data on
materials.
• If the measuring device is not operated at atmospheric temperatures, compliance with the
relevant basic conditions specified in the device documentation provided (on the CD-ROM) is
absolutely essential

Proline Promag 10 Safety instructions
Endress+Hauser 5
• The measuring device must be wired in accordance with the wiring diagrams and connection
labels. Interconnecting must be permitted.
• All parts of the measuring device must be integrated into the potential matching system of
the plant.
• The cables, tested cable glands and tested dummy plugs must suit the prevailing operating
conditions, e.g. the temperature range of the process. Housing openings that are not used
need to be sealed with dummy plugs.
• The measuring device can only be used in conjunction with fluids to which all the wetted parts
of the measuring device are adequately resistant. With regard to special fluids, including
fluids used for cleaning, Endress+Hauser will be happy to assist in clarifying the
corrosion-resistant properties of wetted materials. However, minor changes in temperature,
concentration or in the degree of contamination in the process may result in variations in
corrosion resistance. For this reason, Endress+Hauser does not accept any responsibility with
regard to the corrosion resistance of wetted materials in a specific application. The user is
responsible for the choice of suitable wetted materials in the process.
• When hot fluid passes through the measuring tube, the surface temperature of the housing
increases. In the case of the sensor, in particular, users should expect temperatures that can
be close to the fluid temperature. If the temperature of the fluid is high, implement sufficient
measures to prevent burning or scalding.
• Hazardous areas
Measuring devices for use in hazardous areas are labeled accordingly on the nameplate.
Relevant national regulations must be observed when operating the device in hazardous
areas.
• Hygienic applications
Measuring devices for hygienic applications have their own special labeling. Relevant national
regulations must be observed when using these devices.
• Pressure instruments
Measuring devices for use in systems that need to be monitored are labeled accordingly on the
nameplate. Relevant national regulations must be observed when using these devices. The
documentation on the CD-ROM for pressure instruments in systems that need to be
monitored is an integral part of the entire device documentation. The installation regulations,
connection data and safety instructions provided in the Ex documentation must be observed.
• Endress+Hauser will be happy to assist in clarifying any questions on approvals, their
application and implementation.

Safety instructions Proline Promag 10
6Endress+Hauser
1.4 Safety conventions
#Warning!
"Warning" indicates an action or procedure which, if not performed correctly, can result in injury
or a safety hazard. Comply strictly with the instructions and proceed with care.
"Caution!
"Caution" indicates an action or procedure which, if not performed correctly, can result in
incorrect operation or destruction of the device. Comply strictly with the instructions.
Note! "Note" indicates an action or procedure which, if not performed correctly, can have an
indirect effect on operation or trigger an unexpected response on the part of the device.

Proline Promag 10 Installation
Endress+Hauser 7
2 Installation
2.1 Transporting to the measuring point
• Transport the measuring device to the measuring point in the original packaging.
• Do not remove the covers or caps until immediately before installation.
2.1.1 Transporting flanged devices DN 300 (12")
2.1.2 Transporting flanged devices DN > 300 (12")
Use only the metal eyes provided on the flanges to transport, lift or position the sensor in the
piping.
"Caution!
Do not attempt to lift the sensor with the tines of a fork-lift truck beneath the metal casing!
This would buckle the casing and damage the internal magnetic coils.
A0008153
A0008978
To transport the unit, use slings slung around the
process connections or use lugs (if available).
#Warning!
Risk of injury! The device can slip.
The center of gravity of the measuring device may be
higher than the holding points of the slings.
Always ensure that the device cannot slip or turn
around its axis.
A0008979
Do not lift measuring devices by the transmitter
housing or the connection housing in the case of the
remote version. Do not use chains as they could
damage the housing.

Installation Proline Promag 10
8Endress+Hauser
2.2 Installation conditions
2.2.1 Dimensions
For the dimensions of the measuring device, see the associated Technical Information on the
CD-ROM.
2.2.2 Mounting location
The accumulation of air or formation of gas bubbles in the measuring tube can result in an
increase in measuring errors. For this reason avoid the following mounting locations in the
pipe:
• At the highest point of a pipeline. Risk of air accumulating!
• Directly upstream from a free pipe outlet in a down pipe.
A0008154
Installation of pumps
Do not install the sensor on the intake side of a pump. This precaution is to avoid low pressure
and the consequent risk of damage to the lining of the measuring tube. It might be necessary to
use pulse dampers in systems incorporating piston pumps, piston diaphragm pumps or
peristaltic pumps.
Information on the measuring system's pressure tightness and resistance to vibration and shock
can be found in the Operating Instructions of the CD-ROM.
A0003203
h 2xDN³

Proline Promag 10 Installation
Endress+Hauser 9
Partially filled pipes
Partially filled pipes with gradients necessitate a drain-type configuration.
The empty pipe detection (EPD) function offers additional protection by detecting empty or
partially filled pipes.
"Caution!
Risk of solids accumulating! Do not install the sensor at the lowest point in the drain. It is
advisable to install a cleaning valve.
Down pipes
Install a siphon or a vent valve downstream of the sensor in down pipes longer than 5 m (16 ft).
This precaution is to avoid low pressure and the consequent risk of damage to the lining of the
measuring tube. This measure also prevents the system losing prime, which could cause air
pockets.
For information on the pressure tightness of the measuring tube lining, see the Operating
Instructions on the CD-ROM.
A0008155
Installation in a partially filled pipe
A0008157
Measures for installation in a down pipe,
h > 5 m (16 ft)
1. Vent valve
2. Siphon
5 x DN
2 x DN
³
³
h
2
1

Installation Proline Promag 10
10 Endress+Hauser
2.2.3 Orientation
An optimum orientation helps avoid gas and air accumulations and buildup in the measuring
tube. The measuring device, nevertheless, supplies a range of functions and tools to measure
problematic fluids correctly:
• Electrode cleaning circuitry (ECC) to prevent electrically conductive deposits in the measuring
tube, e.g. for fluids causing buildup
• Empty pipe detection (EPD) for detecting partially filled measuring tubes, e.g. in the case of
degassing fluids or varying process pressures
• Exchangeable measuring electrodes for abrasive fluids (only Promag W)
Vertical orientation
Horizontal orientation
The measuring electrode plane should be horizontal. This prevents brief insulation of the two
electrodes by entrained air bubbles.
"Caution!
In the case of horizontal orientation, empty pipe detection only works correctly if the transmitter
housing is facing upwards. Otherwise there is no guarantee that empty pipe detection will
respond if the measuring tube is only partially filled or empty.
A0008158
This orientation is optimum for self-emptying piping
systems and when using empty pipe detection (EPD)
or open electrode detection (OED).
A0008159
1. EPD electrode for empty pipe detection
(not for Promag H, DN 2 to 15, 1/12 to ½").
2. Measuring electrodes for signal detection
3. Reference electrode for potential equalization
(not for Promag H)
A1
22
A
3

Proline Promag 10 Installation
Endress+Hauser 11
Inlet and outlet runs
If possible, install the sensor upstream from fittings such as valves, T-pieces, elbows, etc.
2.2.4 Vibrations
Secure and fix both the piping and the sensor if vibrations are severe.
A0008160
The following inlet and outlet runs must be observed
in order to meet accuracy specifications:
• Inlet run: 5 × DN
•Outletrun:2 × DN
A0008161
Measures to prevent device vibration,
L > 10 m (33 ft)
"Caution!
It is advisable to install the sensor and transmitter
separately if vibration is excessively severe. For
information on the permitted shock and vibration
resistance , see the Operating Instructions on the
CD-ROM.
5xDN³³2xDN
L

Installation Proline Promag 10
12 Endress+Hauser
2.2.5 Foundations, supports
If the nominal diameter is DN 350 (14"), mount the sensor on a foundation of adequate
load-bearing strength.
"Caution!
Risk of damage! Do not support the weight of the sensor on the metal casing.
This would buckle the casing and damage the internal magnetic coils.
A0008163
2.2.6 Length of connecting cable
Comply with the following instructions in order to ensure correct measuring results:
• Secure the cable run or route the cable in an armored conduit. Movement of the cable can
falsify the measuring signal, particularly if the fluid conductivity is low.
• Route the cable well clear of electrical machines and switching elements.
• Ensure potential equalization between the sensor and transmitter, if necessary.
• The permissible cable length Lmax depends on the fluid conductivity.
A0008981
Gray shaded area =
permissible range
Lmax = length of connecting
cable in [m]/[ft]
Fluid conductivity in [S/cm]
Lmax
[ S/cm]m
200
100
50
Lmax
50 100 200
[m]
[ft]
200 6000 400
Lmax
[ft]
200 6000 400

Proline Promag 10 Installation
Endress+Hauser 13
2.3 Installing the Promag E sensor
"Caution!
• The plates mounted on the two sensor flanges protect the PTFE which is turned over the
flanges and, consequently, should not be removed until immediately prior to mounting the
sensor.
• The protective plates must always remain mounted while the device is in storage.
• Make sure that the lining at the flange is not damaged or removed.
2.3.1 Seals
Comply with the following instructions when installing seals:
•No seals are required for PFTE measuring tube lining.
• For DIN flanges, only use seals to DIN EN 1514-1.
• Make sure that the mounted seals do not protrude into the piping cross-section.
"Caution!
Risk of short circuit! Do not use electrically conductive sealing compounds such as graphite! An
electrically conductive layer could form on the inside of the measuring tube and short-circuit the
measuring signal.
2.3.2 Ground cable
If necessary, special ground cables can be ordered as accessories for potential equalization.
2.3.3 Screw tightening torques (Promag E)
Please note the following:
• The tightening torques listed below are for lubricated threads only.
• Always tighten the screws uniformly and in diagonally opposite sequence.
• Overtightening the screws will deform the sealing faces or damage the seals.
• The tightening torques listed below apply only to pipes not subjected to tensile stress.
a0008165
Note!
Screws, nuts, seals, etc. are not included in the
scope of supply and must be supplied by the
customer.
The sensor is installed between the two pipe flanges:
• The requisite torques must be observed ä14
• If grounding disks are used, follow the mounting
instructions which will be enclosed with the
shipment

Installation Proline Promag 10
14 Endress+Hauser
Promag E tightening torques for EN (DIN)
Nominal diameter
[mm]
EN (DIN)
Pressure rating [bar]
Threaded
fasteners
Max. tightening torque
[Nm]
15 PN 40 4 × M 12 11
25 PN 40 4 × M 12 26
32 PN 40 4 × M 16 41
40 PN 40 4 × M 16 52
50 PN 40 4 × M 16 65
65 * PN 16 8 × M 16 43
80 PN 16 8 × M 16 53
100 PN 16 8 × M 16 57
125 PN 16 8 × M 16 75
150 PN 16 8 × M 20 99
200 PN 10 8 × M 20 141
200 PN 16 12 × M 20 94
250 PN 10 12 × M 20 110
250 PN 16 12 × M 24 131
300 PN 10 12 × M 20 125
300 PN 16 12 × M 24 179
350 PN 6 12 × M 20 200
350 PN 10 16 × M 20 188
350 PN 16 16 × M 24 254
400 PN 6 16 × M 20 166
400 PN 10 16 × M 24 260
400 PN 16 16 × M 27 330
450 PN 6 16 × M 20 202
450 PN 10 20 × M 24 235
450 PN 16 20 × M 27 300
500 PN 6 20 × M 20 176
500 PN 10 20 × M 24 265
500 PN 16 20 × M 30 448
600 PN 6 20 × M 24 242
600 PN 10 20 × M 27 345
600 * PN 16 20 × M 33 658
* Designed acc. to EN 1092-1 (not to DIN 2501)

Proline Promag 10 Installation
Endress+Hauser 15
Promag E tightening torques for ANSI
Promag E tightening torques for JIS
Nominal diameter ANSI Max. tightening torque
Pressure rating
[lbs]
Threaded
fasteners
PTFE
[mm] [inch] [Nm] [lbf · ft]
15 ½" Class 150 4 × ½" 6 4
25 1" Class 150 4 × ½" 11 8
40 1 ½" Class 150 4 × ½" 24 18
50 2" Class 150 4 × 5/8" 47 35
80 3" Class 150 4 × 5/8" 79 58
100 4" Class 150 8 × 5/8" 56 41
150 6" Class 150 8 × ¾" 106 78
200 8" Class 150 8 × ¾" 143 105
250 10" Class 150 12 × 7/8" 135 100
300 12" Class 150 12 × 7/8" 178 131
350 14" Class 150 12 × 1" 260 192
400 16" Class 150 16 × 1" 246 181
450 18" Class 150 16 × 1 1/8" 371 274
500 20" Class 150 20 × 1 1/8" 341 252
600 24" Class 150 20 × 1 ¼" 477 352
Nominal diameter JIS Max. tightening torque [Nm]
[mm] Pressure rating Threaded fasteners PTFE
15 20K 4 × M 16 16
25 20K 4 × M 16 32
32 20K 4 × M 16 38
40 20K 4 × M 16 41
50 10K 4 × M 16 54
65 10K 4 × M 16 74
80 10K 8 × M 16 38
100 10K 8 × M 16 47
125 10K 8 × M 20 80
150 10K 8 × M 20 99
200 10K 12 × M 20 82
250 10K 12 × M 22 133
300 10K 16 × M 22 99

Installation Proline Promag 10
16 Endress+Hauser
2.4 Installing the Promag H sensor
Depending on the order specifications, the sensor is supplied with or without ready-mounted
process connections. Mounted process connections are fixed to the sensor with 4 or 6
hexagonal-headed bolts.
"Caution!
Depending on the application and length of the pipe, the sensor may have to be supported or
additionally secured. The sensor must be secured if using plastic process connections. An
appropriate wall mounting kit can be ordered separately from Endress+Hauser as an accessory.
2.4.1 Seals
When mounting the process connections, make sure that the seals in question are free from dirt
and centered correctly.
"Caution!
• The screws must be securely tightened in the case of metal process connections. Together
with the sensor, the process connection forms a metal connection that ensures defined seal
compression.
• The seals should be replaced periodically depending on the application, particularly if molded
seals are used (aseptic version)! The intervals between seal replacement depend on the
frequency of the cleaning cycles and the fluid and cleaning temperatures. Replacement seals
can be ordered as an accessory.
2.4.2 Welding the sensor into the pipe (weld nipples)
"Caution!
Risk of destroying the electronics! Make sure that the welding system is not grounded via the
sensor or transmitter.
a. Secure the sensor with a few welding points in the pipe.
A welding jig suitable for this purpose can be ordered separately as an accessory.
b. Release the screws on the process connection flange and remove the sensor, including the
seal, from the pipe.
c. Weld the process connection into the pipe.
d. Mount the sensor back into the pipe.
In doing so, make sure the seals are clean and correctly positioned.
Note!
• When welding is performed correctly with thin-walled pipes carrying food, the seal is not
damaged by the heat even when it is mounted. It is recommended, however, to
disassemble the sensor and seal.
• For the disassembly work, it must be possible to open the pipe approx. 8 mm (0.31 in) in
total.

Proline Promag 10 Installation
Endress+Hauser 17
2.5 Installing the Promag L sensor
"Caution!
• The protective covers mounted on the two sensor flanges (DN 25 to 300 / 1 to 12") are used
to hold the lap joint flanges in place and to protect the PTFE liner during transportation.
Consequently, do not remove these covers until immediately before the sensor is installed in
the pipe.
• The protective plates must always remain mounted while the device is in storage.
• Make sure that the lining at the flange is not damaged or removed.
2.5.1 Seals
Comply with the following instructions when installing seals:
• Hard rubber lining additional seals are always required!
• Polyurethane lining no seals are required.
•No seals are required for PFTE measuring tube lining.
• For DIN flanges, only use seals to DIN EN 1514-1.
• Make sure that the mounted seals do not protrude into the piping cross-section.
"Caution!
Risk of short circuit!
Do not use electrically conductive sealing compounds such as graphite! An electrically
conductive layer could form on the inside of the measuring tube and short-circuit the measuring
signal.
2.5.2 Ground cable
If necessary, special ground cables can be ordered as accessories for potential equalization.
2.5.3 Screw tightening torques (Promag L)
Please note the following:
• The tightening torques listed below are for lubricated threads only.
• Always tighten the screws uniformly and in diagonally opposite sequence.
• Overtightening the screws will deform the sealing faces or damage the seals.
• The tightening torques listed below apply only to pipes not subjected to tensile stress.
a0008165
Note!
Screws, nuts, seals, etc. are not included in the
scope of supply and must be supplied by the
customer.
The sensor is installed between the two pipe flanges:
• The requisite torques must be observed ä18
• If grounding disks are used, follow the mounting
instructions which will be enclosed with the
shipment.
• To comply with the device specification, a
concentrical installation in the measuring section
is required

Installation Proline Promag 10
18 Endress+Hauser
Promag L tightening torques for EN (DIN)
Nominal diameter EN (DIN) Max. tightening torque
Hard rubber Polyurethane PTFE
[mm] Pressure rating
[bar]
Threaded
fasteners
[Nm] [Nm] [Nm]
25 PN 10/16 4 × M 12 - 6 11
32 PN 10/16 4 × M 16 - 16 27
40 PN 10/16 4 × M 16 - 16 29
50 PN 10/16 4 × M 16 - 15 40
65* PN 10/16 8 × M 16 - 10 22
80 PN 10/16 8 × M 16 - 15 30
100 PN 10/16 8 × M 16 - 20 42
125 PN 10/16 8 × M 16 - 30 55
150 PN 10/16 8 × M 20 - 50 90
200 PN 16 12 × M 20 - 65 87
250 PN 16 12 × M 24 - 126 151
300 PN 16 12 × M 24 - 139 177
350 PN 6 12 × M 20 111 120 -
350 PN 10 16 × M 20 112 118 -
400 PN 6 16 × M 20 90 98 -
400 PN 10 16 × M 24 151 167 -
450 PN 6 16 × M 20 112 126 -
450 PN 10 20 × M 24 153 133 -
500 PN 6 20 × M 20 119 123 -
500 PN 10 20 × M 24 155 171 -
600 PN 6 20 × M 24 139 147 -
600 PN 10 20 × M 27 206 219 -
700 PN 6 24 × M 24 148 139 -
700 PN 10 24 × M 27 246 246 -
800 PN 6 24 × M 27 206 182 -
800 PN 10 24 × M 30 331 316 -
900 PN 6 24 × M 27 230 637 -
900 PN 10 28 × M 30 316 307 -
1000 PN 6 28 × M 27 218 208 -
1000 PN 10 28 × M 33 402 405 -
1200 PN 6 32 × M 30 319 299 -
1200 PN 10 32 × M 36 564 568 -
1400 PN 6 36 × M 33 430 - -
1400 PN 10 36 × M 39 654 - -
1400 PN 16 36 × M 45 729 - -
1600 PN 6 40 × M 33 440 - -
1600 PN 10 40 × M 45 946 - -
1600 PN 16 40 × M 52 1007 - -
1800 PN 6 44 × M 36 547 - -
1800 PN 10 44 × M 45 961 - -

Proline Promag 10 Installation
Endress+Hauser 19
Promag L tightening torques for ANSI
1800 PN 16 44 × M 52 1108 - -
2000 PN 6 48 × M 39 629 - -
2000 PN 10 48 × M 45 1047 - -
2000 PN 16 48 × M 56 1324 - -
2200 PN 6 52 × M 39 698 - -
2200 PN 10 52 × M 52 1217 - -
2400 PN 6 56 × M 39 768 - -
2400 PN 10 56 × M 52 1229 - -
* Designed acc. to EN 1092-1 (not to DIN 2501)
Nominal dia-
meter
ANSI Threaded
fasteners
Max. tightening torque
Pressure
rating
Hard rubber Polyurethane PTFE
[mm] [inch] [lbs] [Nm] [lbf · ft] [Nm] [lbf · ft] [Nm] [lbf · ft]
25 1 Class 150 4 × 5/8" - - 5 4 14 13
40 1 ½ Class 150 4 × 5/8" - - 10 7 21 15
50 2" Class 150 4 × 5/8" - - 15 11 40 29
80 3" Class 150 4 × 5/8" - - 25 18 65 48
100 4" Class 150 8 × 5/8" - - 20 15 44 32
150 6" Class 150 8 × ¾" - - 45 33 90 66
200 8" Class 150 8 × ¾" - - 65 48 87 64
250 10" Class 150 12 × 7/8" - - 126 93 151 112
300 12" Class 150 12 × 7/8" - - 146 108 177 131
350 14" Class 150 12 × 1" 135 100 158 117 - -
400 16" Class 150 16 × 1" 128 94 150 111 - -
450 18" Class 150 16 × 1 1/8" 204 150 234 173 - -
500 20" Class 150 20 × 1 1/8" 183 135 217 160 - -
600 24" Class 150 20 × 1 ¼" 268 198 307 226 - -
Nominal diameter EN (DIN) Max. tightening torque
Hard rubber Polyurethane PTFE
[mm] Pressure rating
[bar]
Threaded
fasteners
[Nm] [Nm] [Nm]

Installation Proline Promag 10
20 Endress+Hauser
Promag L tightening torques for AWWA
Promag L tightening torques for AS 2129
Nominal dia-
meter
AWWA Threaded
fasteners
Max. tightening torque
Pressure
rating
Hartgummi Polyurethane PTFE
[mm] [inch] [Nm] [lbf · ft] [Nm] [lbf · ft] [Nm] [lbf · ft]
700 28" Class D 28 × 1 ¼" 247 182 292 215 - -
750 30" Class D 28 × 1 ¼" 287 212 302 223 - -
800 32" Class D 28 × 1 ½" 394 291 422 311 - -
900 36" Class D 32 × 1 ½" 419 309 430 317 - -
1000 40" Class D 36 × 1 ½" 420 310 477 352 - -
1050 42" Class D 36 × 1 ½" 528 389 518 382 - -
1200 48" Class D 44 × 1 ½" 552 407 531 392 - -
135054"ClassD44×1¾"730538----
150060"ClassD52×1¾"758559----
165066"ClassD52×1¾"946698----
180072"ClassD60×1¾"975719----
200078"ClassD64×2"853629----
215084"ClassD64×2"931687----
230090"ClassD68×2¼"1048773----
Nominal
diameter
AS 2129 Threaded
fasteners
Max. tightening torque
Pressure
rating
Hard rubber Polyurethane PTFE
[mm] [Nm] [Nm] [Nm]
350 Table E 12 × M 24 203 - -
400 Table E 12 × M 24 226 - -
450 Table E 16 × M 24 226 - -
500 Table E 16 × M 24 271 - -
600 Table E 16 × M 30 439 - -
700 Table E 20 × M 30 355 - -
750 Table E 20 × M 30 559 - -
800 Table E 20 × M 30 631 - -
900 Table E 24 × M 30 627 - -
1000 Table E 24 × M 30 634 - -
1200 Table E 32 × M 30 727 - -