Endress+Hauser Proline Promag P 100 Technical specifications

Brief Operating Instructions
Proline Promass P 100
Coriolis Mass Flow Measuring System
These Instructions are Brief Operating Instructions; they do not replace the
Operating Instructions included in the scope of supply.
For detailed information, refer to the Operating Instructions and other
documentation on the CD-ROM provided or visit "www.endress.com/
deviceviewer".
KA01118D/06/EN/01.12
71185340

Table of contents Proline Promass P 100
2 Endress+Hauser
Table of contents
1 Document information ...................................... 3
1.1 Symbols used ................................................ 3
2 Basic safety instructions ...................................... 5
2.1 Requirements for the personnel ....................................... 5
2.2 Designated use ............................................... 5
2.3 Workplace safety .............................................. 6
2.4 Operational safety .............................................. 6
2.5 Product safety ................................................ 7
3 Product description ......................................... 7
3.1 Product design ............................................... 7
4 Incoming acceptance and product identification ..................... 9
4.1 Incoming acceptance ............................................ 9
4.2 Product identification ........................................... 10
5 Storage and transport ...................................... 11
5.1 Storage conditions ............................................. 11
5.2 Transporting the product .......................................... 11
6 Mounting ............................................... 13
6.1 Mounting requirements .......................................... 13
6.2 Mounting the measuring device ...................................... 19
6.3 Post-mounting check ............................................ 20
7 Electrical connection ....................................... 21
7.1 Connection conditions ........................................... 21
7.2 Connecting the measuring device ...................................... 26
7.3 Hardware settings ............................................. 28
7.4 Ensuring the degree of protection ...................................... 31
7.5 Post-connection check ........................................... 32
8 Operation options ......................................... 33
8.1 Structure and function of the operating menu ................................ 33
8.2 Access to the operating menu via the Web browser ............................. 33
8.3 Access to the operating menu via the operating tool ............................. 36
9 System integration ........................................ 39
10 Commissioning ........................................... 39
10.1 Function check .............................................. 39
10.2 Establishing a connection via FieldCare ................................... 40
10.3 Configuring the device address via software ................................. 40
10.4 Configuring the measuring device ..................................... 40
10.5 Defining the tag name ........................................... 40
10.6 Protecting settings from unauthorized access ................................ 41
11 Diagnostic information ...................................... 43

Proline Promass P 100 Document information
Endress+Hauser 3
1 Document information
1.1 Symbols used
1.1.1 Safety symbols
Symbol Meaning
DANGER
A0011189-EN
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in serious
or fatal injury.
WARNING
A0011190-EN
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in serious
or fatal injury.
CAUTION
A0011191-EN
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in minor
or medium injury.
NOTICE
A0011192-EN
NOTICE!
This symbol contains information on procedures and other facts which do not result in personal
injury.
1.1.2 Electrical symbols
Symbol Meaning
A0011197
Direct current
A terminal to which DC voltage is applied or through which direct current flows.
A0011198
Alternating current
A terminal to which alternating voltage is applied or through which alternating current flows.
A0017381
Direct current and alternating current
• A terminal to which alternating voltage or DC voltage is applied.
• A terminal through which alternating current or direct current flows.
)
A0011200
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.
*
A0011199
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.
A0011201
Equipotential connection
A connection that has to be connected to the plant grounding system: This may be a potential equalization
line or a star grounding system depending on national or company codes of practice.
1.1.3 Tool symbols
Symbol Meaning
A0011221
Allen key

Document information Proline Promass P 100
4 Endress+Hauser
A0011222
Open-ended wrench
1.1.4 Symbols for certain types of information
Symbol Meaning
A0011182
Allowed
Indicates procedures, processes or actions that are allowed.
A0011183
Preferred
Indicates procedures, processes or actions that are preferred.
A0011184
Forbidden
Indicates procedures, processes or actions that are forbidden.
A0011193
Tip
Indicates additional information.
A0011194
Reference to documentation
Refers to the corresponding device documentation.
A0011195
Reference to page
Refers to the corresponding page number.
A0011196
Reference to graphic
Refers to the corresponding graphic number and page number.
,… ,
Series of steps
ÃResult of a sequence of actions
1.1.5 Symbols in graphics
Symbol Meaning
1, 2, 3,... Item numbers
,… ,
Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
A0013441
Flow direction
-
A0011187
Hazardous area
Indicates a hazardous area.
.
A0011188
Safe area (non-hazardous area)
Indicates a non-hazardous area.

Proline Promass P 100 Basic safety instructions
Endress+Hauser 5
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel must fulfill the following requirements for its tasks:
►Trained, qualified specialists must have a relevant qualification for this specific function and
task
►Are authorized by the plant owner/operator
►Are familiar with federal/national regulations
►Before beginning work, the specialist staff must have read and understood the instructions in
the Operating Instructions and supplementary documentation as well as in the certificates
(depending on the application)
►Following instructions and basic conditions
2.2 Designated use
Application and fluids
The measuring device described in these Instructions is intended only for flow measurement of
liquids and gases. Depending on the version ordered, the measuring device can also measure
potentially explosive, flammable, poisonous and oxidizing fluids.
Observing the limit values specified in the "Technical data" and listed in the Operating
Instructions and supplementary documentation, the measuring device may be used for the
following measurements only:
►Measured process variables: mass flow, density, temperature
►Calculated process variables: volume flow, corrected volume flow, reference density
To ensure that the measuring device remains in proper condition for the operation time:
►Use the measuring device only for fluids against which the process-wetted materials are
adequately resistant.
►Observe the limit values in "Technical data".
Incorrect use
The manufacturer is not liable for damage caused by improper or non-designated use.
NOTICE
Danger of breakage of the measuring tube due to corrosive or abrasive fluids.
Housing breakage due to mechanical overload possible!
►Verify the compatibility of the process fluid with the measuring tube material.
►Ensure the resistance of all fluid-wetted materials in the process.
►Observe the specified maximum process pressure.
Verification for borderline cases:
►For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in
verifying the corrosion resistance of fluid-wetted materials, but does not accept any warranty
or liability.

Basic safety instructions Proline Promass P 100
6 Endress+Hauser
Residual risks
!WARNING
Danger of housing breaking due to measuring tube breakage!
►In the event of a measuring tube breakage for a device version without rupture disk it is
possible for the pressure loading capacity of the sensor housing to be exceeded. This can lead
to rupture or failure of the sensor housing.
External surface temperature of the transmitter can increase by 20 K due to power consumption
of internal electronical components. Hot process fluids passing through the measuring device
will further increase the surface temperature of the measuring device. Especially the surface of
the sensor can reach temperatures which are close to process temperature.
Possible burn hazard due to fluid temperatures!
►For elevated fluid temperature, ensure protection against contact to prevent burns.
2.3 Workplace safety
For work on and with the device:
►Wear the required personal protective equipment according to federal/national regulations.
For welding work on the piping:
►Do not ground the welding unit via the measuring device.
2.4 Operational safety
Risk of injury.
►Operate the device in proper technical condition and fail-safe condition only.
►The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
►If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability,
►Carry out repairs on the device only if they are expressly permitted.
►Observe federal/national regulations pertaining to repair of an electrical device.
►Use original spare parts and accessories from Endress+Hauser only.
Hazardous area
To eliminate a danger for persons or for the facility when the device is used in the hazardous
area (e.g. explosion protection, pressure vessel safety):
►Based on the nameplate, check whether the ordered device is permitted for the intended use
in the hazardous area.
►Observe the specifications in the separate supplementary documentation that is an integral
part of these Instructions.

Proline Promass P 100 Product description
Endress+Hauser 7
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which they
are safe to operate.
It fulfills general safety requirements and legal requirements. It also conforms to the EC directives
listed in the device-specific EC declaration of conformity. Endress+Hauser confirms this fact by
applying the CE mark.
3 Product description
3.1 Product design
2
3
4
1
A0017609
å 1 Important components of a measuring device
1Transmitter housing cover
2 Main electronics module for Modbus RS485
3 Transmitter housing
4 Sensor

Product description Proline Promass P 100
8 Endress+Hauser
In the case of the device version with Modbus RS485 intrinsically safe, the Safety Barrier
Promass 100 forms part of the scope of supply.
2
3
4
5
1
A0017257
å 2 Important components of a measuring device
1Transmitter housing cover
2 I/O electronics module for EtherNet/IP
3 Main electronics module
4 Transmitter housing
5 Sensor

Proline Promass P 100 Incoming acceptance and product identification
Endress+Hauser 9
4 Incoming acceptance and product identification
4.1 Incoming acceptance
A0015502
1
+
2
1
+
2
A0013843
A0013695
A0015502
A0013698
A0015502
A0013699

Incoming acceptance and product identification Proline Promass P 100
10 Endress+Hauser
A0015502
A0013697
If one of the conditions is not satisfied, contact your Endress+Hauser Sales Center.
4.2 Product identification
The following options are available for identification of the measuring device:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
•Enter serial numbers from nameplates in W@M Device Viewer
(www.endress.com/deviceviewer): All information about the measuring device is displayed.
For an overview of the scope of the Technical Documentation provided, refer to the following:
The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
Order code:
Ext. ord. cd.:
Ser. no.:
1
2
3
A0014053
å 3 Example of a nameplate
1Order code
2 Serial number (Ser. no.)
3 Extended order code (Ext. ord. cd.)
For detailed information about interpreting the nameplate specifications, refer to the
Operating Instructions for the device on the CD-ROM provided