Endress+Hauser Proline Promass E 200 User manual

Operating Instructions
Proline Promass E 200
HART
Coriolis mass flow measuring system
BA01027D/06/EN/13.11
71135098
Valid as of version
01.01.zz (Device software)

Proline Promass E 200 HART
2 Endress+Hauser
• Make sure the document is stored in a safe place such that it is always available when working
on or with the device.
• To avoid danger to individuals or the facility, read the "Basic safety instructions" section carefully,
as well as all other safety instructions in the document that are specific to working procedures.
• The manufacturer reserves the right to modify technical data in line with technological
developments without prior notice. Your Endress+Hauser sales center will supply you with current
information and updates to this manual.

Proline Promass E 200 HART Table of contents
Endress+Hauser 3
Table of contents
1 Document information ............... 5
1.1 Document function ....................... 5
1.2 Document conventions .................... 5
1.2.1 Safety symbols .................... 5
1.2.2 Electrical symbols .................. 5
1.2.3 Tool symbols ..................... 5
1.2.4 Symbols for certain types of information ... 6
1.2.5 Symbols in graphics ................. 6
1.3 Documentation ......................... 7
1.3.1 Standard documentation .............. 7
1.3.2 Supplementary device-dependent
documentation .................... 7
2 Basic safety instructions .............. 8
2.1 Requirements for the personnel .............. 8
2.2 Designated use .......................... 8
2.3 Workplace safety ........................ 9
2.4 Operational safety ........................ 9
2.5 Product safety .......................... 9
3 Product description ................ 10
3.1 Product design ......................... 10
3.2 Registered trademarks .................... 10
3.3 Patents .............................. 10
4 Incoming acceptance and product
identification ...................... 12
4.1 Incoming acceptance ..................... 12
4.2 Product identification .................... 13
4.2.1 Nameplates ...................... 13
5 Storage and transport ............... 15
5.1 Storage conditions ...................... 15
5.2 Transporting the product .................. 15
5.3 Packaging disposal ...................... 16
6 Mounting .......................... 17
6.1 Mounting requirements ................... 17
6.1.1 Mounting position ................. 17
6.1.2 Requirements from environment and
process ......................... 19
6.1.3 Special mounting instructions ......... 21
6.2 Mounting the measuring device ............. 21
6.2.1 Required tools .................... 21
6.2.2 Preparing the measuring device ........ 21
6.2.3 Mounting the measuring device ........ 22
6.2.4 Turning the transmitter housing ....... 22
6.2.5 Turning the display module ........... 22
6.3 Post-mounting check .................... 23
7 Electrical connection ............... 24
7.1 Preparing the measuring device for the electrical
connection ........................... 24
7.1.1 Required tools .................... 24
7.1.2 Requirements for connecting cable ...... 24
7.1.3 Preparing the measuring device ........ 24
7.2 Connecting the measuring device ............ 24
7.2.1 Connecting the signal cables .......... 25
7.2.2 Connecting to the supply unit ......... 26
7.3 Ensuring the degree of protection of the measuring
device ............................... 27
7.4 Post-connection check ................... 27
8 Operation options .................. 29
8.1 Overview of operation options .............. 29
8.2 Structure and function of the operating menu .... 30
8.2.1 Structure of the operating menu ....... 30
8.2.2 Operating philosophy ............... 31
8.3 Access to the operating menu via the local
display .............................. 32
8.3.1 Measured value display and operating
elements ....................... 32
8.3.2 Navigation view and operating elements .. 34
8.3.3 Editing view and operating elements .... 36
8.3.4 Opening the context menu ........... 38
8.3.5 Navigating and selecting from list ....... 39
8.3.6 Calling up help text ................ 39
8.3.7 Changing the parameters ............ 41
8.3.8 User roles and related access
authorization .................... 42
8.3.9 Disabling write protection via access
code .......................... 42
8.3.10 Enabling and disabling the keypad lock ... 42
8.4 Access to the operating menu via the operating
tool ................................ 44
8.4.1 Field Xpert SFX100 ................ 44
8.4.2 FieldCare ....................... 44
8.4.3 AMS Device Manager .............. 45
8.4.4 SIMATIC PDM ................... 45
8.4.5 Field Communicator 475 ............ 45
8.4.6 Connecting operating tools ........... 46
9 System integration ................. 48
9.1 Overview of device description files .......... 48
9.1.1 Current version data for the device ..... 48
9.1.2 Operating tools ................... 48
9.2 Measured values via HART protocol .......... 48
9.3 Other settings ......................... 49
10 Commissioning .................... 50
10.1 Function check ........................ 50
10.2 Switching on the measuring device ........... 50
10.3 Setting the operating language .............. 50

Table of contents Proline Promass E 200 HART
4 Endress+Hauser
10.4 Configuring the measuring device ............ 51
10.4.1 Selecting and setting the medium ...... 52
10.4.2 Configuring the current outputs ........ 54
10.4.3 Configuring the local display .......... 58
10.4.4 Configuring the output conditioning ..... 60
10.4.5 Configuring the low flow cut off ....... 63
10.4.6 Configuring the partial filled pipe
detection ....................... 64
10.5 Advanced settings ....................... 65
10.5.1 Defining the tag name .............. 66
10.5.2 Setting the system units ............. 66
10.5.3 Carrying out a sensor adjustment ....... 68
10.5.4 Configuring the totalizer ............. 69
10.5.5 Carry out additional display
configurations .................... 70
10.6 Configuration management ................ 71
10.7 Simulation ............................ 72
10.8 Protecting settings from unauthorized access .... 73
10.8.1 Write protection via access code ....... 73
10.8.2 Write protection via lock switch ....... 74
11 Operation ......................... 76
11.1 Adjusting the operating language ............ 76
11.2 Configuring the display ................... 76
11.3 Reading off measured values ............... 76
11.4 Adapting the measuring device to the process
conditions ............................ 77
11.5 Perform totalizer reset .................... 77
11.6 Show data logging ...................... 78
12 Diagnostics and troubleshooting ..... 80
12.1 General troubleshooting .................. 80
12.2 Diagnostic information on local display ........ 81
12.2.1 Diagnostic message ................ 81
12.2.2 Calling up remedial measures ......... 82
12.3 Diagnostic event in the operating tool ......... 83
12.4 Diagnostic list ......................... 83
12.5 Overview of diagnostic events .............. 84
12.5.1 Adapting event level ............... 84
12.5.2 Diagnostics for the sensor ............ 85
12.5.3 Diagnostics for the electronics ......... 85
12.5.4 Diagnostics for the configuration ....... 86
12.5.5 Diagnostics for the process ........... 86
12.6 Event logbook ......................... 87
12.6.1 Event history .................... 87
12.6.2 Filtering the event logbook ........... 88
12.6.3 Overview of information events ........ 88
12.7 Firmware history ....................... 89
13 Repair ............................. 90
13.1 General notes .......................... 90
13.2 Spare parts ............................ 90
13.3 Endress+Hauser services .................. 91
14 Maintenance ...................... 92
14.1 Maintenance tasks ...................... 92
14.1.1 Exterior cleaning .................. 92
14.1.2 Interior cleaning .................. 92
14.2 Measuring and test equipment .............. 92
14.3 Endress+Hauser services .................. 92
15 Return ............................ 93
16 Disposal ........................... 94
16.1 Removing the measuring device ............. 94
16.2 Disposing of the measuring device ........... 94
17 Technical data ..................... 95
17.1 Application ........................... 95
17.2 Function and system design ................ 95
17.3 Input ............................... 95
17.4 Output .............................. 96
17.5 Power supply .......................... 97
17.6 Performance characteristics ................ 98
17.7 Installation ........................... 100
17.8 Environment ......................... 100
17.9 Process ............................. 101
17.10 Mechanical construction ................. 103
17.11 Operability ........................... 105
17.12 Certificates and approvals ................ 106
17.13 Application packages .................... 107
17.14 Accessories .......................... 108
Index ................................. 109

Proline Promass E 200 HART Document information
Endress+Hauser 5
1 Document information
1.1 Document function
These Operating Instructions contain all the information that is required in various phases of the life
cycle of the device: from product identification, incoming acceptance and storage, to mounting,
connection, operation and commissioning through to troubleshooting, maintenance and disposal.
1.2 Document conventions
1.2.1 Safety symbols
Symbol Meaning
DANGER
A0011189-EN
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
A0011190-EN
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
A0011191-EN
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
A0011192-EN
NOTICE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Symbol Meaning
A0011197
Direct current
A terminal to which DC voltage is applied or through which direct current flows.
A0011198
Alternating current
A terminal to which alternating voltage (sine-wave) is applied or through which alternating current flows.
)
A0011200
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.
*
A0011199
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.
A0011201
Equipotential connection
A connection that has to be connected to the plant grounding system: This may be a potential equalization
line or a star grounding system depending on national or company codes of practice.
1.2.3 Tool symbols
Symbol Meaning
A0013442
Torx screwdriver
A0011220
Flat blade screwdriver

Document information Proline Promass E 200 HART
6 Endress+Hauser
Symbol Meaning
A0011219
Phillips head screwdriver
A0011221
Allen key
A0011222
Hexagon wrench
1.2.4 Symbols for certain types of information
Symbol Meaning
A0011182
Allowed
Indicates procedures, processes or actions that are allowed.
A0011183
Preferred
Indicates procedures, processes or actions that are preferred.
A0011184
Forbidden
Indicates procedures, processes or actions that are forbidden.
A0011193
Tip
Indicates additional information.
A0011194
Reference to documentation
Refers to the corresponding device documentation.
A0011195
Reference to page
Refers to the corresponding page number.
A0011196
Reference to graphic
Refers to the corresponding graphic number and page number.
,… ,
Series of steps
ÃResult of a sequence of actions
A0013562
Help in the event of a problem
1.2.5 Symbols in graphics
Symbol Meaning
1, 2, 3,... Item numbers
,… ,
Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
A0013441
Flow direction
-
A0011187
Hazardous area
Indicates a hazardous area.
.
A0011188
Safe area (non-hazardous area)
Indicates a non-hazardous area.

Proline Promass E 200 HART Document information
Endress+Hauser 7
1.3 Documentation
1.3.1 Standard documentation
Document type Purpose and content of the document
Technical Information Planning aid for your device
The document contains all the technical data on the device and provides an
overview of the accessories and other products that can be ordered for the device.
Brief Operating Instructions Guide that takes you quickly to the 1st measured value
The Brief Operating Instructions contain all the essential information from
incoming acceptance to initial commissioning.
Description of Device Parameters Reference for your parameters
The document provides a detailed explanation of each individual parameter of
the operating menu. The description is aimed at those who work with the device
over the entire life cycle and perform specific configurations.
The document types listed are available:
• On the CD supplied with the device
•In the Download Area of the Endress+Hauser Internet site: www.endress.com ® Download
1.3.2 Supplementary device-dependent documentation
If operating the device in SIL applications, hazardous areas or in accordance with the Pressure
Equipment Directive, comply strictly with the instructions in the supplementary documentation.
The supplementary documentation is an integral part of the device documentation.
Document type Device particularities and document content
Safety Instructions Operation in hazardous areas
The document contains all the necessary information for the safe operation of the
device in hazardous areas, and explains how the device can be identified as an
Ex system from the device nameplate.
Information on the Pressure Equipment
Directive
Operation in accordance with the Pressure Equipment Directive
The document contains all the necessary information for the safe operation of the
device when used in accordance with the Pressure Equipment Directive, and
explains how the device can be identified as pressure equipment from the device
nameplate.
Functional Safety Manual Operation in SIL applications
The document contains all the necessary information for the safe operation of the
device in SIL applications, such as settings and installation instructions.
Installation Instructions Ordered accessory
The Installation Instructions contain all the information needed to install the
ordered accessory or spare part.
The document types listed are available:
• On the CD supplied with the device
•In the Download Area of the Endress+Hauser Internet site: www.endress.com ® Download

Basic safety instructions Proline Promass E 200 HART
8 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill the following
requirements:
►Trained, qualified specialists must have a relevant qualification for this specific function and task
►Are authorized by the plant owner/operator
►Are familiar with federal/national regulations
►Before beginning work, the specialist staff must have read and understood the instructions in the
Operating Instructions and supplementary documentation as well as in the certificates
(depending on the application)
►Following instructions and basic conditions
The operating personnel must fulfill the following requirements:
►Being instructed and authorized according to the requirements of the task by the facility's owner-
operator
►Following the instructions in these Operating Instructions
2.2 Designated use
Application and fluids
The measuring device described in these Instructions is intended only for flow measurement of
liquids and gases. Depending on the version ordered, the measuring device can also measure
potentially explosive, flammable, poisonous and oxidizing fluids.
Observing the limit values specified in the "Technical data" and listed in the Operating Instructions
and supplementary documentation, the measuring device may be used for the following
measurements only:
►Measured process variables: mass flow, density, temperature
►Calculated process variables: volume flow, corrected volume flow, reference density
To ensure that the measuring device remains in proper condition for the operation time:
►Use the measuring device only for fluids against which the process-wetted materials are
adequately resistant.
►Observe the limit values in "Technical data".
Incorrect use
The manufacturer is not liable for damage caused by improper or non-designated use.
NOTICE
Danger of breakage of the measuring tube due to corrosive or abrasive fluids.
Housing breakage due to mechanical overload possible!
►Verify the compatibility of the process fluid with the measuring tube material.
►Ensure the resistance of all fluid-wetted materials in the process.
►Observe the specified maximum process pressure.
Verification for borderline cases:
►For special fluids and fluids for cleaning, Endress+Hauser is glad to provide assistance in verifying
the corrosion resistance of fluid-wetted materials, but does not accept any warranty or liability.
Residual risks
!WARNING
Danger of housing breaking due to measuring tube breakage!
►In the event of a measuring tube breakage for a device version without rupture disk it is possible
for the pressure loading capacity of the sensor housing to be exceeded. This can lead to rupture
or failure of the sensor housing.

Proline Promass E 200 HART Basic safety instructions
Endress+Hauser 9
External surface temperature of the transmitter can increase by 20 K due to power consumption of
internal electronical components. Hot process fluids passing through the measuring device will
further increase the surface temperature of the measuring device. Especially the surface of the sensor
can reach temperatures which are close to process temperature.
Possible burn hazard due to fluid temperatures!
►For elevated fluid temperature, ensure protection against contact to prevent burns.
2.3 Workplace safety
For work on and with the device:
►Wear the required personal protective equipment according to federal/national regulations.
For welding work on the piping:
►Do not ground the welding unit via the measuring device.
2.4 Operational safety
Risk of injury.
►Operate the device in proper technical condition and fail-safe condition only.
►The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable dangers.
►If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability,
►Carry out repairs on the device only if they are expressly permitted.
►Observe federal/national regulations pertaining to repair of an electrical device.
►Use original spare parts and accessories from Endress+Hauser only.
Hazardous area
To eliminate a danger for persons or for the facility when the device is used in the hazardous area
(e.g. explosion protection, pressure vessel safety):
►Based on the nameplate, check whether the ordered device is permitted for the intended use in
the hazardous area.
►Observe the specifications in the separate supplementary documentation that is an integral part
of these Instructions.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-of-
the-art safety requirements, has been tested, and left the factory in a condition in which they are
safe to operate.
It fulfills general safety requirements and legal requirements. It also conforms to the EC directives
listed in the device-specific EC declaration of conformity. Endress+Hauser confirms this fact by
applying the CE mark.

Product description Proline Promass E 200 HART
10 Endress+Hauser
3 Product description
3.1 Product design
1 2 345 6 78
9
+E
–
A0014056
å 1 Important components of a measuring device
1Electronics compartment cover
2 Display module
3 Main electronics module
4 Cable glands
5 Transmitter
6 I/O electronics module
7 Terminals (pluggable spring terminals)
8 Connection compartment cover
9 Sensor
3.2 Registered trademarks
HARTÒ
Registered trademark of the HART Communication Foundation, Austin, USA
TRI-CLAMP Ò
Registered trademark of Ladish & Co., Inc., Kenosha, USA
ApplicatorÒ, FieldCareÒ, Field XpertTM, HistoROMÒ
Registered or registration-pending trademarks of the Endress+Hauser Group
3.3 Patents
US patents EP patents
5,610,342 0 701 213
6,513,393 1 055 102
6,412,35 1 054 240
6,651,513 ---

Proline Promass E 200 HART Product description
Endress+Hauser 11
US patents EP patents
6,412,355 1 054 240
7,555,397 ---

Incoming acceptance and product identification Proline Promass E 200 HART
12 Endress+Hauser
4 Incoming acceptance and product identification
4.1 Incoming acceptance
A0015502
1
+
2
1
+
2
A0013843
Is the order code on the delivery note (1) identical to the order code on the product sticker (2)?
A0013695
A0015502
A0013698
Are the goods undamaged?
A0015502
i
i
DELIVERY NOTE
A0013699
Do the nameplate data match the ordering information on the delivery note?
A0015502
A0013697
Is the CD-ROM with the Technical Documentation and documents present?
If one of the conditions does not comply, contact your Endress+Hauser distributor.

Proline Promass E 200 HART Incoming acceptance and product identification
Endress+Hauser 13
4.2 Product identification
The following options are available for identification of the measuring device:
• Nameplate specifications
• Order code with breakdown of the device features on the delivery note
•Enter serial numbers from nameplates in W@M Device Viewer
(www.endress.com/deviceviewer): All information about the measuring device is displayed.
For an overview of the scope of the Technical Documentation provided, refer to the following:
•The chapters "Additional standard documentation on the device" (® ä 7) and "Supplementary
device-dependent documentation" (® ä 7)
•The W@M Device Viewer : Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
4.2.1 Nameplates
Transmitter
Order code:
Ext. ord. cd.:
Ser. no.:
Date:
i
i
Patents
322540-0001
1
2
345
6
7
8
9
10 11 12
14
15
16
17
13
A0013906
å 2 Example of a transmitter nameplate
1Manufacturing location
2 Name of the transmitter
3 Order code
4 Serial number (Ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Electrical connection data, e.g. available inputs and outputs, supply voltage
7 Type of cable glands
8 Permitted ambient temperature (Ta)
9 Firmware version (FW) and device revision (Dev.Rev.) from the factory
10 CE mark, C-Tick
11 Additional information about the transmitter version (certificates, approvals), e.g. SIL, PROFIBUS
12 Permitted temperature range for cable
13 Manufacturing date: year-month
14 Degree of protection: e.g. IP, NEMA
15 Approval information for explosion protection
16 Document number of safety-related supplementary documentation, e.g. Safety Instructions
17 2-D matrix code

Incoming acceptance and product identification Proline Promass E 200 HART
14 Endress+Hauser
Sensor
Date:
K-factor: Size:
Materials:
Tm:
Patents
i
p test =
i
Order code:
Ext. ord. cd.:
Ser. no.:
322541-0000
0044
12
1
2
3 4 5 6 7
13
8
9
10
14 15 16
17
18
20
19
11
A0013907
å 3 Example of a sensor nameplate
1 Manufacturing location
2 Name of the sensor
3 Order code
4 Serial number (Ser. no.)
5 Extended order code (Ext. ord. cd.)
6 Nominal diameter of the sensor
7 Test pressure of the sensor
8 Calibration factor
9 Flange nominal diameter/nominal pressure
10 Material of measuring tube and manifold
11 Fluid temperature range
12 CE mark, C-Tick
13 Additional information about the sensor version (certificates, approvals), e.g. EHEDG, 3-A
14 Manufacturing date: year-month
15 Flow direction
16 2-D matrix code
17 Degree of protection: e.g. IP, NEMA
18 Approval information for explosion protection and Pressure Equipment Directive
19 Permitted ambient temperature (Ta)
20 Document number of safety-related supplementary documentation, e.g. Safety Instructions
Order code
The measuring device is reordered using the order code.
Extended order code
• The device type (product root) and basic specifications (mandatory features) are always listed.
• Of the optional specifications (optional features), only the safety and approval-related
specifications are listed (e.g. LA). If other optional specifications are also ordered, these are
indicated collectively using the # placeholder symbol (e.g. #LA#).
• If the ordered optional specifications do not include any safety and approval-related
specifications, they are indicated by the + placeholder symbol (e.g. 8E2B50-ABCDE+).

Proline Promass E 200 HART Storage and transport
Endress+Hauser 15
5 Storage and transport
5.1 Storage conditions
Observe the following notes for storage:
• Store in the original packaging to ensure protection from shock.
• Do not remove protective covers or protective caps installed on process connections. They prevent
mechanical damage to the sealing surfaces and fouling in the measuring tube.
• Protect from direct sunlight to avoid unacceptably high surface temperatures.
•Storage temperature: –40 to +80 °C (–40 to +176 °F), preferable for +20 °C (+68 °F)
• Store in a dry and dust-free place.
• Do not store outdoors.
5.2 Transporting the product
!WARNING
Center of gravity of the measuring device is higher than the suspension points of the
webbing slings.
Risk of injury if the measuring device slips.
►Secure the measuring device from rotating or slipping.
►Observe the weight specified on the packaging (stick-on label).
►Observe the transport instructions on the stick-on label on the electronics compartment cover.
A0015606
Observe the following notes during transport:
• Transport the measuring device to the measuring point in the original packaging.
• Lifting gear
– Webbing slings: Do not use chains, as they could damage the housing.
– For wood crates, the floor structure enables these to be loaded lengthwise or broadside using a
forklift.
•For measuring device > DN 40 (1½ in): lift the measuring device using the webbing slings at the
process connections; do not lift at the transmitter housing.
• Do not remove protective covers or protective caps installed on process connections. They prevent
mechanical damage to the sealing surfaces and fouling in the measuring tube.

Storage and transport Proline Promass E 200 HART
16 Endress+Hauser
5.3 Packaging disposal
All packaging materials are environmentally friendly and 100% recyclable:
• Measuring device secondary packaging: polymer stretch film that conforms to EC Directive
2002/95/EC (RoHS).
• Packaging:
– Wood crate, treated in accordance with ISPM 15 standard, which is confirmed by the affixed
IPPC logo.
or
– Carton in accordance with European Packaging Directive 94/62EC; recyclability is confirmed
by the affixed RESY symbol.
• Seaworthy packaging (optional): Wood crate, treated in accordance with ISPM 15 standard, which
is confirmed by the affixed IPPC logo.
• Carrying and mounting hardware:
– Disposable plastic pallet
– Plastic straps
– Plastic adhesive strips
• Dunnage: Paper cushion

Proline Promass E 200 HART Mounting
Endress+Hauser 17
6 Mounting
6.1 Mounting requirements
No special measures such as supports are necessary. External forces are absorbed by the construction
of the device.
6.1.1 Mounting position
Mounting location
A0015595
To prevent measuring errors arising from accumulation of gas bubbles in the measuring tube, avoid
the following mounting locations in the pipe:
• Highest point of a pipeline.
• Directly upstream of a free pipe outlet in a down pipe.
Installation in down pipes
Notwithstanding the above, the following installation proposal permits installation in an open down
pipe. Pipe restrictions or the use of an orifice plate with a smaller cross-section than the nominal
diameter prevent the sensor running empty while measurement is in progress.

Mounting Proline Promass E 200 HART
18 Endress+Hauser
1
2
3
4
5
A0015596
å 4 Installation in a down pipe (e.g. for batching applications)
1 Supply tank
2 Sensor
3 Orifice plate, pipe restriction
4 Valve
5 Batching tank
DN Æ Orifice plate, pipe restriction
[mm] [in] [mm] [in]
8 3/8 6 0.24
15 ½ 10 0.40
25 1 14 0.55
40 1½ 22 0.87
50 2 28 1.10
Orientation
The direction of the arrow on the sensor nameplate helps you to install the sensor according to the
flow direction (direction of fluid flow through the piping).
Orientation Compact version
AVertical orientation
A0015591
BHorizontal orientation, transmitter head
up
A0015589
Exception:
CHorizontal orientation, transmitter head
down
A0015590
1)
Exception:
DHorizontal orientation, transmitter head
at side
A0015592
1) Applications with high process temperatures can increase the ambient temperature. This orientation is recommended
to observe the maximum ambient temperature for the transmitter.

Proline Promass E 200 HART Mounting
Endress+Hauser 19
If a sensor is installed horizontally with a curved measuring tube, match the position of the sensor
to the fluid properties.
1 2
A0014057
å 5 Orientation of sensor with curved measuring tube
1 Avoid this orientation for fluids with entrained solids: Risk of solids accumulating.
2 Avoid this orientation for outgassing fluids: Risk of gas accumulating.
Inlet and outlet runs
No special precautions need to be taken for fittings which create turbulence, such as valves, elbows
or T-pieces, as long as no cavitation occurs (® ä 19).
A0015597 A0015598
Installation dimensions
For the dimensions and installation lengths of the device, see the "Technical Information"
document, "Mechanical construction" section
6.1.2 Requirements from environment and process
Ambient temperature range
Measuring device –40 to +60 °C (–40 to +140 °F)
Local display –20 to +60 °C (–4 to +140 °F), the readability of the display may be impaired at
temperatures outside the temperature range.
►If operating outdoors:
Avoid direct sunlight, particularly in warm climatic regions.
System pressure
It is important that cavitation does not occur, or that gases entrained in the liquids do not outgas.
Cavitation is caused if the pressure drops below the vapor pressure:
• In liquids that have a low boiling point (e.g. hydrocarbons, solvents, liquefied gases)
• In suction lines
►Ensure the system pressure is sufficiently high to prevent cavitation and outgassing.

Mounting Proline Promass E 200 HART
20 Endress+Hauser
For this reason, the following mounting locations are recommended:
• At the lowest point in a vertical pipe
• Downstream from pumps (no danger of vacuum)
A0015594
Thermal insulation
For some fluids, it is important to keep the radiated heat from the sensor to the transmitter to a
minimum. A wide range of materials can be used to provide the required thermal insulation.
NOTICE
Electronics overheating on account of thermal insulation!
►Observe maximum permitted insulation height of the transmitter neck so that the transmitter
head is completely free.
mm (in)
£20 (0.79)
A0013937
Heating
NOTICE
Electronics can overheat due to elevated ambient temperature!
►Observe maximum permitted ambient temperature for the transmitter (® ä 19).
►Depending on the fluid temperature, take the device orientation requirements into account
(® ä 18).
Heating options
If a fluid requires that no heat loss should occur at the sensor, users can avail of the following heating
options:
• Electrical heating, e.g. with electric band heaters
• Via pipes carrying hot water or steam
• Via heating jackets
Using an electrical trace heating system
If heating is regulated via phase angle control or pulse packages, magnetic fields can affect the
measured values (= for values that are greater than the values approved by the EN standard (sine
30 A/m)).
For this reason, the sensor must be magnetically shielded: the housing can be shielded with tin plates
or electric sheets without a privileged direction (e.g. V330-35A).
The sheet must have the following properties:
•Relative magnetic permeability mr ³ 300
•Plate thickness d ³ 0.35 mm (d ³ )0.014 in