Endress+Hauser Proline t-mass 65 PROFIBUS DP User manual

BA114D/06/en/02.06
71021610
Valid as of version
V 3.02.XX (Device software)
Description of Device Functions
Proline t-mass 65
PROFIBUS DP
Thermal Mass Flow Measuring System
8

Device Functions Proline t-mass 65 PROFIBUS DP
2Endress+Hauser

Device Functions Proline t-mass 65 PROFIBUS DP Table of contents
Endress+Hauser 3
Table of contents
1 Function matrix Proline t-mass 65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 The function matrix: layout and use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Graphical illustration of the function matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2GroupMEASURINGVALUES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Group SYSTEM UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Group QUICK SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Quick Setup “Commissioning” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Quick Setup “Communication” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3 Data back-up with “T-DAT SAVE/LOAD” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Group OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Group USER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7 Group TOTALIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8 Group COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
9 Group PROCESS PARAMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10 Group GAS MIXTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11 Group SYSTEM PARAMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
12 Group SENSOR DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
13 Group SUPERVISION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
14 Group SIMULATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
15 Group SENSOR VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
16 Group AMPLIFIER VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
17 Factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
17.1 SI units (not for USA and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
17.2 US units (only for USA and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Index of key words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Table of contents Device Functions Proline t-mass 65 PROFIBUS DP
4Endress+Hauser

Device Functions Proline t-mass 65 PROFIBUS DP 1 Function matrix Proline t-mass 65
Endress+Hauser 5
1 Function matrix Proline t-mass 65
1.1 The function matrix: layout and use
The function matrix is a two-level construct: the groups form one level, functions the other.
The groups are the highest-level grouping of the control options for the flowmeter.
Each group comprises a number of functions.
You select a group in order to access the individual functions for controlling or parameterizing the
flowmeter.
You will find an overview of the groups in the table of contents on Page 3 and in the graphical
representation of the function matrix on Page 6.
You will also find an overview of the functions on Page 6, complete with the page references of the
detailed function descriptions.
The descriptions of the individual functions start on Page 7.
Example of how to parameterize a function (in this case changing the language for
the user interface):
➀Entry into the function matrix (F-key).
➁Select the OPERATION group.
➂Select the LANGUAGE function, change the setting from ENGLISH to DEUTSCH
with OS and save F(all texts displayed on the user interface appear in German).
➃Exit the function matrix (ESC > 3 seconds).
A0001142
>3s
-+E
Esc
E
E
E
E
E E E E E
–
+
+
Esc
–
+
Esc
–
+
Esc
–
E
m
n
o
p

1 Function matrix Proline t-mass 65 Device Functions Proline t-mass 65 PROFIBUS DP
6Endress+Hauser
1.2 Graphical illustration of the function matrix
BLOCK SELECTION
(p. 24)
GAS TYPE 5
(p. 31)
TEST DISPLAY
(p. 19)
CYCL. CALC. TOT.
(p. 22)
CHECK CONFIG.
(p. 24)
REFERENCE DENSITY
(p. 28)
% FRACTION 4
(p. 31)
SAVE CHANGES
(p. 33)
BACKLIGHT
(p. 19)
MODE TOTALIZER
(p. 22)
DEVICE ID
(p. 24)
REFERENCE PRESSURE
(P. 28)
GAS TYPE 4
(p. 31)
CHECK VALUES
(p. 33)
CONTRAST LCD
(p. 19)
PRESET TOTALIZER
(p. 21)
ACTUAL BAUD RATE
(p. 24)
REFERENCE
TEMPERATURE (p. 28)
% FRACTION 3
(p. 31)
% FRACTION 8
(p. 32)
FLOW CONDITIONER
(p. 36)
UNIT LENGTH
(p. 9)
DISPLAY DAMPING
(p. 19)
SET TOTALIZER
(p. 21)
PROFILE VERSION
(p. 24)
AO - PRESSURE VALUE
(p. 25)
PROCESS PRESSURE
(p. 27)
GAS TYPE 3
(p. 31)
GAS TYPE 8
(p. 32)
ZERO POINT
(p. 36)
HOURS SINCE RESET
(p. 37)
PRE-AMPLIFIER HARD-
WARE REV. NO. (p. 39)
SOFTWARE REV. NO.
I/O MODULE (p. 40)
UNIT DENSITY
(p. 9)
ACCESS CODE
COUNTER (p. 16)
FORMAT
(p. 18)
UNIT TOTALIZER
(p. 21)
UNIT TO BUS
(p. 24)
AO - DISPLAY VALUE
(p. 25)
INSTALLATION
FACTOR (p. 27)
% FRACTION 2
(p. 30)
% FRACTION 7
(p. 32)
INTERNAL WIDTH
(p. 36)
OPERATION HOURS
(p. 37)
PRE-AMPLIFIER SOFT-
WARE REV. NO. (p. 39)
I/O MODULE TYPE
(p. 40)
UNIT TEMPERATURE
(p. 9)
STATUS ACCESS
(p. 16)
100% VALUE LINE 2
(p. 18)
CHANNEL
(p. 20)
SELECTION GSD
(p. 23)
AI3 - OUT VALUE
(p. 25)
ZERO POINT ADJUST
(p. 27)
GAS TYPE 2
(p. 30)
GAS TYPE 7
(p. 32)
INTERNAL HEIGHT
(p. 36)
SYSTEM RESET
(p. 37)
SOFTWARE REVISION
NUMBER S-DAT (p. 39)
SOFTWARE REVISION
NUMBER T-DAT (p. 40)
TEMPERATURE
(p. 7)
UNIT PRESSURE
(p. 8)
T-DAT SAVE/LOAD
(p. 10)
DEFINE PRIVATE CODE
(p. 16)
100% VALUE LINE 1
(p. 18)
OVERFLOW
(p. 20)
WRITE PROTECT
(p. 23)
AI2 - OUT VALUE
(p. 25)
OFF VALUE LOW FLOW
CUT OFF (p. 26)
% FRACTION 1
(p. 30)
% FRACTION 6
(p. 32)
INTERNAL DIAMETER
(p. 35)
ALARM DELAY
(p. 37)
VALUE SIMULATION
MEASURAND (p. 38)
TRANSDUCER SERIAL
NUMBER (p. 39)
SOFTWARE REVISION NO AMPLIFIER (p. 40)
COR. VOLUME FLOW
(p. 7)
UNIT COR. VOL. FLOW
(p. 8)
QS-COMMUNICATION
(p. 10)
ACCESS CODE
(p. 15)
ASSIGN LINE 2
(p. 17)
SUM
(p. 20)
FIELDBUS ADDRESS
(p. 23)
AI1 - OUT VALUE
(p. 25)
ON VALUE LOW FLOW
CUT OFF (p. 26)
GAS TYPE 1
(p. 30)
GAS TYPE 6
(p. 32)
FLOW DAMPING
(p. 34)
NOMINAL DIAMETER
(p. 35)
PREVIOUS SYSTEM
CONDITION (p. 37)
SIMULATION
MEASURAND (p. 38)
SERIAL NUMBER
(p. 39)
HARDWARE REVISION
NO AMPLIFIER (p. 40)
MASS FLOW
(p. 7)
UNIT MASS FLOW
(p. 8)
QS -COMMISSION
(p. 10)
LANGUAGE
(p. 15)
ASSIGN LINE 1
(p. 17)
SELECT TOTALIZER
(p. 20)
TAG NAME
(p. 23)
CHANNEL
(p. 25)
ASSIGN LOW FLOW
CUT OFF (p. 26)
NUMBER OF GAS
COMPONENTS (p. 29)
% FRACTION 5
(p. 31)
POSITIVE ZERO
RETURN (p. 34)
PIPE TYPE
(p. 35)
ACTUAL SYSTEM
CONDITION (p. 37)
SIMULATION FAILSAFE
MODE (p. 38)
SENSOR TYPE
(p. 39)
DEVICE SOFTWARE
(p. 40)
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
MEASURING VALUES
(p. 7)
SYSTEM UNITS
(p. 8)
QUICK SETUP
(p. 10)
OPERATION
(p. 15)
USER INTERFACE
(p. 17)
TOTALIZER
(p. 20)
COMMUNICATION
(p. 23)
PROCESS PARAM.
(p. 26)
GAS MIXTURE
(p. 40)
SYSTEM PARAMETER
(p. 34)
SENSOR DATA
(p. 35)
SUPERVISION
(p. 37)
SIMULAT. SYSTEM
(p. 38)
SENSOR VERSION
(p. 39)
AMPLIFIER VERSION
(p. 40)

Device Functions Proline t-mass 65 PROFIBUS DP 2 Group MEASURING VALUES
Endress+Hauser 7
2 Group MEASURING VALUES
Function description MEASURING VALUES
!Note!
The engineering unit of the measured variable shown here can be set in the SYSTEM UNITS group (→ Page 8).
MASS FLOW In this function, the currently measured mass flow appears on the display.
Display:
5-digit floating-point number, including unit
(e.g. 150.00 kg/h; 330.70 lb/h; etc.)
CORRECTED VOLUME FLOW In this function, the currently measured corrected volume flow appears on the
display. The calculated corrected volume flow is derived from the measured mass
flow and the reference density of the gas (at reference temperature and pressure).
User Interface:
5-digit floating-point number, including unit
(e.g. 104.97 Nm3/h; 110.73 Sm3/h; etc.)
TEMPERATURE In this function, the currently measured gas ambient temperature appears on the
display.
Display:
5-digit floating-point number, including unit and sign
(e.g. –23.4 °C; 160.0 °F; 295.4 K; etc.)

3 Group SYSTEM UNITS Device Functions Proline t-mass 65 PROFIBUS DP
8Endress+Hauser
3 Group SYSTEM UNITS
Function description SYSTEM UNITS
You can select the unit for the measured variable in this function group.
!Note!
The factory settings of the system units described here apply to the local display and can differ from the units that are
used to transfer the measured variables to the automation system. The UNIT TO BUS function (→ Page 24), however,
allows you to set these units to the currently selected units of the local display.
UNIT MASS FLOW Use this function to select the unit for displaying the mass flow (mass/time).
The unit you select here is also valid for the low flow cut off.
!Note!
The following units of time can be selected:
s = second, m = minute, h = hour, d = day
Options:
Metric:
gram →g/time unit
kilogram →kg/time unit
Metric ton →t/time unit
US:
ounce →oz/time unit
pound →lb/time unit
ton →ton/time unit
Factory setting:
kg/h or US lb/h (country dependent, → Page 41 ff.)
UNIT CORRECTED VOLUME
FLOW
Use this function to select the unit for displaying the corrected volume flow
(corrected volume/time).
The unit you select here is also valid for the low flow cut off.
!Note!
The following units of time can be selected:
s = second, m = minute, h = hour, d = day
Options:
Metric:
Normal liter →Nl/time unit
Normal cubic meter →Nm3/time unit
US:
Standard cubic meter →Sm3/time unit
Standard cubic foot →Scf/time unit
Factory setting:
Nm3/h or Sm3/h (country dependent, → Page 41 ff.)
UNIT PRESSURE Use this function to select the unit for pressure.
The unit you select here is also valid for:
• PROCESS PRESSURE →Page 27
• REFERENCE PRESSURE →Page 28
Options:
bar a (bar absolute)
psi a (pounds per square inch absolute)
kPa a (kilopascal absolute)
Factory setting:
bar a or psi a (country dependent, → Page 41 ff.)

Device Functions Proline t-mass 65 PROFIBUS DP 3 Group SYSTEM UNITS
Endress+Hauser 9
UNIT TEMPERATURE Use this function to select the unit for displaying the temperature.
Options:
°C (Celsius)
K (Kelvin)
°F (Fahrenheit)
°R (Rankine)
Factory setting:
°C or °F (country dependent, → Page 41 ff.)
UNIT DENSITY Use this function to select the unit for displaying the calculated gas process density.
The unit you select here is also valid for the reference density
(see function REFERENCE DENSITY →Page 28)
Options:
Metric:
gram →g/cm3; g/cc
kilogram →kg/dm3; kg/l; kg/m3
US:
pound →lb/ft3
Factory setting:
kg/m3or lb/ft3(country dependent, → Page 41 ff.)
UNIT LENGTH Use this function to select the unit of length for the pipe internal diameter or
rectangular duct internal dimensions (see group SENSOR DATA →Page 35).
Options:
MILLIMETER
INCH
Factory setting:
MILLIMETER or INCH (country dependent, → Page 41 ff.)
Function description SYSTEM UNITS

4 Group QUICK SETUP Device Functions Proline t-mass 65 PROFIBUS DP
10 Endress+Hauser
4 Group QUICK SETUP
Function description QUICK SETUP
QUICK SETUP COMMISSION Use this function to start the setup menu for commissioning.
Options:
NO
YES
Factory setting:
NO
!Note!
You will find a flowchart of the Quick Setup Commissioning menu on Page 11.
For more information on Setup menus, please refer to the Proline t-mass 65
Operating Instruction BA113D/06/en/… .
QUICK SETUP
COMMUNICATION
Use this function to start the setup menu for the settings of the PROFIBUS DP
communication parameters.
Options:
NO
YES
Factory setting:
NO
!Note!
You will find a flowchart of the Quick Setup Cummunication menu on Page 14.
For more information on Setup menus, please refer to the Proline t-mass 65
Operating Instruction BA113D/06/en/… .
T-DAT
SAVE/LOAD
Use this function to save the parameter settings / configuration of the transmitter
in a transmitter DAT (HistoROM/T-DAT), or to load the parameter settings from
the HistoROM/T-DAT into the EEPROM (manual safety function).
Application examples:
• After commissioning, the current measuring point parameters can be
saved to the HistoROM/T-DAT as a backup.
• If the transmitter is replaced for some reason, the data from the
HistoROM/T-DAT can be loaded into the new transmitter (EEPROM).
Options:
CANCEL
SAVE (from EEPROM to HistoROM/T-DAT)
LOAD (from HistoROM/T-DAT into EEPROM)
Factory setting:
CANCEL
!Note!
• If the target device has an older software version, the message
#042 “TRANSM. SW-DAT” is displayed during start-up. Then only the
SAVE option is available.
•LOAD
This option is only possible if the target device has the same software version as,
or a more recent software version than, the source device.
•SAVE
This option is always available.