Energizer EN150 User manual

Owner's Guide
Printed in China
Toll Free 1-866-295-6775
WARNING:
This unit employs components that tend to produce arcs or sparks. To
prevent fire or explosion, do not install in compartments containing
batteries or flammable materials - SHOCK HAZARD. DO NOT OPEN.
CAUTION:
OUTPUT NON-SINUSOIDAL REFER TO MANUAL - Provided with integral
protection against overloads. To prevent fire, do not cover or obstruct
ventilation openings. Do not mount in zero clearance compartment.
Overheating may result.
EN150
Conforms to / Conforme à UL std. 458,
CSA std. C22.2 No. 107.1

2 Important Safety Information
Cautions identify conditions or practices that may
damage the unit or other equipment.
1 Introduction
Misusing or incorrectly connecting the
EN150
may damage the equipment or create hazardous
conditions for users. Read the following safety
instructions and pay special attention to all Caution
and Warning statements in the guide.
Warnings identify conditions that may result in
Connected to the 12-volt outlet in your vehicle, the
EN150
efficiently
and reliably
powers
a
wide
variety
of loads through both the AC outlet and USB port.
Read this guide before connecting or using the
EN150
and save
it for future reference
.
W
req
e
u
h
ir
o
e
p
a
e
n
y
y
o
a
u
s
e
si
nj
st
o
a
y
nc
u
e
s
,
in
p
g
le
yo
ase
ur
co
EN150
ntact o
a
u
n
r
d
h
i
e
f
y
lp
o
d
u
esk:
www.energizerpower.com or toll free: 1.866.295.6775
1
WARNING
Keep children away from the
EN150. The
i
powe
nvert
r
e
a
r
s
g
a
en
n
e
o
r
rma
ates
l
t
h
h
ousehol
e same
d
po
wal
ten
l
t
outlet.
ially lethal AC
Thank you for purchasing the
Energizer® EN150

2
the AC outlet. Ensure that your do not
contact the prongs of an AC plug when the plug is
partially inside the inverter.
Warnings and Cautions
The
EN150
housing
may become
uncomfortably
warm, reaching 60 °C (140 °F) under extended high
power operation. During operation, keep it away
from materials that may be affected by high
temperatures.
Do not use the
EN150
in
the
presence
of
flammable fumes or gases, such as in the bilge of a
gasoline powered boat, ornear propane tanks. Do
not use the
EN150
in
an enclosure area
containing
automotive-type,lead-acid batteries. These batteries,
unlike sealed batteries, vent explosive hydrogen gas,
which can be ignited by sparks from electrical
connections.
WARNING: Shock hazard
Use caution when inserting an AC plug into the
three-prong AC outlet. The prongs of an AC plug
can become bent from misuse. If an AC plug is
improperly inserted into the AC outlet, a bent prong
can slip outside the inverter and become a shock
hazard.
Grip the inverter carefully when inserting or
removing an AC plug. Keep your
clear of

3
CAUTION: Risk of Fire.
Do not replace any vehicle fuse with a rating higher
than recommended by the Vehicle Manufacturer.
Ensure that the electrical system in your vehicle
can supply this product without causing the vehicle
fusing to open. Information on the vehicle fuse
rating is typically found in the vehicle operator’s manual.
If a vehicle fuse opens repeatedly, do not keep on
replacing it. The cause of the overload must be found.
On no account should fuses be patched up with
tin foil or wire as this may cause serious damage
elsewhere in the electrical circuit or

4
CAUTION: Output non-sinusoidal
Some chargers for small nickel-cadmium batteries
can be damaged if connected to the
EN150.
Do not use the inverter with the following
appliances:
• Small battery-operated appliances like
rechargeable flashlights, some rechargeable
shavers, and night lights that are plugged
directly into an AC receptacle to recharge.
• Battery chargers used in hand power tools.
These chargers display a warning label stating
that dangerous voltages are present at the
charger battery terminals.
CAUTION
Do not connect live AC power to the
EN150
AC outlets. This will damage the inverter,
and the damage is not covered by warranty.
Do not connect any AC load that has its neutral
conductor connected to ground to the
EN150

5
Additional Safety Guidelines
•Do not insert foreign objects in the
EN150out lets orothe rope nings.
•Never connect the inverter to power utility AC
distribution wiring.
•Do not use the EN150in te mperatu res
over 40 °C (100 °F).
•Do not expose the EN150to wate r,rain,
snow, or spray.
Failure to follow these safety guidelines may cause
personal injury and/or damage to the EN150
It may also void your product warranty.
3 Safety Features
•Overload protection with automatic shutdown
•Low battery voltage shutdown
•High-input voltage protection with automatic
shutdown
•Overheat protection with automatic shutdown
•Output short circuit protection.

6
LED Light
indicator
AC Outlet
Ventilation opening
4 Inverter Features
EN150
USB QC3.0
5V/3A,9V/3A,12V/2.5A

7
5 Using the Inverter
Through its AC outlet, the
EN
150
is capable
of powering most 120V AC products that use
150W
or
less.
The
EN 150 cup inverter
can also power
or charge most consumer electronics that have USB
power ports.
The
EN 150
AC
output
waveform,
called
“modified sine wave” is designed to function
similarly to the sine wave shape of utility power.
Most devices are not affected by a "modified sine
wave," you may need to consult with the manufacture
of the device you wish to run prior to connection
with inverter.

8
1. Plug a DC cable into the DC cable port on the
EN150 and connect to a 12V cigarette lighter
receptacle.
2. Plug the device you want to operate into the
EN150
3. When the inverter is not in use, unplug it from the
12V outlet to prevent slight discharge of the
battery.

9
6 Inverter Operation
1.
When properly connected to a 12V outlet,
the
light will glow BLUE, indicating the inverter is
ready.
2. Plug the product(s) you want to operate into the
AC outlet or USB port and switch them on (if
necessary).
Operating Guidelines
• As the battery is used, its voltage begins to fall.
When the EN150
senses that the
voltage
at its DC input has dropped to 10.5V, the inverter
automatically shuts down and the light glows RED,
indicating a fault. This prevents the battery from
being damaged. Turn off any devices that the
EN150
is
powering.

10
Important:
Vehicle batteries are designed to provide brief
periods of very high current needed for engine starting. They
are not intended for constant deep discharge.Regularly
operating the EN1
50 from a vehicle battery until low-voltage
shutdown occurs will shorten the life of the battery.
•If an AC product rated higher than 150W
is plugged into the EN150,the inverter will
shut down. The LED light will alternate from
BLUE to REDcontinuously.
•If the EN150 exceeds a safeoperating
temperature, due to insufficient ventilation or a
high-temperature environment, it automatically
shuts down. The RED FAULT light comes on.
•Should a defective battery charging system cause
the battery voltage to rise to dangerously high
levels, the EN150 automaticall yshuts
down. The RED FAULT light comes on.

11
• In the event of an overload, low battery voltage or
overheating, the EN150 automatically
shuts down.
Battery Operating Time
Operating time will vary depending on the charge
level of the battery, its capacity and the power level
drawn by the particular AC load, USB load, or
combination of both. Witha typical vehicle battery
and a 80W load, an operating time of 4 to 5 hours or
more can be expected.
CAUTION
protection against over-vo
Although the EN150
incorporates
ltage, it may still be
damaged if the input voltage exceeds 16 V.
W
str
h
o
e
ng
n u
ly
si
reco
ng a
m
ve
me
hic
n
l
de
e ba
d t
tt
o
e
star
ry a
t
s
th
a
e
po
veh
we
i
r
cl
sour
e ever
ce,
y
it
h
i
o
s
ur
or two to recharge the battery before its capacity drops
too
engine
low.
is
The
running,
EN150
but
can
the
ope
norma
rate
wh
l
voltage
ile
the
drop that
occurs during starting of the engine may trigger the
inverter’s low voltage shutdown feature.

12
Interference with Electronic Equipment
Generally, most ACproducts operate with EN150
just as they would with household ACpower.
Below is information concerning two possible
exceptions.
Buzzing sound in audio systems and radios
Some inexpensive stereo systems and AM-FM radios
have inadequate internal power supply filtering and
will “buzz” slightly when powered by the EN150.
Generally theo ,nlysolution is anaudio product
with a higher quality filter.
Television interference
The EN150 is shielded to minimizeitsinterference
with TVsignals. However, with weak TVsignals
interference may be visible in the form of lines
scrolling across the screen. The following should
minimize or eliminate the problem:
•Increase the distance between the EN150
and the TV, antenn a and cab les.
•Adjust th e orien tation of th e EN150
tele vision, an tenn a an d cables.
•Maximize TVsigna l streng th b y usin g a be tter
antenna and use shielded antenna cab le where
possible.

13
7 Troubleshooting
PROBLEM: AC product will not operate, no inverter
lights are ON.
PROBLEM: Measured inverter output is to o low.
Possible cause Solution
Battery is defective. Check battery and replace if
required.
Loose connections. Check connections.
Possible cause Solution
Standard “average-
reading” AC voltmeter
used to measure output
voltage, resulting in an
apparent reading 5 to 15 V
too low.
Inverter’s “modied sine
wave” output requires “true
RMS” voltmeter for accurate
measurements.

14
PROBLEM: AC product will not operate,RED FAULT
light ON.
Battery voltage is too low. Recharge battery.
Possible cause Solution
AC product(s) connected
are rated at more than the
inverter’s continuous
power rating; overload
shutdown has occurred.
Use a product withapower
rating less than the inverter’s
continuous power rating.
AC product is rated less
than the inverter’s
continuous power rating;
high starting surge has
caused overload
shutdown.
Product exceeds inverter’s
surge capability. Useaproduct
with starting surge power
within the inverter’s capability.
Battery is discharged. Recharge battery.
Possible cause Solution
Unplug inverter from DC socket
and allow to cool for 15 minutes.
Remove objects covering unit.
Move the inverter to a cooler
place. Reduce load if continuous
operation is required. Restart.
The inverter has over
heated due to poor
ventilation and has shut
down.

15
Specifications are subject to change without notice.
AC Power Outpu t
AC output voltage (nominal)
Continuous AC output power
AC output waveform
Maximum AC output surge power
AC output frequency
USB DC output voltage
2X USB DC output current (max.)
EN150
115VAC/60Hz 150W
150W
Modified sine wave
300W
60 ±3Hz
5V DC
QC3.0：5V/3A,9V/3A,12V/2.5A
USB 30W max

16
0.7 lbs
thgieW
EN150
13.8V DC, 15A Max
0.4A
85%
10.5V+ 0.5V
15.5V+ 0.3V
(L)5.5 in
(W)2.4 in
(H)2.6 in
DC Power
DC input voltage range (VDC)
Battery drain with no AC load
(at 12 V input)
Efficiency (maximum)
Low voltage shutdown point (nominal)
High voltage shutdown point
(nominal)
Physical
Dimensions (milimetres )
(Length × Width × Height)

17
9 Warranty and Return
Warranty by PowerBright
What does this warranty cover?
This Limited Warranty
is provided by PowerBright and
covers defects in workmanship and materials in your
EN150.
This warranty
period
lasts for 24 months
from the date of purchase at the point of sale to you, the
original end user customer. You require proof of purchase to
make warranty claims.
What will PowerBright do? PowerBright will, at its option,
repair or replace the defective product free of charge,
provided that you notify PowerBright of the product defect
within the Warranty Period, and provided that PowerBright
through inspection establishes the existence of such a defect
and that it is covered by this Limited Warranty.
PowerBright will, at its option, use new and/or reconditioned
parts in performing warranty repair and building
replacement products. PowerBright reserves the right to
use parts or products of original or improved design in the repair or
replacement. If PowerBright repairs or replaces a product, its
warranty continues for the remaining portion of the original
Warranty Period or 90 days from the date of the return

18
shipment to the customer, whichever is greater. All replaced
products and all parts removed from repaired products
become the property of PowerBright.
PowerBright covers both parts and labor necessary to repair the
product, and return shipment to the customer via a PowerBright
selected non-expedited surface freight within the contiguous
United States and Canada. Alaska and Hawaii are excluded.
Contact PowerBright Customer Service for details on freight
policy for return shipments outside of the contiguous United
States and Canada.
How do you get service?
If your product requires troubleshooting or warranty
service, contact your dealer.
If you are unable to contact your dealer, or the dealer is
unable to provide service, contact PowerBright directly at:
Direct returns may be performed according to the PowerBright
Return Material Authorization Policy described in your
product manual. For some products, PowerBright maintains a
network of regional Authorized Service Centers. Call
PowerBright or check our website to see if your product
can be repaired at one of these facilities.
Toll Free: 1 866 295 6775
Website: www.PowerBright.com

19
What does this warranty not cover? This Limited
Warranty does not cover normal wear and tear of the product
or costs related to the removal, installation, or
troubleshooting of the customer's electrical systems. This
warranty does not apply to,and PowerBright will not be
responsible for,any defect in or damage to:
a) the product if it has been misused, neglected, improp-
erly installed, physically damaged or altered, either
internally or externally, or damaged from improper use
or use in an unsuitable environment;
b) the product if it has been subjected to fire, water,
generalized corrosion, biological infestations, or input
voltage that creates operating conditions beyond the
maximum or minimum limits listed in the PowerBright
product specifications including high input voltage
from generators and lightning strikes;
c) the product if repairs have been done to it other than by
PowerBright or its authorized service centers
(hereafter "ASCs");
d) the product if it is used as a component part of a prod-
uct expressly warranted by another manufacturer;
e) the product if its original identification (trade-mark,
serial number) markings have been defaced, altered, or
removed.