Enfora GSM1308 User manual

Unitronics
1
The GSM-41J Modem Kit: Enfora GSM1308/1318
This kit enables your SMS-enabled OPLC to communicate via cellular networks.
The kit contains an Enfora GSM1308/1318 modem and related hardware.
The modem can communicate via GSM, GPRS + TCP/IP at 850/900/1800/1900 MHz.
Note:
Standard Vision controllers only: V120, V230, V260, V280, V530, V290 (V290-19-B20B only)
VisiLogic programs including the GPRS Function Block must use FB V5.04 and later. To learn how to
update FBs, refer to the VisiLogic Help topic FBs Library.
Connection
The figure below shows you how to assemble the different elements of the Enfora GSM1308/1318
modem, and how to connect the modem to an OPLC.
Component Identification
#
Description
Notes
1 Communication cable,
controller to modem
Vision Series / M90/91 Series:
To connect the modem to the PLC, use the standard programming
cable that is supplied with your controller, or with your controller's
programming kit.
Jazz Series:
Jazz does not comprise an embedded communication port
Add-on ports are available by separate order
Use the communication cable supplied with the Add-on port
2
GSM antenna connector
Located on modem
3 GSM antenna
4
SIM card slot
Located on modem. See page 2
5
LED
Located on modem. See page 2
6 9-pin RS232 port Located on modem
7
9 pin male adapter
p/n MJ10-22-CS72
8
Power supply socket
Located on modem
9
Power supply cable
Cable p/n 211300508

Enfora GSM1308/1318 modem
Modem kit
2
Unitronics
SIM Card
To insert the SIM card, slide it into the slot until
it clicks into place, and then slide the lock to
the left.
To remove the card, slide the lock to the right
and then press the card; a spring releases and
partially ejects the card.
Modem RS232 port pin-out
D-type 9 pin female connector:
Pin
Description
Direction
1 DCD (Data Carrier Detect) O
2
RxD (Receive Data)
O
3
TxD (Transmit Data)
I
4 DTR (Data Terminal Ready) I
5
GND (Signal Ground)
-
6
DSR (Data Set Ready)
O
7
RTS ( Request to Send)
I
8
CTS (Clear To Send)
O
9
RING (Ring Indicator)
O
LED: Status Indication
The modem has one green LED on the panel labeled REG (shown above).
REG indicates GSM network registration status.
Flashing, when attempting to register on a GSM network.
Continually lit, when the modem is registered with a GSM network.

Modem kit
Enfora GSM1308/1318 modem
Unitronics
3
Mounting
Use the screw brackets shown in the following figure to mount the device.

Enfora GSM1308/1318 modem
Modem kit
4
Unitronics
Technical Specifications
Modem
Power voltage range
6 - 40VDC
Status indication
LED - see page 2
SIM card
3V (with locking mechanism)
GSM frequency 850/900/1800/1900 MHz
Weight
147g (5.19oz)
Dimensions 63.5x63.5x23.9mm (2.5”x2.5”x0.94”)
Operational temperature
-30 to 70°C (-22 to 158°F)
Storage temperature
-40 to 85°C (-40 to 185°F)
Antenna connector type
SMA female
Antenna
Antenna frequency
Quad band GSM:850/900/1800/1900 MHz
Unitronics product sold hereunder can be used with certain products of other manufacturers at the
user’s sole responsibility.
The information provided is subject to change without notice.
The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole
discretion, and without notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or
temporarily withdraw any of the forgoing from the market.
All information in this document is provided "as is" without warranty of any kind, either expressed or implied, including but not limited to any implied warranties of
merchantability, fitness for a particular purpose, or non-infringement. Unitronics assumes no responsibility for errors or omissions in the information presented in
this document. In no event shall Unitronics be liable for any special, incidental, indirect or consequential damages of any kind, or any damages whatsoever arising
out of or in connection with the use or performance of this information.
The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other
third parties and you are not permitted to use them without the prior written consent of Unitronics or such third party as may own them.
DOC01001-B0 01/14