ENFORCER SL-3301-BAQ User manual

SL-3301-BAQ
Multi-Color LED Strobe Light
Manual
•
Utilizes high-intensity LEDs
•5 Vertical LED strips (25 LEDs total)
increase isibility from arious directions
•Adjustable strobe speed, 60~260 times/min
•High-impact resistant case
•High-impact and heat-resistant lens
•Re erse polarity protection
•Weather resistant – IP66
Features
:
•7 Colors possible – Red, green, blue,
cyan, magenta, yellow, and white
•Operating life of o er 50,000 hours
(o er 5.7 years)
•Simple 2- to 5-wire installation
•Set color ia DIP switches, or trigger
colors with an external de ice ia 3
trigger input wires

ENFORCER Multi-Color LED Strobe Light
2SECO-LARM U.S.A., Inc.
The
ENFORCER
Multi
-
Color
LED Strobe Light
pro ide
s
all the functions of a re
gular strobe light, but with
more ersatility. The Multi-Color LED Strobe Light can change between se en different colors which can be
set manually ia DIP switches, or triggered by an external de ice ia 3 trigger input wires. There are 5 ertical
LED strips, making the light more isible from arious directions, and a ariable resistor to adjust flashing
speed. The Multi-Color LED Strobe Light has an operating life of 50,000 hours — o er 160 times that of a
regular strobe light. No more bulbs to replace!
Overview:
Parts List:
1x
LED Strobe Light
1x
Manual
2x
Mounting Screw
with “O” ring
Specifications
:
Vertical LED strips
5
Total number of LEDs
25
Possible colors
Red, green, blue, cyan, magenta,
yellow, white
Operating oltage
9~
24
VAC/VDC
Current draw @12VDC (max.)
Strobe
3
50mA
Steady ON
3
50mA
Adjustable strobe speed
Maximum setting
26
0
times/min
Minimum setting
6
0 times/min
Operating life
O er 50,000 hours (o er 5.7 years)
Operating
temperature
-
4°~144
° F
(
-
20°~65
° C)
Electrical protection
Re erse polarity protected
IP rating
IP66
Base
High
-
impact
resistant
black ABS
Lens
High
-
impact
heat
-
resistant acrylic
Dimensions
3
15
/
16
"
x3
1
/
8
"
(100x79
mm)
Circuit board
Rubber “O” ring
Power wire (brown)
Ground wire
(black)
DIP Switches
(for Power ON mode)
Circuit board
LEDs
LED
Strobe or
steady ON jumper
(default, strobe)
Remo e thinned
-
out slot for
surface wiring
Circuit board screw
Trigger wires
Vertical LED strips
SECO-LARM
®
SL
-
3301
-
BAQ
Strobe
Steady ON
+
+
-
170–226
B1
B2
G1
G2
R1
R2
Blue
Green
Red
Mounting screw with
rubber “O” ring
Green trigger wire
Red trigger wire
Blue trigger wire
Strobe speed control
Strobe Steady ON
Intro uction
:

ENFORCER Multi-Color LED Strobe Light
SECO-LARM U.S.A., Inc. 3
Configuring
LED Color an Strobe
:
1.
Decide where the LED strobe light is to be mounted.
Use a pencil to mark the location of the two mounting
screws.
2. Drill a hole through the wall or surface where the LED
strobe light is to be mounted. Run the ground (black)
and power (brown) wires through the wall.
NOTE: For surface wiring applications, remo e the
thinned-out slot with a pair of pliers.
3. Connect the wires to their respecti e locations on an
alarm control panel or other security panel.
4.
Remo e the lens and mount the LED strobe light to
the surface using the two included mounting screws
with rubber “O” rings. If screws are fastene too
tightly, the “O” rings will be amage .
5. Select the color and strobe setting using the DIP
Switches (see chart below for details) and adjust
the speed using the strobe speed control
(clockwise
to increase, counterclockwise to decrease).
6. Replace lens. If lens is fastene too tightly, the
“O” ring will be amage .
Installation
:
IMPORTANT: Disconnect power before adjusting DIP switches.
B1
B2
G
1
G2
R
1
R2
Trigger Mo e
•
Before starting, please read this manual carefully and keep it for future reference.
•Be sure to use the LED strobe light within the gi en electrical limits.
Power ON Mo e
1.
Decide where the LED strobe light is to be mounted.
Use a pencil to mark the location of the two mounting
screws.
2. Drill a hole through the wall or surface where the LED
strobe light is to be mounted. Run the ground (black)
and trigger (blue, green, red) wires through the wall.
NOTE: For surface wiring applications, remo e the
thinned-out slot with a pair of pliers.
3. Connect the wires to their respecti e locations on an
alarm control panel, other security panel, or trigger
de ice according to the color desired (see chart below).
4.
Remo e the lens and mount the LED strobe light to
the surface using the two included mounting screws
with rubber “O” rings. If screws are fastene too
tightly, the “O” rings will be amage .
5. Set the LEDs to "strobe" or "steady ON" ia the
jumper, and adjust the strobe speed using the
strobe speed control (clockwise to increase,
counterclockwise to decrease).
6. Replace lens. If lens is fastene too tightly, the
“O” ring will be amage .
Default DIP Switch Setting: Red strobe
Color Strobe Setting
LED
Jumper
DIP Switch
Configuration
Trigger Wire
Connections
Red LEDs strobe continuously
Strobe R2 ON only (default) Connect red wire to GND
LEDs are steady ON Steady ON R1 ON only
Green LEDs strobe continuously
Strobe G2 ON only Connect green wire to GND
LEDs are steady ON Steady ON G1 ON only
Blue LEDs strobe continuously
Strobe B2 ON only Connect blue wire to GND
LEDs are steady ON Steady ON B1 ON only
Cyan LEDs strobe continuously
Strobe G2 and B2 ON Connect green and blue
wires to GND
LEDs are steady ON Steady ON G2 and B2 ON
Magenta
LEDs strobe continuously Strobe R2 and B2 ON Connect red and blue wires
to GND
LEDs are steady ON Steady ON R2 and B2 ON
Yellow LEDs strobe continuously
Strobe R2 and G2 ON Connect red and green
wires to GND
LEDs are steady ON Steady ON R2 and G2 ON
White LEDs strobe continuously
Strobe R2, G2, and B2 ON Connect all three trigger
wires to GND
LEDs are steady ON Steady ON All ON
NOTE:
For Trigger Mode,
LED
strobe and steady on setting is set
with jumper, see Overview (pg. 2).

ENFORCER Multi-Color LED Strobe Light
4SECO-LARM U.S.A., Inc.
Dimensions:
NOTICE
:
The SECO
-
LARM policy is one of continual de elopment and impro ement. For that reason, SECO
-
LARM
reser es the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respecti e owners. Copyright © 2019 SECO-LARM U.S.A., Inc. All
rights reser ed.
SECO
-
LARM
®
U.S.A., Inc.
16842 Millikan A enue, Ir ine, CA 92606
Website: www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
PITSW1
Order Part#: 762-514%
MI_SL-3301-BAQ_190619.docx
Replacement
White Diffuser Lens Con uit Drop Con uit Box
LED
Strobe Lights
SL
-
126
L
Q/WD
SL
-
1901
-
DAQ
SL
-
1901
-
JAQ
SL
-
1301
-
SAQ Series
Con uit Application Photos
Conduit Drop
Conduit Box
Both
Also Available from
SECO
-
LAR
M
®
:
The LED strobe light does not turn on
•
Check the LED strobe light’s power source
The LED strobe light does not flash correctly
•
Disconnect power, reconfigure LED color and strobe
settings, and reconnect power
WARRANTY:
This SECO
-
LARM product is warranted against defects in
material and workmanship while used in normal
ser ice for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defecti e part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is oid if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusi e remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no e ent shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
Troubleshooting
:
Top View
Front View
Bottom View
3
15
/
16
"
(100mm)
2
13
/
16
"
(71mm)
2
1
/
8
"
(54mm)
3
1
/
8
"
(79mm)