ENFORCER ST-BT02Q User manual

ENFORCER 12VDC Tester with Continuity
4 SECO-LARM U.S.A., Inc.
Battery load test fails
•
Charge the battery fully for best results.
•Re lace battery being tested.
Voltage dro test fails
•
Use SECO-LARM ST-HB105-TTQ Voltage Booster to increase the
amount of voltage resent.
•Reduce length of wiring.
•Decrease gauge of wire used (increase thickness of wire).
PTC fuse test fails
•
Check PTC soldering to make sure it is correctly a lied.
•Re lace PTC fuse.
Continuity test
yields
false negative
•
Change the internal battery. Be sure to store tester in Voltage Test mode.
Troubleshooting:
WARRANTY
This SECO
-
LARM roduct is warranted against defects in material and workmanshi while used in normal
service for a eriod of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the re air or re lacement of any defective art if the unit is returned, trans ortation re aid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, hysical or electrical misuse or abuse, neglect,
re air, or alteration, im ro er or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equi ment is not o erating ro erly as a result of causes other than defects in material and workmanshi . The
sole obligation of SECO-LARM, and the urchaser’s exclusive remedy, shall be limited to re lacement or re air only, at
SECO-LARM’s o tion. In no event shall SECO-LARM be liable for any s ecial, collateral, incidental, or consequential
ersonal or ro erty damages of any kind to the urchaser or anyone else.
NOTICE: The information and s ecifications rinted in this manual are current at the time of ublication. However, the
SECO-LARM olicy is one of continual develo ment and im rovement. For this reason, SECO-LARM reserves the right to
change s ecifications without notice. SECO-LARM is also not res onsible for mis rints or ty ogra hical errors.
Co yright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be re roduced or co ied, in whole
or in art, without the written ermission of SECO-LARM.
SECO
SECOSECO
SECO-
--
-LARM
LARMLARM
LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: [e-mail]
PITSW1
mi
-
ST
-
BT02Q_1003.docx
Order Part #763-168%
Test #
6
: PTC Fuse Test
(
1 V
DC
O
nly)
1. Using the alligator test leads, connect the cli s to the leads or terminals of the fuse being tested.
2. De ending on the fuse rating, use the load selection switch to select either 0.5A or 1.0A load for testing.
3. Press and hold the test button for about 3 seconds and the voltage indicator LED will turn on to
indicate the voltage out ut condition. Wait about 30 seconds for the unit to cool before erforming
further tests.
Fuse condition Test result
Normal LEDs will show voltage. If
“Test Done” LED switches
ON, end the test.
Tri ed LEDs will not switch ON if
the PTC is o en due to
overload or malfunction.
PTC Fuse Testing
EVP
-
1SD2P4UL
12VDC Power Su ly
Changing the
B
attery:
(
Use
type
3VDC CR1 0
battery
)
1. O en the to of the case by a lying ressure inward and u ward at the oint right above the
mounting hook on one side. The to cover will uncli . The PC board may come out, this is normal.
2. Use a fingernail to gently ush the gold-colored metal retaining stri on the battery holder away
from the battery. The battery will o free. Re lace only with a 3VDC CR1 0 ty e dry cell battery.
3. After re lacing the battery, sna the cover back on one side at a time. Ensure internal wires are
not inched by housing or housing guide ins and that indicator LEDs are correctly aligned.
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-com liant roducts.
Manual
ST
-
BT0
Q
12VDC
Tester
with Continuity (LED Only)
Continuity  Voltage  Polarity  Load  Voltage Dro  PTC Fuse
6-in-1 Tester
Performs the following tests:
The ENFORCER ST-BT0 Q 12VDC Tester with Continuity is a com act unit that erforms six
essential troubleshooting tests in the field including continuity testing. 4 individually lit LEDs show the
strength of the voltage resent from excellent to oor, two se arate LEDs show the rogress of the
test and one LED shows continuity during continuity testing. Illuminating igtail connector shows AC,
DC and olarity, while included alligator cli s allow it to connect easily in any situation.
Voltage
AC

ENFORCER 12VDC Tester with Continuity
2 SECO-LARM U.S.A., Inc.
IMPORTANT NOTES
:
1. NEVER CONNECT THE ST-BT0 Q TO AC POWER. DOING SO WILL VOID THE
MANUFACTURER’S WARRANTY AND MAY PERMANENTLY DAMAGE THE TESTER.
2. THE ILLUMINATING DC JACK LED WILL SHOW PURPLE TO INDICATE VAC IS PRESENT. IF
THIS OCCURS, UNPLUG THE UNIT IMMEDIATELY.
3. THE TESTER IS INTENDED FOR USE WITH 1 VDC. NEVER EXCEED 30VDC. The unit’s ower
LED will show a blue color when connected to voltages 21~30 VDC for indication ur oses only.
4. Load testing takes no longer than a few seconds. Significant heat is normal when load testing but
ressing the test button for too long will cause the unit to overheat.
5. When load testing, wait 30 seconds between tests to allow the unit to cool.
6. The unit should be stored in Voltage Test mode in order to revent draining the battery.
LED Strength Indicators:
Illuminat
ing
DC jack in ut:
Female DC jack input connects
directly to 2.1mm jacks for testing.
DO NOT CONNECT AC
POWER
Tester
Overview
:
Mounting hook
Included
lead with
alligator cli s
Load
T
est
button
Specifications
:
O erating voltage
12
VDC
Maximum load
0.5 /
1 A
(switch
selectable
)
Power
Continuity test: 3VDC CR1220 ty e battery
All other tests: Passive, no ower required
Weight
1.4 oz (40g)
Dimensions
2" X 1
3
/
4
" X 1
1
/
8
" (51 X 44 X 29 mm)
Blue: Excellent
Green: Good
Yellow: Weak
Red: Bad
Red: In ut 3~15.6VDC
Blue: In ut >21VDC
Tester Status Indicators:
Red:
Test Done
LED to indicate
c
ontinuity when
in Continuity Test mode
Load selection switch:
0.5A / 1.0A
Test
mode
switch
:
Continuity / Voltage
Test #
1
:
Continuity
Test
1.
Switch the tester to Continuity Test mode using the mode switch on the
u er side of the unit.
2. Ensure the circuit to be tested is un owered. Using the alligator test leads,
connect the unit across the test circuit. If the circuit is continuous, the red
Continuity LED will illuminate.
3. When testing long lengths of wire, it is easiest to test two wires at once.
Connect the wires together at one end, and attach one alligator test lead
to each of the other two ends. Be sure the circuit is not live while testing.
4. Always return the tester to the Voltage Test mode using the mode switch,
or the battery will drain.
Continuity Testing
SM
-
204
Magnetic
Contact
ENFORCER 12VDC Tester with Continuity
SECO-LARM U.S.A., Inc 3
Test #
4
: Load Test
(1 VDC Only)
1. Using the alligator test leads, connect each cli to the ower source being tested.
2. De ending on the a lication, use the load selection switch to select a 0.5A or 1A load for testing.
3. Press and hold the Load Test button for 6~10 seconds. The four LEDs (red, yellow, green and blue)
will show the strength of the voltage resent under the load that has been selected.
4. When the “Test Done” LED illuminates, release the Load Test button. The Load Test button should
not be held ast this time. Wait about 30 seconds for the unit to cool before erforming further tests.
Voltage, Load, and Polarity Testing
•Test battery or su ly voltage
•Test voltage under a load
•Test olarity at a glance
Polarity
Voltage
Load
Battery
Test #
5
: Voltage Drop Test
(1 VDC Only)
1. Connect the illuminating DC jack to the ower source’s DC
lug. If necessary, use alligator cli s. Note the voltage.
2. Set and a ly a load that matches the camera. Note the voltage.
3. The difference between the ower source’s voltage and the
voltage reading at the end of the cable run indicates the
voltage dro .
Note: Be sure to use DC power only.
Voltage Drop Testing
EV
-
1626
-
NKGQ
CCTV Camera
EVP
-
1SD2P4UL
DC Power Su ly
LED Color Voltage Present Power LED
Blue 11.9~15.6 VDC (±3%) OFF (no ower) : <3VDC
Green 10.8~11.9 VDC (±3%) ON Red: 3~15.6 VDC
Yellow 10.1~10.8 VDC (±3%) OFF: 15.6~21 VDC
Red 9.4~10.1 VDC (±3%) ON Blue: 21~30 VDC
Blue
Green
Yellow
Red
Test #
: Voltage Test
(DC Voltage Only)
1. Using the alligator test leads, connect each cli to the out ut wires or terminals being tested.
2. The four LEDs (red, yellow, green and blue) will dis lay the voltage resent as shown in the table
below. The ower LED will turn on for voltage from 3~15.6 VDC and 21~30 VDC.
3. The ower LED will turn red for voltage from 3~15.6 VDC and blue for voltage from 12~30 VDC.
Note: Unit is intended for use with 1 VDC. Power LED shows 4VDC for indication purposes only.
Test #
3
: Polarity Test
(1 VDC Only)
1. Connect the test leads to the wires or terminals being tested.
2. Plug the 2.1mm DC illuminating jack directly into the 2.1mm
DC jack of any 12VDC ower source.
3. The illuminating connector will show the olarity of the ower
resent. Intensity of the LED is ro ortional to the voltage.
LED Color Polarity
No color No voltage resent
Red Incorrect olarity
Blue Correct olarity
Pur le AC voltage resent
Unplug Immediately
OR