EnGenius caprive portal ready User manual

EnGenius Captive Portal “Ready”
Quick Installation Guide
Version 1.1 (for Cloud4Wi)
*** MUST READ ***
The package labelled “Captive Portal Ready” herein contains a Third-Party firmware &
management feature It has distinctly different properties, configuration and capabilities
of that the stock product mentioned in the datasheet, CD user manual and box
packaging This Quick Installation Guide supersedes any datasheet, CD user manual
and information on the box packaging to contain important instructions in setting up
your EnGenius Captive Portal Ready wireless networks Please read and follow this
guide thoroughly to have an enjoyable experience in setting up your EnGenius Captive
Portal Ready Wireless Network
Note: Guest authentication feature requires a separate paid subscription from third-
party cloud captive providers to work
Check List:
•Internet connection should be already setup & ready to use* (ADSL /Cable/Fiber modem router)
•Modem/Router must provide RJ45 port to connect with EAP300-CP or ENS202EXT-CP An Ethernet cable
is further required for the ENS202EXT-CP
•Internet Browser (Recent version of Microsoft Internet Explorer or Firefox browser)
•A pencil or pen ready to use “My Personal Notes” on the last page to assist you in remembering
any account names and passwords created
Important Notes:
•(*) The internet connection should give you the ability to ping www yahoo com (resolve DNS) and to
normally browse a web page via http and https (SSL) If in doubt, use a laptop or computer with your
existing internet connection (which you will be connecting the equipment to) and type
http://www yahoo com on your browser If there is no response, you need to resolve this with your internet
service provider before proceeding further this Quick Installation Guide

Installing the device
ST P 1
Follow the instructions on the user ID-sticker The sticker is located on the device
Go to http://controlpanel cloud4wi com and logon with your your account If you do not have an
account, kindly contact an Authorized Cloud4WI Distribution Partner
2

ST P 2
Once you have logged in, click on <+Create New> to activate the device with your account
Under the Router Menu, kindly ensure the fields are entered as follow:
Router type : nGenius
MAC address : 88:DC:96:XX:XX:XX
Note: Change XX to the similar characters as shown on your device or ID-Sticker.
Click on <Save> when completed
3

ST P 3
After the adding the device in the controlpanel cloud4wi com, connect a LAN cable from the LAN
port of your existing Internet modem router to the ethernet port of the EnGenius Captive Portal
Ready device and power up The device will perform an initial setup which the status LED will
constantly blink for 2 minutes After approximately two minutes, the product is ready This can be
verified by the 3 LEDs on the device (The WLAN LED of the ENS202EXT-CP is not in use in the
Captive Portal Mode)
For ENS202EXT-CP devices,
Note: The ENS202EXT-CP must only be powered with the supplied 24V power adapter via the PoE
(Power over Ethernet) injector
For EAP300-CP devices,
Note: The EAP300-CP supports both IEEE802 3af PoE (Power over Ethernet) or the included
power adapter You may use either one as the power source Do not use both at the same time.
In the wireless SSID scan, you can find the SSIDs by ‘My Hotspot is getting ready’ Once the initial
setup is completed, you find 3 SSIDs: MyHotspot, My Private (key is on the sticker) and Hotspot
[part of user ID]@[IP-address] This last SSID is the help SSID This is the IP-address that is
assigned on your Local Area Network The fourth SSID is the Wireless Mesh which is used to
repeat the wireless signal to another device if the other device has not Ethernet connection
4

ST P 4
Your device is now ready to use Connect to the SSID “ My Hotspot” and a simple authentication will appear
as below before internet access is allowed
Changing of Guest Access
For any changes of access such as vouchers, email, sms, social media login by guest, you can
login at http://controlpanel cloud4wi com with your account and select the desired packages
Kindly note paid subscription applies accordingly
Changing of hardware configuration
To change the broadcast SSIDs and/or assign preferred passwords to the device, you can type in
the IP-address of the device at the address field in the web browser if your computer is connected
to the Local Area Network Otherwise, you can wirelessly connect to the default SSID “My Private-
XXXXXX” using the serial number of the device as the passphrase and then typing the IP-address
of the device in your web browser
5

Installing additional devices
Because of the Mesh capabilities, additional devices can be added wirelessly or by the wired LAN
If you want to add it wirelessly, place the additional device close to the first device with the wired
internet access
Single Step
Confirm that the first device is powered up and connected to your internet router Power up the
additional device The device status light will start blinking constantly for next 2 minutes
In the wireless network scan you can find the SSIDs by ‘My Hotspot is getting ready’ while the
additional device is preparing itself Once the initial setup is complete , the device will reboot and
now you will find 2 SSIDs with 2 different assigned IP addresses You can now power if off and
relocate the additional device in the wireless blindspot area where you want to extend the wireless
coverage
6

___________________________________________________________________________
Completion of "Quick Installation Guide"
Kindly visit http://www wifiabc com and click on Knowledge Base for a complete
guide and tutorials on the Captive Portal Ready Devices, such as changing SSIDs,
adding or changing passphrase, blocking guest to Local Area Networks and VLANs
configuration
Quick Troubleshooting notes:
Cannot see the SSID “HotspotAABB[email protected]. .8”
Make sure the device is properly connected to your Local Area Network or Internet router which
has access to the internet If connecting additional devices by wireless mesh to the first device, try
not to exceed 10 meters during initial setup After setup, you can relocate it further To restart initial
setup, power up device for at least 1 minute, then press-holding the reset button for 12 seconds
before releasing with a pointed object You can verify the device's response from the LED lights
Cannot connect to “My Private-AABBCC” or “HotspotAABB[email protected]. .8”
The 2 SSIDs are secured with an encryption pass-phrase The pass-phrase is the serial number of
the device and also can be located on the ID-Sticker (key)

My personal Notes:
My MAC Address
88 : DC : 96 : : :
(SSID)Name Password
Account Name
Guest Access
Node Name (SSID#1)
Node Name (SSID#2)
My Memos:
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
8