EOS EMOTEC C 55 User manual

1
Assembly and Operating
Instructions
EMOTEC C 55
IP x4
GB
Druck Nr. 29342434en / -32.06

2
Table of Contents
GeneralInformation ............................................................................................ 15
DeliveryScope ................................................................................................... 16
GeneralSafetyRegulations ................................................................................ 16
InstallingtheControl Device ............................................................................... 16
Wall Mount .............................................................................................. 16
Electric Supply................................................................................................... 18
Operation ........................................................................................................... 19
ButtonFunctions ..................................................................................... 19
CommissioningtheDevice ....................................................................... 20
Activatingthe Devicefor theFirst Time..................................................... 20
Pre-SetParameters ................................................................................. 20
Manual ColouredLightSelection .............................................................. 20
AutomaticColoured LightSelection ......................................................... 21
Effects ofthe Colours ......................................................................................... 22
ConnectionDiagram ........................................................................................... 23
TechnicalData ................................................................................................... 23
Warranty ............................................................................................................ 24
english

3
DearCustomer,
withthiscolouredlightcontroldevice,you
havepurchasedahigh-qualityelectronic
device, which was designed and
producedaccordingtothelateststandard
andquality guidelines.
With this high-quality coloured light
controller, you "operate" your coloured
light device and with the programming
options, you will surely quickly find the
settingsyou feelmost comfortablewith.
Readtheseinstructions carefullysothat
you will find your way through
programmingfast andeasily.
General Notices
The coloured light control device is
intendedfor230V50Hzvoltageandhas
tobesecuredseparatelywitha10Afuse.
Only an authorized electrician may
install and connect the sauna
equipment as well as other electric
devices.
The regulations of the Electrician's
Association (VDE 0100 / Part 703 /
2006-2) must be observed.
As a rule, sauna equipment may only
be connected via a permanent mains
connection. This must enable you to
separate all poles of the device from
the mains with a contact opening
width of at least 3 mm.
Read the following installation and
operatinginstructionscarefullytoensure
the error-free operation of your sauna
system.
General Information
english

4
Delivery Scope (changes reserved)
Thecontrol deviceconsists of:
lPlastic bag with three attachment
screws4x20mm andthree distancer
tubes as well as 3 rubber sleeves.
General Safety Regulations
lOnly an authorized electrician may
install the electronics.
lTheregulations ofyour powersupply
company as well as the pertinent
regulations of the Electrician's
Association(DIN VDE0100)must be
observed.
lCareful mortal danger! Never per-
formrepairsandinstallationsyourself.
Onlyanexpertmayremovethecasing
cover.
lThe device may only be operated in
accordancewithitsintendedpurpose,
meaning as a control device for
colouredlight devices.
lAll poles of the device must be
separated from the mains prior to all
installationand repairwork, meaning
you have to turn off the fuses and/or
main switch.
lObserve the safety and installation
noticesof themanufacturer.
Installing the Control Device
Wandbefestigung
Thecontrol devicemay onlybe installed
outside of the cabin. If there are already
empty tubes for electric installations,
thesedeterminethepositionofthecontrol
device. Proceed as follows for the
installation:
1. Takeoffthecoverofthecontroldevice.
To do so, press the latches inwards
withaflat screwdriverandpull outthe
top part of casing by turning it (ill. 1).
The borings Ø 3 mm for the supplied
wood screws 4 x 20 mm are made in
thedimensionsindicatedin ill.3 +3.1.
2. Screwone ofthewooden screwsinto
thetopcentrehole.Thecontroldevice
issuspendedfrom thisscrew.For this
purpose, let the screw protrude
approx. 3 mm (ill. 3.2).
3. Hangthecontroldeviceintothescrew,
which protrudes 3 mm from the top
attachmenthole.
Insertthesuppliedrubbersleevesinto
theopeningsonthebackofthecasing
andthenguide theconnectioncables
throughtheseopenings
Screw the bottom part of the casing
with the two bottom borings tightly
onto the cabin wall (see ill. 4).
Ill. 1
english

5
Notice: If the sauna cabin is not
equipped with empty tubes, the sauna
leads must be installed on the outside
of the cabin, preferably in a groove of
theprofileboards.Therefore,the control
devicemustbeinstalledwithaslightgab
toenable youto guide thecables tothe
controldevice.This iswhatthe supplied
distancer tubes are for, which keep the
bottompartataslightdistanceasshown
in ill. 3.3.
33
Ill. 3.3Ill. 3.2
Ill. 3.1
Ill. 3
Guide for mains lead
Guide for the lamp
Top attachment hole
Attachment holes
approx. 20 cm
Eye level
approx. 34 cm
19 cm
Eye level
17,4 cm
Ill. 4
english

6
Lead for coloured light
Air inlet
Ill. 5
Mains lead
Electric Connection
Only an approved electrician may
install the electric equipment under
observance of the guidelines of the
local power supply company and the
Electrician'sAssociation.
Asa rule,theremay onlybeone perma-
nent mains connection. This must
enable you to separate all poles of the
device from the mains with a contact
opening width of at least 3 mm.
All electric installations and all
connectionleadsthatareinstalledinside
the cabin must be designed for an
ambient temperature of at least 140°C.
Therespectiverequiredcableprofilesare
listed in the following table.
Themainsleadsareguidedtothecontrol
deviceandconnectedto themainsinput
clamps as shown in ill. 5.
Aconnectionplan isaffixedto theinside
ofthe controldevice forthis purpose.
english

7
Ill. 6
Button Functions
On/Off
operating switch
Single colour
and
automatic
operation
Mode
Program
button
Setting
buttons
Mode
Operation
123456
min 78910
LEDs for colours LED for
operational
readiness
LED for colour
runtime
english

8
Commissioning the Device
After you have once again checked all
connections,commission thedevice by
activating the fuses and/or the main
switch.The devicesignals itsreadiness
for operation with the green LED on the
icon.
Activating the Device for the First
Time
Bypressing thestart/stop button forthe
first time after activating the supply
voltage, the device goes into its basic
mode.Theredlamp islit onthecoloured
light device and the red LED on the
controldevice.
Inautomaticoperation, 5LEDsare litfor
aperiod offiveminutes.
Preset Parameters
lManualcolour selection
lRuntime of the individual colours in
automaticoperation 5minutes
lRuntime of the mixed colours in
automaticoperation 10seconds
Manual Coloured Light Selection
You canselect betweenindividual and
mixedcolours withthe up/down
buttons.
123456
min 78910
123456
min 78910
MODE
MODE
english

9
Automatic Coloured Light Selection
The automatic coloured light selection
isactivated bypressing thelight button.
Withautomatic colouredlight selection,
the colour sequence is red-red/yellow-
yellow-yellow/green-green-green/blue-
blue-blue/red. In the basic setting, the
individual colours remain for 5 minutes
and the mixed colours for 10 seconds
(see"Preset Parameters").
The following settings can be
programmed in the automatic pro-
gram:
You can set the staying time between 1
min. and 10 minutes. Press the MODE
button and the LED line starts blinking.
Youcanchangethetime bypressingthe
up/downbuttons.
BypressingtheMODE buttonagain,the
set value is taken over and the
correspondingnumberofLEDs lightsup
in the LED line (5 minutes = 5 LEDs, 10
minutes = 10 LEDs, etc).
Thestayingtimeofthemixedcolourscan
be set to 10 seconds (basic setting) or
theruntimeofthe individualcolours:
Keeptheupanddownbuttonsdepressed
simultaneouslyfor2secondsuntiltheLED
line blinks briefly. It is reset when you
pressthese buttons onceagain.
If the control is not separated from the
mains, the last set parameters remain
active.
123456
min 78910
MODE
+
MODE
english

10
Effectsof the Colours
The mental effect of the colours takes
placeviatheeyes.Fromthere,thecolour
radiation is transferred to the brain by
meansofcomplexprocessesandunfolds
its effect there in the shape of specific
imaginationsand energies.
The absorption by the nerves leads to
an activation of the body's immune
system. Certain body systems are
addressed and activated depending on
the type of colour.
The physical absorption essentially
takes place via the skin through direct
colourradiation.
Thechemical absorptiontakesplace in
thegastrointestinal tractin the shapeof
"mixed food" in all colours.
english
Blue,thecolourofthe skyand thewater,
isassociatedwith longing,vastnessand
cold. Cold slows down the human
functions, which is the reason why blue
is supposed to have a calming and
relaxing effect and help with nervous
disorders, insomnia, restlessness and
states of anxiety.
Greenis thecolour of nature.Green light
hasasoothing andinspiringeffectat the
same time. It provides relaxation and
regeneration.Greenlight issupposedto
have a positive influence on the
bronchials and the lungs and help with
nervous disorders, headaches and
inflammationof thejoints.
Yellow is supposed to increase the po-
sitiveattitudetowardslifeandthegeneral
well-being. Yellow may stimulate and
strengthen the nerves as well as
dissipategloom andmelancholy. Itmay
also help to balance gastrointestinal
complaints.
Red is associated with fire and blood.
Thecolourof activity,vitalityandwarmth
is supposed to stimulate the circulation
andthiscontribute toageneral increase
ofwell-being andvitality.

11
Connection Diagram
Technical Data
Mainsvoltage: 230 V AC 50 Hz
Fuse: 1 x 10 A
Outputper lamp: max. 400 W
Ambient temperature: 0 to 40°C
Protection class: IPX4
Coloursequence
withautomatic operation: red-red/yellow-yellow-yellow/green-green-
green/blue-blue-blue/red
Colour overlaptime: 10 seconds
Cycle time: adjustable from 1 to 10 minutes
Installation dimensions H x W x D: 240 x 230 x 70 mm
Weight: approx. 1 kg
english
Observe coding of feed lines
to colored light unit
L1
L
N
N
N
Electronic
circuitry
Colored light unit
Line power feed
3 x 1.5 mm²
230 V/50 Hz
Illust. 7
23 5 1

12
Please keep this address together with
the installation instructions in a safe
place.
Inorder forus tobe ableto answeryour
questions in a fast and competent
manner, please always state the data
indicated on the type plate like type
name, item number and production
number.
Serviceaddress:
EOS-WerkeGüntherGmbH
Adolf-Weiß-Str.43
35759Driedorf-Germany
tel [phone]
fax [phone]
[email protected]
www.eos-werke.de
Warranty
The warranty extent orients itself on the currently
valid statutory regulations.
Manufacturer's Warranty
--The period of warrenty starts from the date of
purchase and lasts up to 2years for
commercial use and 3 years for private use.
- We will only perform warranty services upon
presentationof the sales receiptfor the device.
- Any warranty will be null and void in case of
changes to the device without the expressive
consent of the manufacturer.
- The warranty will also be null and void in case
of defects due to repairs or modifications by
unauthorized persons or improper use.
- In case of a warranty claim, please indicate the
serial number as well as the item number
together with the name of the device and an
explicit error description.
- This warranty extends to defect device parts
with the exception of normal wear and tear. In
case if a warranty claim, return the device to
our
service department in its original or suitable
packaging (ATTENTION: danger of transport
damage).
Always return the device with this completed
warranty note.
We will bear assume any possible transport
costs for sending and returning items.
Commissionedon:
Authorized electrician's stamp and
signature:
$
english
Attention!
Dear customer,
according to the valid regulations,
the electrical connection of the
sauna heater and the control box has
to be carried out through the special-
ist of an authorized electric shop.
We would like to mention to the fact
that in case of a warrenty claim, you
arekindlyrequested to present a copy
of the invoice of the executive
electric shop.