EOS ProControl 2 plus Series User manual

PROCONTROL
SERIES 2plus USER MANUAL
Version 2.2X
EOS Research, Ltd.

ProControl User’s Manual v2.2X
\8100\0074_1017
i
LIMITED WARRANTY
EOS Research, Ltd. (EOS) warrants its products to be free from defects in materials and workmanship for a period
of one year from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its
sole option, any such defective products. This warranty includes parts and labor. This warranty does not apply to
equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in
any way.
EXCEPT AS PROVIDED HEREIN, EOS RESEARCH LTD. MAKES NO WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING WARRANTIES OF MECHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. Some states do not permit limitation or exclusion of implied warranties, therefore the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
IMPORTANT SAFETY PRECAUTIONS
Any complex hardware or software may be difficult to document, explain or understand. It is important to consider
the consequences or unexpected or abnormal behavior which may be caused by a defect or human failure to
comprehend. In order to protect people and property from damage, a thorough safety analysis should always be
performed. When the consequences of a failure are serious, it is essential to protect life and property against such a
failure with redundant backup systems or safety devices. It is agreed between the purchaser and EOS Research,
Ltd. that protection against and the consequences of any such failure are entirely the purchaser!s responsibility.
This device is not approved for use in life support or medical systems.
As installed, this product may be part of a system which is required to meet various electrical, fire, safety or other
codes and regulations. Compliance with these codes is the purchaser!s responsibility.
Specifications subject to change without notice.
© 1996-2017 EOS Research, Ltd.
EOS Research, Ltd.
159 Walnut Street
Rochester, NH 03867
603.332.2099
Fax: [phone]
[e-mail]

ProControl User’s Manual v2.2X
\8100\0074_1017
ii
TABLE OF CONTENTS
1.0 SYSTEM OVERVIEW 1
1.1 General 1
1.2 Key Concepts 2
1.3 Control Basics 3
2.0 ON-SITE OPERATION 7
2.1 LCD Display 7
2.2 Keypad 9
2.3 Password 10
2.4 Operations Screen 10
2.5 I/O Keys 11
2.6 Digital Input Menu 11
2.7 Digital Output Menu 11
2.8 Analog Input Menu 12
2.9 Analog Output Menu 13
2.10 Menu Key 14
2.11 LED Indicators 19
3.0 REPORTING FEATURES 20
3.1 Fax Report (Dial-up Modem Units) 20
3.2 Text Message or Page Alerts 23
3.3 Email Report (Ethernet and Cellular Data Units) 23
APPENDIX A - Typical ProControl Wiring
Please see the ProView User!s Guide for operation of the remote access software which is
supplied with the ProControl Series 2plus.

ProControl User’s Manual v2.2X
1 \8100\0074_1017
1.0 SYSTEM OVERVIEW
1.1 General The ProControl Series 2plus is a small but powerful supervisory control and data
acquisition (SCADA) system. By combining process control and remote capabilities
in one unit, the Series 2plus can act as a central supervisory and data management
tool for any stand-alone operation. The ProControl Series 2plus can perform
multiple tasks:
•Stand-Alone Control: The ProControl Series 2plus provides powerful and
straightforward, event-driven process control; everything from simple on/off
control to complex startup sequences and PID control loops. It can interface
with up to 78 electrical devices (float switches, pressure transducers, pH
transmitters, flow meters, pumps, blowers, etc.), and will simultaneously execute
several control routines for your operation. It is an extremely versatile process
controller.
•Remote Control and Monitoring: The ProControl Series 2plus gives you a
window into your operation from any remote location, with our easy-to-use
PROVIEWTM software and reliable, proven communications via broadband
internet, cellular data connection or land-line modem. You!ll have the same
level of control as if you were at the site. No other SCADA controller gives you
the ProControl!s level of real-time remote control capability.
•Reporting: The ProControl Series 2plus will keep you informed, with
scheduled email or fax status reports, and instant text/pager messages for alarm
conditions. No longer do you have to assume what!s happening at your remote
operation.....the ProControl will tell you exactly.
•Datalogging: As your information manager, the ProControl Series 2plus will
record all operating conditions in its internal memory, while keeping track of
flow totals, duty cycles, etc. Have your data emailed to you, or access your
system remotely for download or review at any time. The ProControl is an
invaluable tool for reporting, troubleshooting and trend graphing.
One or more of these features can be used in your installation; they are standard in
every ProControl unit.

ProControl User’s Manual v2.2X
2 \8100\0074_1017
1.2 Key
Concepts
The following are the building blocks of any Series 2plus monitoring and control
system.
Inputs and
Outputs (I/O’s)
No system can be effective in the real world without communication and one of the
principal ways the ProControl communicates is by responding to information
collected by sensors and by issuing "commands#to other electronic or electrical
devices. Sensor information constitutes an Input while a "command#to another
device constitutes an Output. The Series 2plus works with all of the more important
types of I/O devices in general use. Appendix A demonstrates how a variety of I/O
devices are connected to the ProControl.
Digital Inputs
These inputs are designed to detect the closure of switch contacts such as those
found on float switches or overpressure sensors. They can respond to any normally
open or normally closed dry contact. The Series 2plus provides its own wetting
(supply) voltage of 5 volts DC for each digital input circuit. The Series 2plus can
respond to changes in state as fast as 4 Hz or 3 Hz (cycles per second) depending on
the model purchased. Digital inputs are "debounced#for 125 or 150 milliseconds,
respectively. This means that a switch or other input that changes state (becomes
open or closed) must stay in that state for 125 or 150 milliseconds before the Series
2plus will respond to the change.
Up to eight high-speed digital inputs can also be used for traditional digital (pulse-
output) flow meters. These inputs can detect signal changes at up to a 200/500 Hz
rate. All high-
speed digital inputs are "debounced#for 1250/500 microseconds.
The faster rate applies only to Type A ProControl units.
Analog Inputs
These inputs are compatible with sensors which send out a 4 - 20 milliamp (mA)
signal. Most analog sensors are available with this type of signal, examples being
pressure transducers, pH transmitters, and many flow meters. These inputs allow
the operator to read the actual "value#of a parameter, such as pressure, instead of
an on/off signal.
Digital Outputs
Digital outputs turn things like pumps, solenoid valves, and alarm lights on and off.
The Series 2plus digital outputs are relay outputs designed to switch small loads
directly, such as motor starters, lamps, and solenoid valves.

ProControl User’s Manual v2.2X
3 \8100\0074_1017
Analog Outputs
Analog outputs are typically used in process control schemes where a controlled
piece of equipment can accept a signal which is variable over a range. This output is
expressed as a percentage (0 - 100%) and is used to control pump speeds, chemical
dosing rates, etc., instead of conventional on/off operation. The equipment that the
ProControl sends the analog output to must accept a 4 - 20 mA signal. Often, an
analog output is used in conjunction with an analog input such as a pH transmitter
to form a control scheme known as feedback control. In essence, the input and
output will work together to maintain a user set input level. This concept is
described further in the next section under Analog Output Processes.
Tagnames
Each input and output is given a descriptive Tagname by the user that uniquely
identifies it to the system operator. For instance, a digital input could be called
"TANKHI#, an analog input could be called "AIRFLO#and a digital output could
be called "PUMP_1#. This tagname is used by the local LCD display, the email/fax
reports and by the ProView software. The analog inputs are also given a Units
Tagname w
hich identifies the unit of measure associated with the input sensor.
Each tagname can be up to six characters long and each units tagname can be up to
three characters long ("PSI#, for instance). The tagnames can include the uppercase
letters A-Z, the numbers 0-9, a blank space, and the underscore (_) character.
1.3 Control
Basics
The status of all inputs or outputs can easily be monitored both locally and remotely.
What gives the Series 2plus its real power, however, is the ability to automatically
initiate actions based on the status of the inputs and your pre-programmed
instructions (this is often called Process Control). These actions can include
switching certain outputs, sending an email report, sending an text message, shutting
down the entire system or sounding the local alarm. Process control functions are
programmed into your ProControl by EOS Research or one of our technology
partners according to your specifications.

ProControl User’s Manual v2.2X
4 \8100\0074_1017
Active State
Central to the use of control on the Series 2plus is the concept of Active State. Each
input on the ProControl receives certain signals from a sensor which constitute
"normal#operation and other signals which constitute an exception to normal
operation.
A digital input can monitor only two states, ON or OFF (alternatively, CLOSED or
OPEN). The Active State would be the state in which the controller would respond
to the digital input, and perform certain actions or generate an alarm. For example,
if a high level float switch in a tank is tripped (turned ON) by rising fluid level, we
can say that its Active State
correlates to a situation in which the fluid level is high.
The active state of the float switch could cause the Series 2plus to trigger an alarm,
turn off a pump, or initiate some other action. The Series 2plus can be set up so that
either ON or OFF is the active state.
An analog input sensor can take on many states (or values) between the minimum
and maximum of its measurement range. The ProControl operator, however, can
set two threshold values which divide the total input span into two functional
regions. These threshold values are more commonly called the Low Alarm Limit
and the High Alarm Limit, although on the Series 2plus these thresholds are
somewhat more flexible in use than those names imply. An analog input which has
transcended either its Low Alarm Limit or High Alarm Limit is said to be in its
active state.
EAS WAS
0 psi
10 psi
Low
High
6
4
Figure 1. Active State
For instance, consider an analog input sensor which measures
pressure from 0 to 10 PSI. The system operator could set the low
limit to 4 PSI and the high limit to 6 PSI. In this case the Active
State would usually be considered as the input state greater than 6
PSI or less than 4 PSI. This interpretation is called Endpoint Active
State (EAS) on the Series 2plus because the endpoints of the range
are the areas which need to trigger action or generate alarms. The
opposite interpretation (though rarely used) is also possible and is
called Window Active State (WAS). Any input values between 4 PSI
and 6 PSI would trigger action or generate alarms.
If the ProControl has Alarms Set, when any input enters its active state, a local
beeper will sound on the ProControl. The word Alarm here applies only to the
sounding of a local beeper and is not associated with any process control. The
active state condition is indicated on the LCD display and can be acknowledged by
the operator. The beeper is silenced when it has been acknowledged or after 30
seconds have elapsed. The beeper only operates when the system is operating in
Manual mode.

ProControl User’s Manual v2.2X
5 \8100\0074_1017
Startup
Sequence
The Startup Sequence is a series of control algorithms or steps which run in
succession and which are designed to place the system in its normal operating mode.
It can be as simple as turning all the outputs on simultaneously, or as complex as a
multi-stage delay with many conditions. Up to 8 or 16 individual startup steps can
be declared depending on the model of the controller. The ProControl can be
configured to automatically run this sequence when the unit is powered up.
Process Tasks
A Process Task is an ongoing control algorithm which runs continuously. Think of
each process task as an IF-THEN statement, in which an action is initiated if a
certain condition or combination of conditions exists. Some examples are:
•IF Tank Level Sensor 2 is on, THEN turn Pump 2 off
•IF Air Flow Rate < 10 cfm AND Reactor Temperature > 250o, THEN open Bleed
Valve 2
Up to 32 or 64 separate process tasks can be run simultaneously depending on the
model of the controller. Process tasks can trigger email reports, text message alerts,
and system shutdowns.
Shutdown
Sequence
The Shutdown Sequence is a series of control steps which run in succession and
which are designed to shut your system down in a manner which is best for the
equipment or treatment processes involved. The shutdown sequence can be
activated manually or automatically due to an alarm condition. Here is an example
shutdown sequence:
•Turn off Well Pumps 1 and 2
•Wait 5 minutes, then turn off Air Stripper Blower
•Open Bleed Valve 2
•When Oxidizer Temperature < 150o, turn off SVE Blower
Automatic
Operation
The use of the startup sequence, process tasks, and the shutdown sequence
constitutes Automatic Operation of your system with the ProControl Series 2plus
(otherwise known as Auto Mode). The Series 2plus will be placed into auto mode
(automatically) when your system has been started up using the programmed startup
sequence. If one condition of the programmed startup sequence is not met during
the startup process, your system will be completely shut down by the ProControl as
a safety measure. Once the startup sequence has been successfully completed, the
ProControl begins running the process tasks continuously. PROCESS TASKS WILL
RUN ONLY WHEN IN AUTO MODE. Please note that the audible beeper will not
sound even if the ProControl has Alarms Set when it is in Auto Mode, since the
process tasks will control these situations as the user has specified.

ProControl User’s Manual v2.2X
6 \8100\0074_1017
Manual
Operation
You can override the Series 2plus programmed control functions by operating in
Manual Mode. In manual mode, your process will respond only to operator input
from the keypad of the ProControl, or to commands issued from the ProView
software. PLEASE NOTE THAT PROCESS TASKS AND THEIR ERROR-CHECKING
MECHANISMS DO NOT RUN DURING MANUAL MODE!Manual mode is useful when
you wish to troubleshoot your system, but none of the system safeguards built into
auto mode are available. You can place your operation into auto mode any time by
issuing the command from the keypad.
Analog Output
Processes
In some cases, you may want to use an analog output to control equipment that
maintains an analog input at a certain constant level. For example, you may wish to
automatically maintain a pH of 8.5 in a reaction tank by varying the dosing rate of a
chemical feed pump. The pH you wish to maintain (8.5) is called the SetPoint of the
analog output process. An analog input to the ProControl (in this case, a pH
transmitter) is said to provide feedback to the unit, and combined with an analog
output, constitute feedback control.
PID Loops
A reliable type of feedback control can be obtained through a PID Loop. PID
stands for Proportional-Integral-Derivative, and is a commonly-used process
control technique. We!ll skip the details of the mathematics involved, but suffice it
to say that a PID loop is the favored control technique for most analog output
processes. With only a Proportional term applied in the equation, the analog output
is controlled based on an error signal generated from the difference between the
SetPoint and the actual analog input. The PID loop can also improve its
performance as it continues to run if an Integral term is used, and can respond to
quick changes in the controlling analog input if a Derivative term is used. EOS
Research or your control system integrator will configure your PID loops for you
and can provide further information if necessary.
Proportional
Outputs
In some cases, it may be desirable to base an analog output signal on an analog input
value. In this situation, no specific SetPoint is used because there is a direct
relationship between the output and input values. For example, if you wanted to
base the output of a metering pump on some flow rate, you might use a proportional
output to relate the amount of chemical metered to the flow rate.

ProControl User’s Manual v2.2X
7 \8100\0074_1017
2.0 ON-SITE OPERATION
2.1 LCD
Display
If your unit did not come with an LCD display, the following sections do not
apply.
The 2 line x 20 character LCD display is used to display and control system
operations. The display is divided into separate areas or fields, as outlined below.
AIRFLO 343.65 CFM
AUTO 12
System Tagname Tagname Value
Dimensional Units
or I/O Status
or Output Designation
System Status
Menu Selection
REPORT OFF
Communications
Status
SP
Figure 2. Display Fields
System Tagname
This six-character field is used to identify the I/O point displayed. Descriptive
names such as WELL1 or BLOWER are used.
Tagname Value
For analog inputs, this field displays the value of the input, the high alarm limit, or
the low alarm limit. For digital outputs, OUTPUT is displayed. For digital inputs,
this field is unused. For analog outputs, this field displays the output percentage,
the output level, or the associated input setpoint.
Dimensional
Units or I/O
Status
For analog inputs, this three-character field displays the dimensional units
associated with the input sensor, such as GPM or PSI. For digital inputs and
outputs, this field displays either ON or OFF. For analog outputs, this field
abbreviates percent with PCT. In the case of digital outputs, if the particular
output displayed has been designated a lamp output (see ProView manual), and a
lamp test is currently running, an asterisk (*) will appear before ON or OFF to
indicate the lamp is illuminated despite the indicated output status (the output will
return to this indicated status once the lamp test has been completed).
Menu Selection
This field displays the current menu selection.

ProControl User’s Manual v2.2X
8 \8100\0074_1017
Communications
Status
This field displays one of five different descriptors which indicate any of several
special functions of the ProControl. If no communications action is being taken,
">#will appear. Communications messages include: SP (Sending Page or text
message) - indicates that the unit is attempting to send either an alphanumeric or
numeric message; EF (Encoding Fax) - indicates that the unit is presently
encoding a facsimile report as a result of a request by either the operator or the
unit itself; SF (Sending Fax) - indicates that the unit is attempting to send a fax
report; SE (Sending Email) - indicates the unit is sending an email; and DC (Data
Communications) - indicates that the unit is presently interfaced with ProView.
System Status
This area displays the current system status: AUTO, MANUAL, START, or
SHUTD and an associated process task number indicating the last successfully
completed Auto process, current Startup process, or current Shutdown process.

ProControl User’s Manual v2.2X
9 \8100\0074_1017
2.2 Keypad
The Series 2plus keypad contains 12 buttons which are used along with the LCD
Display to control the operations of the system. The Type C ProControl has a 4-key
keypad with more limited functionality.
Ÿ
Up ⁄
Down
Ÿ
I/O ⁄
I/O
Field
Menu
Enter
!
Ack Hi Lo
Set
Mode
Man Mode
Auto
Figure 3. Series 2plus Keypad
Menu
This key is used to scroll through a series of options which are displayed on the
LCD screen, and which allow the user to configure various aspects of system
behavior.
Ÿ
I/O ⁄
I/O
These keys are used to display information about particular I/O points on the LCD
Screen. The keys allow the user to scroll through all of the system I/O points either
forward or backward.
Ack
The Acknowledge key is used to silence the audible beeper or to acknowledge a
memo sent from a remote ProView user.
Hi Lo
Set
The Set Hi Lo key allows the user to change the high and low alarm limits for
analog inputs or to toggle the display in the I/O Summary.
!
The Emergency Shutdown key is used to turn off all outputs and return the system
to manual mode. The programmed shutdown sequence is not executed using this
key.
Field
The Field key is used to select a character position to be edited. It is used in
conjunction with any direct alphanumeric entry.
Ÿ
Up ⁄
Down
These keys are used to toggle system variables from one state to the next or to
scroll through possible character entries when used in conjunction with the Field
key.
Mode
Man
This key is used to place the system in manual mode.
Mode
Auto
This key is used to place the system in auto mode.
Enter
The Enter key is used to initiate certain actions selected by other keys or to confirm
alphanumeric editing done using other keys.

ProControl User’s Manual v2.2X
10 \8100\0074_1017
2.3 Password
When the system is first turned on the password screen is displayed and the user is
prompted to enter the password to gain access to the system. "EOS#is the default
password. The password on the Series 2plus was designed as a low-level security
feature. It is not sufficient in and of itself to withstand a determined effort at system
entry. The ProControl unit can be configured to bypass the password screen when
the unit is powered up.
Ÿ
Up ⁄
Down
CUSTOMER ID TAGNAME
ENTER PASSWORD: BAA
_
Use the Up and Down keys to change
the character displayed above the
cursor.
Field
CUSTOMER ID TAGNAME
ENTER PASSWORD: BAA
_
The Field key is used to move the
cursor to the next character to be
edited.
Enter CUSTOMER ID TAGNAME
ENTER PASSWORD: EOS
_
The enter key submits the password
for approval.
If the password was entered correctly, the following screen will be displayed for
about a second before the operations screen is displayed:
Password Accepted
VER 2.XXX : 1
ROM Version # User Setup Version #
Otherwise, the following message will be displayed for a second and the user will be
returned to the password menu:
Incorrect Password
2.4
Operations
Screen
After the password has been entered correctly, the operations screen is displayed.
The operations screen allows the user to set system parameters and to review the
status of all system inputs and outputs.
WELL1 OFF
ALARMS SET
>MANUAL

ProControl User’s Manual v2.2X
11 \8100\0074_1017
2.5 I/O Keys
Ÿ
Up
⁄
Down
Ÿ
I/O
⁄
I/O
Field
Menu
Enter
!
Ack Hi Lo
Set
Mode
Man Mode
Auto
Pressing the I/O Up or I/O Down keys
will scroll through the operational I/O
points in the system. Data relevant to
a particular I/O point will be displayed
to right of the point!s Tagname.
Ÿ
I/O
WELL2 ON
ALARMS SET
>MANUAL
Forward scroll through I/O points
Ÿ
I/O
WELL3 OFF
ALARMS SET
>MANUAL
Forward scroll through I/O points
⁄
I/O
WELL2 ON
ALARMS SET
>MANUAL
Backward scroll through I/O points
2.6 Digital
Input Menu
WELL2 ON
ALARMS SET
>MANUAL
Input Tagname
Input Status
A digital input displayed in the
operations screen will be displayed as
shown. When the input is in its Active
State "ON#will be displayed in the
Input Status area. Otherwise, "OFF#
will be displayed.
2.7 Digital
Output
Menu PUMP1 OUTPUT *OFF
ALARMS SET
>MANUAL
Output Tagname
Output Status
_
Lamp Status
A digital output displayed in the
operations screen will appear as
shown. When the output has been
turned on, "ON#will be displayed in
the Output Status area. Otherwise,
"OFF#
will be displayed. The cursor
is displayed under the first character in
the status field to indicate that it can be
changed. The Lamp Status character
(*) will be shown for a lamp output if a
lamp test is running regardless of the
output!s true state.
Ÿ
Up ⁄
Down
PUMP1 OUTPUT ON
ALARMS SET
>MANUAL
_
Pressing the Up or Down key will
toggle the digital output state and turn
the corresponding relay OFF or ON.
Field
PUMP1 OUTPUT ON
ALARMS SET
>MANUAL
_
Pressing the Field key will move the
cursor to the Menu selection field.

ProControl User’s Manual v2.2X
12 \8100\0074_1017
2.8 Analog
Input Menu
H2OFLO 54.6 GPM
ALARMS SET
>MANUAL
Analog Tagname
Units
Analog Value
An analog input displayed in the
operations screen will be displayed as
shown to the left. The value of the
analog input will be shown along with
the dimensional units. In the case of a
pulse accumulator (totalizer only), you
will see only TOT where units is
normally displayed.
Hi Lo
Set
H2OFLO 20.0 GPM
LOW ALARM >MANUAL
_
Use the Set Hi Lo key to set the low
alarm limit.
Hi Lo
Set
H2OFLO 80.0 GPM
HIGH ALARM >MANUAL
_
Press the Set Hi Lo key again to set
the high alarm limit.
Hi Lo
Set
H2OFLO 120817 GAL
TOTAL FLOW >MANUAL
Press the Set Hi Lo key again to see
the total flow on a flow type input, and
once more to return.
Ÿ
Up ⁄
Down
H2OFLO 30.0 GPM
LOW ALARM >MANUAL
_
The Up and Down keys are used to
change the value of the current
character, as denoted by the cursor.
Field H2OFLO 30.0 GPM
LOW ALARM >MANUAL
_
The Field key is used to move to the
next character to be edited.
Enter H2OFLO 30.0 GPM
LOW ALARM >MANUAL
_
To save the low alarm limit changes,
press the enter key.

ProControl User’s Manual v2.2X
13 \8100\0074_1017
2.9 Analog
Output
Menu
VRPUMP 25.0 PCT
ALARMS SET
>MANUAL
Analog Tagname
Percentage
An analog output displayed in the
operations screen will be displayed as
shown to the left. The percentage of
full scale output will be displayed as
well.
Hi Lo
Set
Hi Lo
Set
VRPUMP 25.0 PCT
OUTPUT LVL >MANUAL
_
WTRLVL 33.0 FT
SETPOINT >MANUAL
_
The Set Hi Lo key can be used to set
the output percentage.
Press the Set Hi Lo key again to
declare the SetPoint of an associated
analog input. The SetPoint is used
only if a PID control loop is in use as
an analog output process.
Pressing Set Hi Lo again returns to the
original menu.
Ÿ
Up ⁄
Down
VRPUMP 35.0 PCT
OUTPUT LVL >MANUAL
_
The Up and Down keys are used to
change the value of the current
character, as denoted by the cursor.
Field
VRPUMP 35.0 PCT
OUTPUT LVL >MANUAL
_
The Field key is used to move to the
next character to be edited.
Enter
VRPUMP 35.0 PCT
OUTPUT LVL >MANUAL
_
To save the output level changes, press
the enter key.

ProControl User’s Manual v2.2X
14 \8100\0074_1017
2.10 Menu
Key
Ÿ
Up
⁄
Down
Ÿ
I/O
⁄
I/O
Field
Menu
Enter
!
Ack Hi Lo
Set
Mode
Man Mode
Auto
When pressed, the Menu key will
scroll through a series of items which
allow the user to configure various
aspects of system behavior. A
description of these items appear in a
10 character field at the bottom left of
the display. Either the Up and Down
keys or the Enter key is used to
change the item.
ALARMS
Use the Up and Down keys to enable or disable Alarms (audible beeper).
Menu
TAGNAM DIM
ALARMS OFF >MANUAL
TAGNAM DIM
ALARMS SET
>MANUAL
Ÿ
Up ⁄
Down
REPORT
Use the Up and Down keys to enable or disable the unit!s reporting capabilities
(email, fax or text message/page).
Menu
TAGNAM DIM
REPORT OFF >MANUAL
TAGNAM DIM
REPORT ON >MANUAL
Ÿ
Up ⁄
Down
FAX NOW
Use the Enter key to send a FAX report immediately (dial-up modem
communication units only).
Menu
Enter
EMAIL NOW
Use the Enter key to send an email report immediately (Ethernet and cell data
communication units only).
Menu
Enter
TAGNAM DIM
FAX NOW >MANUAL
TAGNAM DIM
EMAIL NOW
>MANUAL

ProControl User’s Manual v2.2X
15 \8100\0074_1017
STARTUP
Use the Enter key to run the Startup Sequence.
Menu
TAGNAM DIM
STARTUP >MANUAL
Enter
SHUTDOWN
Use the Enter key to run the Shutdown Sequence.
Menu
TAGNAM DIM
SHUTDOWN >MANUAL
Enter
LAST
SHUTDOWN
This display item shows what input or output caused the last shutdown.
Menu
LOG OFF
Use the Enter key to Log Off the system and return to the password menu.
Menu
TAGNAM DIM
LOGOFF >MANUAL
Enter
TAGNAM DIM
SDN TAGNAM >MANUAL

ProControl User’s Manual v2.2X
16 \8100\0074_1017
LAST MEMO
Use the Enter key to see the last memo sent from the remote ProView user.
Up and Down are used to scroll through the message, and Ack is used to return to
the ProControl menus. If you hit any other key you will see an informative
message telling you which keys are valid. The message will be displayed for 3
seconds if no keys are pressed, but can be acknowledged before the 3-second
period by pressing either the Ack or Enter keys.
Menu
TAGNAM DIM
LAST MEMO >MANUAL
HEY BULLWINKLE,
REMEMBER TO SHUT THE
LIGHTS OFF!
PUSH <ACK> TO RETURN
UP & DOWN TO SCROLL
OR <ACK>NOWLEDGE
LIGHTS OFF!
PUSH <ACK> TO RETURN
TAGNAM DIM
LAST MEMO >MANUAL
Enter
⁄
Down
Field
Ack
Ack

ProControl User’s Manual v2.2X
17 \8100\0074_1017
IO SUMMARY
Use the Enter key to enter the I/O summary. The analog input values 0-10
represent a percentage of full scale (i.e. 2 @4 mA, 5 @12 mA). Set HiLo is used
to toggle between input/output summaries. An underscore represents an open
input or an unswitched output. A block indicates a closed input or a switched
output. An xor Xis displayed when an output is not enabled and is unswitched or
switched, respectively. An asterisk (*) will be displayed if an output is declared as
a lamp and a lamp test is currently being performed. The Field key can be used to
move the blinking cursor through the outputs. The Up/Down keys can be used to
toggle the state of the
output whose position is covered by the blinking cursor.
The Enter key will return the ProControl back to its standard menus. If you press
any other keys you will see an informative message telling you which keys are
valid. The message will be displayed for 3 seconds if no keys are pressed, but can
be interrupted before the 3-second period by pressing the Enter key.
Menu
TAGNAM DIM
IO SUMMARY >MANUAL
DIN
01234567891001234 AIN
xxx DO
xxxxxxxxxxxxxxxx EXT
xxx DO
xxxxxxxxxxxxxxxx EXT
xxx DO
xxxxxxxxxxxxxxxx EXT
HILO, FIELD, UP/DOWN
CHANGE IO,ENTER EXIT
xxx DO
xxxxxxxxxxxxxxxx EXT
TAGNAM DIM
IO SUMMARY >MANUAL
Enter
Hi Lo
Set
Field
Ÿ
Up ⁄
Down
Mode
Auto
Enter
Enter